HP C4680 transport Jam, part discount

HP Photosmart C4680, printer/scanner/copier. After completing a piece of printing, the printer said suddenly have a carriage jam... When I pulled the paper from the feed, a metal cylinder of small (approximately 1/4 "long) came out too. The cartridges now moving in or out of the right-hand Dock except manually. I searched but found no user information that goes into that kind of detail. Is this a problem user-serivceable? Can it be fixed? Or I have to replace an old printer about 18 months?

Thanks for any help.

Unfortunately, this is not a non repairable part. If you have an extended warranty that needs to be covered.

Tags: HP Printers

Similar Questions

  • Photosmart 2575: eprint causes transport jam

    My Photosmart 2575 printer can print the self-test and Windows, but most of the time when I use eprint to android, either phone or tablet, it loads the document and then reports the transport jam. It almost seems like eprint sends a command to the printer is not exoecting. How can I fix?

    Hello

    The HP Photosmart 2570 series is not supported by the HP ePrint software, so you may experience problems.

    You can find the following table with web solutions offered for any model of HP printer, HP ePrint is not supported for your printer:

    http://support.HP.com/RS-en/document/c03722645

    I suggest trying the HP Print Service Plugin that seems to support your printer and check differences using this solution:

    http://support.HP.com/RS-en/document/c04024231

    Kind regards

    Shlomi

  • OfficeJet 4620 - stall of transport: transport Jam

    HP Officejet 4620 error: transport Jam. The print cartridge will not move...

    I get this error message, and the printer does not work.

    I watched the video of support, and there is no paper stuck or blocked anywhere, or any obstacle that I can find. I unplugged the printer, etc., as suggested. I can't always the printer to work. The carriage move not left by itself when I open the lid. I heard a noise of rattling after printing... I know that the video States if all else fails it may need service. But I was just wondering if there may be a few other simple fix, I forgot? The White Ribbon seems intact at both ends. The transport does not seem to move at all. I pull it to the left, and he stayed there after the closing and reopening of the coverage. I also removed all cartridges and reinstalled them.

    I called technical support... a new printer is shipped to me... thanks...

  • Warning of Photosmart 5524 transport jam not clear paper jam

    My HP Photosmart 5524 seems to be in perfect working order but I can't move it beyond the 'Transport Jam' warning on screen.

    Have followed all the steps on the screen of the printer and the HP Web site.

    Mac OS x

    Running wireless printer.

    Thanks for any help.

    Hello @And1234 , welcome to the forums

    Check out the guide I posted below. If you have already tried all of the steps, please consider contacting HP directly to inquire about a replacement printer or a trade in option.

    A 'Transport Jam' Message displays for HP Photosmart 5520 e-all-in-one and HP Deskjet Ink Advantage 5520 e-all-in-One Printer Series

    Details of HP:
    If you call in North America, the number is 1-800-474-6836 and if you call outside the United States / Canada: click here.

    Best wishes

  • HP Officejet 7310 transport Jam

    I tried all the recommended solutions and still cannot get it printed, he tries, but then I get the error message

    Jam of transport

    Door open, clear transport jame and then press OK to continue.

    Hello

    Please check if there is no paper stuck near the transport area. If found remove it.

    Also, check if you are able to manually move the carriage.

    If the truck moves automatically / manually, then we might have to reset the printer. Therefore, check your Inbox for the steps to perform the reset.

    If the transport does not move, the printer must be repaired.

  • HP Envy 4500 ~ transport Jam

    I just bought this printer. I'm trying to install it. I'm stuck after installing cartridges. The display shows 'transport Jam. The printer carriage cannot move... "I see no visible obstacles. I have taken the cartridges out and reinstalled several times. I unplugged and plugged the power cord several times for different durations. I'm about to make it. Help, please!

    My son came home and fixed my problem. I had to start him early, and he's got to work. Thanks for your help.

  • transport jam message deskjet3052A

    receive message carriage jam, but have no jam, power light flashing.

    Here is a link that can help you with the transport jam.
    http://goo.GL/oL45u

    I hope this helps.

  • My printer gives me the message 'transport jam'... open door, clear jam and press OK

    HP Officejet 6300 all-in-one

    Mac OS X Snow Leopard

    message: 'transport jam'... open door, clear jam and press OK

    Sometimes, I have to do this many times before it will work.

    Hello

    This article should cover the problem you are experiencing. Give the steps described a shot and tell us if it helps.

    Good luck!

  • HP 6500 has more transport Jam

    I have a HP 6500 has more printer that has stop working.  Appears on the printer 'Transport Jam'.  I search the web and find videos that have troubleshooting steps to correct this problem, but they have not been of any help.

    When I turn on the printer, I hear a clicking sound until the "Carriage jam" message appears on the printer screen.  The print carriage is stuck on the right side of the printer and will not move.

    Any ideas?

    I'm sorry that you are having this problem with the printer. Here a link to a document from HP that addresses transportation for your model of printer jams. It will give you the troubleshooting steps that should be taken to resolve the issue you are experiencing with the printer.

    If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

    HP Technical Support call case form:
    http://goo.GL/w7Hgh

  • transport jam f on Officejet 6310xi all-in-one printer

    I use an all-in-one HP Officejet 6310xi priniter.  I send the print command and when prinited sheet is delivered first four lines or are so prinitinig that half of the line and the message thenrerst prints OK.  However, after the delivery of the printed sheet I get message, "Transport jam" I received instruction of "open the door.  Clear jam and then press 'OK '.  How can I stop this from happening?  My operating system is Windows 7.

    Have you removed all paper from the input tray and shined a flashlight upwards in the status bar to ensure there is nothing caught in the rollers?  Remove the duplexer/rear access door and make sure that there is nothing in the rollers at the back.

