How to configure raid HP esx3.5 hosts?

Similar Questions

• How to configure the network between the host (Windows 8) and Guest (Linux)

  Hello

  I am trying to configure network between the host (Windows 8) and Guest (Linux). Guest on VMware Workstation 8.

  Using this network, I want to configure putty so that I can access comments linux to a PuTTY that is installed on the host (Windows 8).

  Thank you.

  Abdul

  To obtain external access to comments (access the guest from the host), you must configure the IP static within the guest (Linux) as below and restart the network (service network restart)

  eth0 is a dynamic IP (DHCP) to get wireless internet access

  eth1 is a static IP address

  

  

• Cannot configure RAID 10

  UCS C220 M3S with 2008 M - 8i SAS raid PCI mezzanine card

  We just got a new server wiith this controller when trying to configure it with four (04) disks to a Raid 10 SAS... OOHH no RAID 10 could choose.

  I found a paper that says that controllers RAID 10 support:

  Link:

  http://www.google.com.pe/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&ved=0CDkQFjAA&url=http%3A%2F%2Fwww.cisco.com%2Fen%2FUS%2Fdocs%2Funified_computing%2Fucs%2Fc%2Fhw%2FC220%2Finstall%2Fraid.pdf&ei=_JmDUt7QEZPesASeqYLwBg&usg=AFQjCNEDExxiAHNdoxdwcD6VcVYk-ZL_LA&bvm=bv.56343320,d.cWc

  Please know what happends.

  Thank you.

  William Z.

  Hi William,.

  How do you set up the raid volume? You use the WebBios utility?

  If you use the WebBios utility you must make sure that you create two spans of two disks of each to be able to see raid 10 in option.  See the document below, it will show you how to configure raid 10 beginning on page 76.

  http://www.LSI.com/downloads/public/MegaRAID%20Common%20Files/51530-00_RevF.PDF

• Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Hi stuckfree,

  The question you posted would be more appropriate on the TechNet Forums. I would recommend posting your request here.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

• How can I configure raid 1?

  I have a HP m9340f, and the 750 GB seagate drive that accompanies it is eventually died. Of course, I don't have any image or to clone, so now I have to re - install all my nonsense.

  In diagnosing the drive, I discovered that the bios has raid capability. In fact, that's what the reader has been set on (although there was still only 1 disc). I've never used raid, so my question is, if I want to configure raid 1, so that the next time a drive dies, I have a built-in backup, what exactly do I do? I know that I need to install 2 hard drives, but as soon as I did this, raid configure automatically? I don't see any special properties in the screens of the bios for raid, except for access to the drive (ide/raid/AHCI). Would this be a good idea to use seagate disks, or cares not the bios?

  Any help would be appreciated.

  Hello bassman952, maybe I can offer a glimpse of the Raid arrays. Many Members here know this already, but for those who do not, it seems that your system is capable of Raid. It has the Intel G33 chipset, where specifications for this chipset can be found here. This chipset includes the Raid feature for most Raid array configurations. However, HP changed the BIOS to only supported Bay Raid0 and Raid1. A Raid0 array consist usually of 2 hard drives and recommend that be of the same manufacturer, model, capacity, speed and cache. It is possible to use different brands and other specifications of the hard drive, but it is strongly discouraged. A Raid1 array also usually consist of 2 hard drives with the same configuration as described above. All Raid arrays must be installed before all the data is stored on the table.  To configure a matrix Raid on the chipset Intel, immediately after the HP Logo screen disappears, press ctrl and the I touch both and the Intel Matrix Raid Array utility will appear. You can then configure matrix Raid type and disk to be included in this table, save the configuration and exit. The table written Raid0 and bed for two drives at the same time, but with different data. This is referred to as a matrix of blocks. The Raid1 array is referred to as a network of mirrors. If one of the disks in Raid0 array were to fail, all data on both drives would be lost. The Raid1 array reads and writes the same data on two drives in the Raid array at the same time. If one of the disks were to fail, a new hard drive can be installed to replace the failed drive and the system booted and the Raid1 array will be rebuilt, which means that the data from the hard drive of existing work will be copied to the new hard disk. Depending on the capacity of the hard disk and the speed of the system, it can take a good amount of time to accomplish. After that the Raid1 array is rebuilt, the system should boot normally. Table of Raid0 is mainly used for performance while the Raid1 array is used mainly as a redundant to the first hard drive backup. If a Raid array is broken, which means that the configuration of the table is changed, all data on the hard disks will be lost, even in the Raid1 array. Can I have left some items, since I'm trying to remember this memory, but this is essentially how HP uses Raid arrays in their use of home systems. Others use Raid arrays that are different, such as Raid5 and Raid10, Raid0 + 1 and some other Raid configurations, but since we are talking about the Raid arrays on HP systems, other table Raid differences would be not useful for the discussion here.

