Similar Questions

• I need help for configuring security for my wireless again.

  Need a help for my Wi - Fi Protected Access set up again... somehow I deleted it while trying to access the networks wireless outside my house.

  original title: Wi - Fi Protected Access

  Hi dmcangus,

  See the Microsoft articles below for more information on WPA wireless security.

  Configure Security Wireless WPA for home networks

  http://Windows.Microsoft.com/en-us/Windows-XP/help/networking/configure-WPA-wireless-security

  Overview of upgrading security Wi - Fi Protected Access (WPA) in Windows XP

  http://support.Microsoft.com/kb/815485

• Can not get help Bridge CS5-> Access Denied (Win 7 64 bit)

  When I select help > Bridge CS5 help returns the following:

  Access denied

  We're sorry, that you are authorized to access the service you requested.

  If you feel you should have access, please communicate with the competent authorities and give them your IP address: 209.nn.nn.nn

  Thank you for your patience.

  Who are the authorities s ?

  Try these steps:

  http://kb2.Adobe.com/CPS/842/cpsid_84215.html

• Need help bridge database for MS SQL Server, error ORA-28546 configuration problems

  Dear all,

  I'm trying to configure Oracle to MS SQL Server(I don't have admin access to the MS SQL Server) database gateway.  When I try to test the dblink connection, I get the following error.

  I published select * from dual@xyz;

  ORA-28546: initialization of the connection failed, probable Net8 admin error

  ORA-28511: interruption of the RPC connection to heterogeneous remote agent using SID = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=localhost) (PORT = 1521)) (CONNECT_DATA = (SID = dg4msql)))

  ORA-02063: preceding 2 lines of xyz

  28546 0000 - ' failed to initialize connection, unlikely Net8 admin error.

  My setup is as follows.

  1 oracle 11 GR 2 under Oracle Linux 6, the same gateway version is installed on the same server but different base directory.

  2 oracle DB base directory is u01/app/oracle/product/11.2.0/dbhome_1, gateway home directory is/u01/gateway.

  3. I use the same file listener.ora for db and the entry door.

  4. the content of my listener.ora, tnsnames.ora and the initdg4msql.ora is below.

  /U01/app/Oracle/product/11.2.0/dbhome_1/network/admin/listener.ora

  LISTENER =

  (DESCRIPTION_LIST =

  (DESCRIPTION =

  #(ADDRESS = (PROTOCOL = IPC) (KEY = EXTPROC1522))

  (ADDRESS = (PROTOCOL = TCP (PORT = 1522))(HOST = db.abc.com.tw))

  )

  )

  MSSQL =

  (DESCRIPTION_LIST =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP)(HOST = localhost) (PORT = 1521))

  )

  )

  SID_LIST_LISTENER =

  (SID_LIST =

  (SID_DESC =

  (GLOBAL_DBNAME = db.abc.com.tw)

  (ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)

  (SID_NAME = orcl)

  )

  )

  SID_LIST_mssql =

  (SID_LIST =

  (SID_DESC =

  (SID_NAME = dg4msql)

  (ENVS = LD_LIBRARY_PATH = / u01/gateway/dg4msql/pilot/lib: / u01/gateway/lib)

  (Program name = / u01/gateway/bin/dg4msql)

  )

  )

  /U01/app/Oracle/product/11.2.0/dbhome_1/network/admin/tnsnames.ora

  LISTENER_ORCL =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1522))(HOST = db.abc.com.tw))

  ORCL =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1522))(HOST = db.abc.com.tw))

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = orcl.abc.com.tw)

  )

  )

  dg4msql =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP) (HOST = localhost)(PORT = 1521))

  (CONNECT_DATA = (SID = dg4msql))

  (HS = OK)

  )

  /U01/gateway/dg4msql/Admin/initdg4msql.ora

  HS_FDS_CONNECT_INFO=[192.168.0.1]:1433//XIETEST

  # replacement connect format is the name of host/serverinstance/databasename

  HS_FDS_TRACE_LEVEL = 255

  HS_FDS_RECOVERY_ACCOUNT = RECOVERY

  HS_FDS_RECOVERY_PWD = RECOVERY

  the dblink is created with the following statement.

  CREATE DATABASE LINK "xyz.abc.COM.TW".

  CONNECT TO ITS IDENTIFIED BY

  With the HELP of "dg4msql";

  Couple of other things I did to check the above works.