    I would also check the printer.  The top and look down inside the right-hand side of the printer (right side of the carriage house).  Do you not see any paper into a ball in this section?

    There is also a document with steps to help fix a carriage jam in an Officejet 6310xi.  The document can be found here.  Let me know how it goes.

  • HP 7310 transport jam becomes jammed traffic!

    I have a HP7310 all-in-One and a Windows 7 PC, which works well for a few years and just got the error message "Carriage jam" feared after a weakest page. I followed the instructions HP release of this http://support.hp.com/us-en/document/c00042632, including the replacement of the ink cartridges online.  Following the instructions, I moved to the Middle transportation (where he stopped when the original error has occurred) on the right side of the machine and cleaned gently from the machine.  Transport is now stuck on the right - she will go only left about an inch or so and of course the transport Jam message is there. I read in some forums on this site that there is no non repairable this possible repair, but on a further mention of sites of the means to free transport. I liked my 7310 HP - if there is anything that I can try to free transport and clear the carriage jam error, would be very grateful to the community of HP. Thank you!

    If you can't find any debris locking trolley in place, then I, unfortunately, can't unlocked transport. I don't know of a workaround to allow you to manually unlock the transport if it is blocked.

    You can consider replacing this printer.

  • 'transport jam' paperless in the officejet pro 8500 printer

    I received a fax and then "clean printhead" appeared... 15 minutes later... always cleaning... I shut it off with the power button... waited 2 minutes and then turned back on it... "jam carriage error", I check the whole printer inside out and backwards on the side... I turned it off again... unplugged it... and rekindled it... then I saw "replace ink cartridge"... the cyan and black... I took the cartridges off... put them back in and then looked at the ink level... There are still many at a time... then I get the "jam carriage error" once again... and nothing that I may change this in the window... If I click OK in the window... it says "Printing cancelled... then back to 'jam carriage error'... I think» also the transport of ink is pasted on the right side... He tried to pass it... and cannot without ripping it out of the printer... when I opened the box in the back... it was ink on the right side...

    It is 3-4 years, because I had it... and put some miles on it... I do PITCH it... just bought the 8600... still in the box... or is there hope... and of course, I just bought and put new cartridges color... lol... Thank you...

    I count on the printer immediately.  It may be just a deep reset to clear the problem.  Run through this document.  If it doesn't help you to solve the problem, then go ahead and get rid of the printer.  Let me know what happens.

  • Transport jam 6520

    Hello

    I bought my wife a new printer HP 6520 for Christmas.

    I tried to put in place today, unpacked, installed the cartridges and then got the error message "clear carriage jam".

    I tried to do the hard reset and also follow the instructions in previous posts on this subject several times, and still, this has not solved the problem.

    Please can you advise of any new idea of troubleshooting I could do with this work for my University wifes work as soon as possible.

    Thank you very much

    Stu

    I managed to solve the problem. With the 4 link tracking solution, posts in cartridge parking blocking transport.
    http://support.HP.com/us-en/document/c03369132
    Thank you

  • Transportation jams, always on the left side, always 3/4 this page

    Printer HP all-in-one HP Envy 110

    Jams of transport, always on the left side, always about 3/4 per page

    Hello Radians,

    I don't think that the router would be the question, unless you have more than 20' away from the printer.  This would cause a sporadic connection.  Regarding the shaking or any question relating to a question of power, the only thing I can suggest is to make sure that the printer power cable connected directly to a wall outlet and NOT a bar/power strip.

    If you still have questions, please use the contact information to get suggestions from HP Total Care.

    Thanks again for your time.

  • HP photosmart c4280 issue transport jam

    Tried the hard reset as suggested, still getting the same message. "Jam, jam clear transport transport. Press OK. Any suggestions? Like new, used one summer in my truck. Cheaper to buy a new one and it crash?

    There are a few things I would do in this case.  I remove all paper from the paper tray and make sure that it is no that whatever it is taken in the rollers that would block the way of transport.  Also, look inside the printer on the right side of the cart and make sure there is nothing blocking the movement of the cart here.

    Have you tried to raise transportation and trying to move gently by hand?  Can it go all the way to the left and all the way into the printer?

    There is also a document with more troubleshooting for a jam carriage found here.

    If all the troubleshooting steps are carried out and the error continues to be present on the screen of the printer, then the next step will be the replacement of the product.  If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

    Technical Support case HP formula call: https://h10025.www1.hp.com/ewfrf/wc/phoneInput?cc=us&dlc=en&lc=en&product=5061082

Maybe you are looking for

  • Question about hidden Partition Recovery

    Hi readers, Bought Satellite Pro A200 last Nov. I am looking for what is called hidden Hidden 1.5 GB partition. I thought he would have shown in disk management. I started pressing F8 for advanced boot options, as the manual says, the repair option i

  • Printing/scanning HP 403 error

    My challenge seems to be well noted by others... tried to restart my entire system... Please send secret instructions. Thank you.

  • Uknown /RA Media Server administrator password

    I've never set up an administrator password and now when I try to download something it appears with 'RA Media Server', then a space for a password, I don't know. To this effect, I can't download anything and Dell was no help because my warranty has

  • Windows Vista, will not let me install the software! follow-up of the steps and nothing

    I tried to solve this problem for some time now with no results, I searched online and nothing. all the programs I try to install start and acts like it will install but never finished or shows me the error message. I turned to (UAC) and nothing. tri

  • New simulator facility does not

    I installed the 2.1.0 - beta1 NDK earlier. Also installed the Simulator. When I launch the IDE and you try to run a sample project, he asks me the IP address and the password for the Simulator. I don't see how to launch the Simulator. I use Mac OS X