• How to configure the CD driver on the host for a virtual machine?

  After you create a virture machine and put the CD of driver on host, when powered on the vertual machine, may not start the drive form the CD only from NIC.

  How to configure the CD driver on the host for a virtual machine?

  Right-click on the virtual computer and go to edit settings. Click the Options tab and under the tip list, there should be Boot Options. Enter an amount of milliseconds to wait before your boot, so you can activate the CD-ROM. You can also activate the CD even if it boots to the NETWORK card option, and then reset the virtual machine. Get the focus of this virtual machine on the console session, and then press ctrl-alt-insert. Your CD-ROM will stay connected if you do not want to delay the startup process.

• Help! Configuring multipath storage ESX3.5

  I have 5 VMFS Vdisks presented to my two ESX3.5 hosts SAN HP EVA4000 (two controllers, A and B).

  At the end of SAN, the configuration is:

  Vdisk	Disk group	RAID	Preferred access/mode path	Management controller
  san_vmfs1	FC 10 k	Vraid5	No preference		A
  san_vmfs2	FC 10 k	Vraid5	No preference		A
  san_vmfs3	FC 10 k	Vraid5	No preference		A
  san_vmfs4	FC 10 k	Vraid5	No preference		A
  san_vmfs5	FATA 7200	Vraid5	No preference		A

  controller A	WWN: 5000-1FE1-5007-9880	PORT1: 50001FE150079888
  		PORT2: 50001FE150079889
  controller B	WWN: 5000-1FE1-5007-9880	PORT1: 50001FE15007988C
  		PORT2: 50001FE15007988D

  My end of ESX host, the configuration is:

  	ESX1	ESX2	Device
  	preferred path	preferred path
  san_vmfs1	50001FE1 5007988D	50001FE1 50079889	vmhba1:0:1:1
  san_vmfs2	50001FE1 5007988D	50001FE1 50079889	vmhba1:0:5:1
  san_vmfs3	50001FE1 5007988D	50001FE1 50079889	vmhba1:0:9:1
  san_vmfs4	50001FE1 5007988D	50001FE1 50079889	vmhba1:0:13:1
  san_vmfs5	50001FE1 5007988D	50001FE1 50079889	vmhba1:0:14:1

  I use fixed to the management policy multichannel but way preferred as you can see. I wonder if it's a problem because my SAN controller event logs Gets the following logs all the time:

  "The event 4207001b; Indicates the virtual disk is passed to the property of the other controller HSV200.

  0310001f; A virtual disk in the storage system has changed master controller. »

  Your contribution is welcome. How to manage and distribute the workload between different virtual machines? We have heavy files, Exchange server and SQL server servers.

  Starting to make sense now, as I've never seen these errors in my controllers 3 months I was running on my san EVA, but I looked in the newspaper a few weeks after I upgraded my HP Agents (who at the same time, I restarted the ESX servers) and I noticed the errors.

  Thanks for the link!

  See you soon,.

  Brian

• How to configure das MD3200i load balancing

  I would like to connect a MD3200i (with two raid controllers) to one of our Windows 2003 R2 servers without the aid of a switch.

  After most of the documentation, some things remain pretty obscure to me. I'm new to MPIO/balancing and cannot figure how to set up.

  Is it possible to connect 1 nic host to RAID 0 and another host nic to RAID 1 and then combine the bandwidth? Thus having 2Gbs instead of 1Gbs? Or is it only a redundant path sollution, happening the other controller in case of failure of the first line. How can I configure this regarding the IP addresses, subnets. And where is the configuered to load balancing. This is explained in the documentation? I can't find it. I found a few examples that include the use of a switch, but none with das sollutions.

  What I have is 4 the MD3200i UTP cables to connect to the host. 2 the high raid controller and 2 on the lower raid controller. And use that I have 4x1Gbs, resulting a connection 4Gbs to a single partition on the MD3200i of load balancing.

  Thanks for any help.

  Multiple paths and in windows 2003 load balancing is managed by the driver MPIO is installed when you install the 'host' or 'full' version install MD Storage Manager. There is no need to separately aggregated network adapters to get the aggregate bandwidth. The pilot, by default, uses repetition alternated on all ports connected to a single controller.

  Also, for a single virtual disk, all i/o through a single controller and the second controller acts as a redundant path. So, if you have 2 x 1 Gbps connections to each controller, you will have, at most, 2 Gbps for each partition. Now, each controller can have virtual disks, so the second controller may have a second partition that will also have a separate between 2 x 1 Gbps connection.