  [oracle@db admin] $ ping 192.168.0.1

  PING 192.168.0.1 (192.168.0.1) 56 (84) bytes of data.

  64 bytes from 192.168.0.1: icmp_seq = 1 ttl = 61 time = 7.61 ms

  64 bytes from 192.168.0.1: icmp_seq = 2 ttl = 61 time = 7,41 ms

  ^ C

  -ping 192.168.0.1 - statistics

  2 packets transmitted, 2 received, 0% packet loss, time 1818ms

  RTT min/avg/max/leg = 7.417/7.516/7.615/0.099 ms

  [oracle@db admin] $ tnsping dg4msql

  AMT Ping utility for Linux: Version 11.2.0.1.0 - Production on 2013-SEPT-11 10:53:11

  Copyright (c) 1997, 2009, Oracle.  All rights reserved.

  Use settings files:

  /U01/app/Oracle/product/11.2.0/dbhome_1/network/admin/SQLNET.ora

  TNSNAMES adapter used to resolve the alias

  Try to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP) (HOST = localhost)(PORT = 1521)) (CONNECT_DATA = (SID = dg4msql)) (HS = OK))

  OK (0 msec)

  [oracle@db admin] $ lsnrctl status mssql

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 2013-SEPT-11 10:54:23

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=localhost) (PORT = 1521)))

  STATUS of the LISTENER

  ------------------------

  Alias mssql

  Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production

  11-SEP-2013 start date 10:09:46

  Uptime 0 days 0 h 44 min 37 sec

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora file

  The listener log file /U01/app/Oracle/diag/tnslsnr/DB/MSSQL/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=127.0.0.1) (PORT = 1521)))

  Summary of services...

  Service 'dg4msql' has 1 instance (s).

  Instance of 'dg4msql', status UNKNOWN, has 1 operation for this service...

  The command completed successfully

  Obviously, I'd like to get this configuration to work, but I have also a couple other questions about this configuration.

  1. for the installation of the bridge, he wants to run the root.sh script.  the script root.sh as to what follows.

  Enter the full path of the local bin directory: [/ usr/local/bin]:

  The 'dbhome' file already exists in the usr.  Overwrite it? (y/n)

  [n]: n

  The 'oraenv' file already exists in the usr.  Overwrite it? (y/n)

  [n]: n

  The 'coraenv' file already exists in the usr.  Overwrite it? (y/n)

  [n]: n

  the above answer is correct?

  Thanks for reading.

  The strace shows:

  2796 open ("/ u01/app/oracle/diag/tnslsnr/db/mssql/trace/mssql.log", O_WRONLY |) O_CREAT | O_APPEND, 0660) = 12

  9564 access ("/ u01/app/oracle/product/11.2.0/dbhome_1/dg4msql/admin/initdg4msql.ora", F_OK)

  2796 write (12, "2013-SEPT-11 15:02:44 * (CONNECT_"..., 175 ")")

  9564 <... access="" resumed="">) =-1 ENOENT (no such file or directory)

  2796 <... write="" resumed="">) = 175

  2796 close (12

  9564 brk (0x14a3000) = 0x14a3000

  2796 <... close="" resumed="">) = 0

  2796 poll ([{fd = 8, events = POLLIN |}]) POLLRDNORM}, {fd = 11, events = POLLIN |} [POLLRDNORM}, {fd-=-1}, {fd = - 1}]-1, 4

  9564 access ("/ u01/app/oracle/product/11.2.0/dbhome_1/dg4msql/log/dg4msql_agt_9564.trc", F_OK) =-1 ENOENT (no such file or directory)

  9564 access ("/ u01/app/oracle/product/11.2.0/dbhome_1/dg4msql/log/dg4msql_agt_9564.trc", F_OK) =-1 ENOENT (no such file or directory)

  9564 statfs ("/ u01/app/oracle/product/11.2.0/dbhome_1/dg4msql/log/", 0x7fff91f005b8) =-1 ENOENT (no such file or directory)

  9564 open ("/ u01/app/oracle/product/11.2.0/dbhome_1/dg4msql/log/dg4msql_agt_9564.trc", O_WRONLY |) O_CREAT | O_TRUNC, 0666) =-1 ENOENT (no such file or directory)

  => so that it always uses the database as Oracle_home House

  With this info, I rechecked the listener and saw that you are missing the ORACLE_HOME setting in the dg4msql section of SID. Please correct your entry to mssql_sid to:

  SID_LIST_LISTENER =

  (SID_LIST =

  (SID_DESC =

  (GLOBAL_DBNAME = db.abc.com.tw)

  (ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)

  (SID_NAME = orcl)

  )

  )

  SID_LIST_mssql =

  (SID_LIST =

  (SID_DESC =

  (ORACLE_HOME = / u01/bridge)

  (SID_NAME = dg4msql)

  (ENVS = LD_LIBRARY_PATH = / u01/gateway/dg4msql/pilot/lib: / u01/gateway/lib)

  (Program name = / u01/gateway/bin/dg4msql)

  )

  )

  Then please stop and restart the mssql listener and check again.

  -Klaus

• Help me configure bridged networking

  I just build a Dell 2950 to host three virtual servers on a production network. I installed VMWare Server 1.0.8 and have a virtual machine ready to go. The physical host that is running Windows Server 2003 R2 SP2 64-bit. The virtual host is the same except 32-bit. I have a second dedicated network adapter, I want to use for the virtual machine. I want the virtual machine to have a static IP address on my network of production, so I'm pretty sure that I need to use the bridged mode. The question that I have in fact is to configure interfaces. Configure the physical host with a static address with the virtual host with a static address? The virtual network editor DHCP service is used in this case? I disabled NAT as I did not need. Basically, in the virtual network editor I'm pointing VMnet2 on the second physical network adapter that I want to dedicate for the virtual machine.

  My network is 10.218.100.x\24 and I have a couple of addresses available for this. I have assigne.15 physical NIC host. I ai.16 par.20 available to use. Could someone provide a brief description of how I can configure the virtual network adapter to have one of these static addresses and be available on the production network?

  No reason to change how the physical host gets its IP address for this interface NIC physical - if DHCP is left, if static, leaving too.

  Treat your VM exactly as you would for any other physical PC on your network... If you have a DHCP server for this application/subnet field, then let it use DHCP; If this isn't the case, then set static - just as you would for any other real computer.

• point to point Bridge configuration

  Hello

  One of you have documents showing how to configure a bridge point to point with several VLANs? Basically, I am trying to achieve:

  VLAN 1,2,3-Switch--AP1200 ><>

  I found this document, explaining how to configure the VLAN.  http://Cisco.com/en/us/products/HW/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#vlanbr
  However, it doesn't explain anything about the configuration of the bridge itself. Any help would be appreciated.
  Thank you

  Example Configuration link bridges wireless point to point
  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml

• 32L4333DG TV - need help with configuring WLAN

  I bought a flat 32L4333DG of Toshiba, but cannot configure the wireless connection.
  Help me please.

  Message was edited: assignment has been translated

  What's the problem? Have you read the instructions in the manual how to connect WiFi TV?

  There are 3 different methods to configure the WLan configuration:

  _1) easy Setup (WPS) _
  + If the AP is WPS compatible, this method can be used. +
  + WPS is a standard of the industry, designed to facilitate the wireless LAN connection and security settings. WPS automatically configures all the wireless settings. +
  + NOTE: WEP encryption is perhaps not able to configure through easy implementation. +

  _2) assisted Setup (installation using notification s AP information) _
  + Name network, authentication and encryption are decided according to the information provided by the AP. You can manually set the security key. +
  + The security key must conform to these conditions: +.
  + TKIP/AES: ASCII 8-63 or 64 Hex characters +.
  + WEP: codes ASCII 13 5 or 10 or 26 Hex characters +.
  + There's a key ID to set for the WEP encryption. +

  _3 _) manual configuration (manual entry of all parameters)
  + Some types of encryption are only compatible with specific authentication types. +
  + When authentication is an open system, only WEP or none is compatible. +
  + When authentication is shared key, WEP is compatible. +
  + When authentication is WPA - PSK or WPA2-PSK, TKIP or AES is compatible. +

  + When the inconsistent authentication/encryption pairings are detected, a warning message will be displayed and no connection attempt will be until the conflict is resolved. +

  + There's a key ID to set for the WEP encryption. +

• Bridge configuration with comcast - need to change password

  Hello

  I have a NetGear R6300 I use in conjunction with my comcast router (router comcast serves as a bridge). I am able to access the router to comcast, but cannot access the netgear router. We use the netgear as thoughout the home wi - fi router because the comcast is so bad. I think someone may be connecting to our wi - fi and I need to change the password of the NetGear router, there is always the default password, so a factory reset will not help.