  You can set IP addresses and subnets that are similar to the way that you would with a switch as long as you can test the connection port. It would be wise for each NETWORK card on the host on a different subnet and each port on the MD3200i on the corresponding subnet. This will make it easier when you set up your iSCSI.

  You can use the configuration utility to MD in place your iSCSI sessions too

  -Mohan

• How to configure ICS in network wired (Ethernet LAN) mixed (some XP some 7 64bits)

  We have an ethernet network.  A high speed printer.  Two towers XP (wireless).  A windows7 PC.  Currently, the windows7 pc is a laptop which has wireless capability.  However, we have NOT a wireless router. So don't give me responses bulletins on wireless connectivity.

  We use Internet connection sharing.  Somehow it just stopped working.  Do not know whether to blame a windows update or what.  We have probably messed up the worst configuration still try to get it working again. So I think that we must all start over and set up from ground zero.

  There is a technical bulletin, with simple (for beginners) instructions on how to configure ICS in a mixed network?  The instructions must be combined with the following configuration:

  Our host PC is XP.  We cannot change that, then give me all solutions where the pc windows7 is the host

  A customer is XP.

  A customer is windows7.

  We don't need to share files, just the printer.

  Hello

  The question you posted would be better suited in the technet Forums social. I recommend you to send your request in the below link:

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140

• Configuring RAID 0 without on a MCP61PM-HM restore disks

  I have a HP Pavilion Media Center m8300f desktop PC.

  I don't have restore disks... I don't see ANY option in the bios to RAID 0 configuration...

  How can I configure RAID 0 before installing Windows?

  I was able to get the job by finding a bios PIRATE/MODDED Raid0/scratches.

  For some reason any HP disabled raid in the bios that they provide.  Is not acceptable.

• How to configure the settings of mail on HP Laserjet Enterprise 500 color MFP M575 printer/scanner?

  How to configure the settings of mail on HP Laserjet Enterprise 500 color MFP M575 printer/scanner?  The Office has 5 staff members each with ending with [email protected] for example e-mail addresses.  We have also created an email for option analysis as [email protected] (not sure if creating an e-mail address for the scan option is required).  We are not part of any domain, and there is no server in the office.  When you try to configure the email on the printer/scanner control panel it asks the host name.

  What host name that I can use?

  If you try to configure the browser by using the IP address of the printer, he asks as the SMTP server. The MS Outlook 2010 all our emails use mail.junior - albania.org incoming mail server and outgoing.  Other settings in MS Outlook 2010 are box My outgoing server (SMTP) requires authentication checked and use the same settings as my mail server entering selected.  On the Advanced tab: incoming server (Pop3): 110 (SSL encryption is not checked) and outgoing (SMTP) server: 465 use the type of encrypted connection (SSL) following.

  What server SMTP should I use in this case?

  I would appreciate your help in the configuration of the HP printer/Scanner for scanning and sending by electronic mail to the members of the office staff email addresses.

  Thank you...

  I'll link you to the product page with several documents which I hope will help you to configure your e-mail settings. Please look through them and see which ones fit your needs:

  Scan and send (e-mail, send to folder, digital sending, etc..)

  Here is another site that has some videos that will guide you through the entire upward (here I would try everything first )

  Simulations of MFP - digital send

  If these don't work, please let me know and I will continue to search it for you.

• How to configure the network adapter when you run ESXi on VmWare workstation?

  How to configure the network card installing ESXi on VmWare workstation 6.0.0?

  These are the options: I tried bridged, host-only NAP.  None of them works

  

  What Miss me? driver or adapater?

  I'm running on vmware workstation on Windows 7 with Lenovo laptop.

  in the configuration of your virtual machine, the main issue is memory. you gave the 2 GB of RAM, whereas ESXi 6 cannot go forward without minimum 4 GB of RAM.

  If please have 4 GB of RAM and re-run Setup. you will get through.

  message about the network card should also not appear after that. What kind of network you choose depends on your need.

• How to configure a secure https payment page?

  How to configure a secure https payment page?

  Hello Gregfitzmiami,

  This part is done on your hosting server. Please see the links below which explains more in this regard.

  https://support.Microsoft.com/en-us/KB/324069

  How to get HTTPS: Configure SSL on your website - Expert Guides

  Kind regards

  Vivek

• How to check the NUMA on ESXi host node

  Dear team,

  I have cisco ucs Server Blade configuration below b - 200 m3. I want to know how to check the NUMA on ESXi host node.

  RAM: 192

  Socket 2 (8 cores).

  concerning

  Mr. VMware

  Unfortunately, it seems THAT NUMA is disabled hardware wise. You can only activate it via the BIOS setting.