  Any suggestions on how to change the password?

  The default password should be "password" without the quotes. You can change the password after logging in.

• Photo of tasks - help w / Configuration for W530

  Hello world

  I look the W530 as my main computer for work and would like some advice on the ideal configuration.

  Main tasks:

  -Lightroom (heavy-duty)

  -Photoshop (use light-medium)

  -Internet browsing

  -Email

  The main components, sure I wonder are:

  1 processor

  The i7-3610QM will be sufficient for the image processing? Or it is better to spend more to get the i7 - 3520M or i7-3720QM?

  2. graphics card

  The K1000M will be enough for photo editing? Or is it an additional amount of $250 for the K2000M?

  3 memory
  These two options, is one favorite on the other?

  Kim,

  I am a professional photographer with a w520. I shoot captive and process/manage images with Lightroom and Photoshop 5.5. I took it that you had planned to order a unit and ask about options. Your needs of work and workflow can be very different from mine. I have rarely 900 images from a shoot that must be batched through a series of Lightroom presets. If this is the case, I also have a production machine in my office which is a RAM Ivy Bridge with an AMD over-pants GPU 16Gig office.

  First thought: I spec'ed multiple option sets, with sales of Lenovo spoke of three weeks, and then stumbled forward on pre-packaged configurations * in stock * to Tiger Direct and as much as $ 900-1000 less. Same unit! I don't have the files with me here to be absolutely sure that I'm naming figures of right of savings but look before press you the button on a Lenovo order.

  Secondly: I am happy with my speed with a 2720QM (think I have the right number), processor four hearts which is not the fastest MHz offered but had the four nuclei. I went with 8Gig and I think I put in place to take an another 8Gig if I needed. I find that Lightroom and same PS aren't as starved of RAM than I like! LR in particular is not accelerated with more RAM. But the speed is not as fast as the production machine, I mentioned, but that's OK.

  I did a little research that routines get discharged to the GPU by Adobe LR and PS code and now the support is somewhat limited. My hunch is that, apart from the true 3D and mechanical design community auxiliary Board 1000 NVIDIA is OK. There is a post here, "harrisb" through whose positions on GPU and CPU of the thoughts and surveys you should absolutely dig. I hope it sounds your choice of CPU.

  I called the screen of 1920 x 1080 'HD' and it has a very nice mast and I like it a lot. I have never put my own ColorMunki on that, but intend to do so. There are MANY complaints about the equipment of calibration color and sw included in those of certain configurations of the w520. Avoid. Buy the munki color with the money you save. More flexible tool as a separate purchase and the device. Others with color management skills more I have to comment here, please. There are a gamut lok more this unit even if the details of its manufacture would not point to perfection. Not IPS, for example? Search here in the forum to learn more. I manage has obtain the driver works correctly for my screen. It is supposed to be a dialog box control for 1000 nVidia CUDA routines that never appears in my device.

  Certainly intend to put an SSD in the unit. I went with the option of mSATA 80Gig Intel in November 2011 and will be placing a 256Gig unit Samsung 830 here next week. I use a Hitachi 750 drive in the Bay of HD now, which will place it in the optical Bay. I really need a disk of 1 TB at this stage. You can do it yourself. There are a lot of tips here on the forum.

  PM me your website and I will answer you. Love from Denver, was a photographer in the biz of skiing for a while.

  Good luck.

  jonathan7007

• Help text Configuration file reading

  Need help...

  I try to do a VI that will read a simple text configuration file.  The file will have entries like:

  URL = 192.168.0.1

  Port = 9000

  What I want to do is read the line and 'analyze' in 2 channels.  Then, based on the content of the first string (the part before the = sign), do something with the second part (after the =).

  I managed to open the file using "File open/create/replace" and but will have problems reading "Scan From File" to pull strings (it seems to define a mistake when I read in the first line, although my probes show that I had two channels).

  Anyway, once I have my 2 strings, it is a simple 'case' as the structure that I can use to search through all my "pre-defined first?

  Do not build something new. Just use the file Config screws - check under file IO functions. They will do exactly what you want.

  Mike...

• HP C4580 not scan to PC. I need help to configure my Netgear router please :)

  Hello

  I've read here, the threads that talk about this printer prints only not to or from a PC - my problem is that the C4580 go scan from my PC, but will not scan to PC.

  I found an answer from someone who has had the same problem earlier this year, but I do not understand what to do.

  Here's the answer:

  "I have ordered mine entering the settings from my router (Netgear) page and setting the built-in firewall rules. "The internal firewall was blocking the printer, I could print, scan using the computer, just could not scan from the printer to the computer.

  Also, I have a Netgear router, but could do with help on how to do the same thing as the person above.

  Thanks in advance for any help!

  Sorry, I don't need help after all

  It was not the router requires a configuration, it is the firewall that was a block that should be changed to "allow".

  My "all-in-one" now does everything it is supposed to do

• RE: router wrt310n - need help for configuring wireless security

  I can get wireless if the router is not secure, but cannot configure wpa and wireless security.  Instructions followed on linksys tutorial but still connect wirelessly if I select wpa security.   In addition, I can't find a way to change the ssid, the pages of router do not match documentation.  The version of my router is v1.  Is this obsolete, I know that there is a v2.  Any help will be appreciated.

  Please follow these steps to configure the wireless settings and try to connect to the wireless network.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Fix the Radio band to wide - 40 MHz and change the broad Channel 9 and channel Standard 11 - 2, 462 GHz... Wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  IF YOU ARE NOT ABLE TO CONNECT TO THE RADIO

• Need help to configure the VLAN on a powerconnect 5448

  Hello world

  I am currently working on 2 switches PowerConnect 5448 but I'm completely lost in configuring VLAN.

  My bow:

  

  My needs are:

  -J' have 2 different networks that need to be isolated in different VLANS

  -I want to port 11-14 to use for network backup, all others must be used for the production network.

  -This 2 networks must pass through the port 48 (fiber)

  How can I configure this kind of network on the powerconnect interface (or via telnet)?

  My understood are the following, I have to create 2 different VLAN tag all ports, switch to safe mode all ports of the entitlement each port to the VLAN voted. Am I wrong?

  How the fiber port?

  Thanks in advance for your help on this matter.

  Since your 2 VLAN need not communicate with each other, you should be able to get this working.

  The easiest way to do this would be to have your production on VLAN 1 and VLAN 2 second network.

  Assign an IP address to the switch with the command IP #.

  Assign a default gateway with the # ip default-gateway command.

  Create a VLAN 2:

  Database console (config) # vlan

  Console (config - vlan) # vlan 2

  Set 11-14 ports to access the mode for VLAN 2

  Console # switchport mode access

  Console # switchport access vlan 2

  Set 48 on trunk or general mode ports.

  Console # switchport mode Trunk

  console # permit trunk switchport vlan add 2

  You should get pretty close to a work environment. You may encounter some problem with VLAN 2 contacting 192.168.1.0, maybe just need to put it up and test.

  Here are a few links to software packages and manuals that can help.

  Firmware.

  http://Dell.to/1tz8tW0

  Manuals.

  http://Dell.to/1yqV4DJ

  Keep us on how will your configuration.

• Help to configure the router Cisco 1941

  Help!

  I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

  Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

  Help, please.

  Hello

  Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

  Configure the terminal

  username username privilege 15 secret PASSWORD

  IP http server

  local IP authentication

  Sent by Cisco Support technique iPad App

• Please help to configure the router for internet connection 871W!

  Hello world!

  I just started styding for CCNA, so I'm totally new to Cisco stuff. Recently bought a router 871W and spent two days in a row trying to configure internet connection with no luck! I use the port console for the configs and SDM/CCP. Would be greateful if someone could tell me how to do simple configs of internet connection. I googled everything but it's still confusing. I can't assing all-IP ports FA 0-3. I used instead of the VLAN. But all tutorials use FA0 and when I try to assign an IP address to FA0 it gives me some L2 cannot be assigned or something... :/ And I am also confused at what address IP use for WAN.

  I connected the cable between the Modem and the LAN of the PC port and copied some IP addresses which I think I have to use to configure the router for internet connection. And here they are:

  ISP IP: 76.114.54.255

  SUBNET: 255.255.248.0

  GATEWAY: 76.114.48.1

  DHCP: 69.252.97.4

  DNS: 75.75.75.75

  75.75.76.76

  If you can, please help! Thank you!

  Hi david,

  Looks like your 871w can not get a dynamic IP address: % unknown DHCP problem... No possible allocation

  you could ask your ISP to perform a reset/clear MAC add and try again?

  also, kindly post lastest "show run".

  Edit: just to see you've updated your screenshot. could you add command under 4

  Mac-add 0001.4af9.8b83