HP Photosmart 5512 disconnection of the wireless network

Similar Questions

• Photosmart C4599 connects to the wireless network

  System details: Windows 7 64 bit, HP Photosmart C4599 Limited Edition. Wireless network (Netgear router) with visible SSID and MAC filter.

  As the title suggests: my wireless printer is not connecting to my wireless network more. The reason that it is 'more' is because he used to work. But my wireless router has started to lose the internet connection - and I read somewhere that it might work to change the broadcast channel of the router (instead of channel 11 to 13). And it helped.
  But since then, the printer was not able to connect. I tried it back - and interruption of the internet connection but the printer worked (a little).

  I tell myself that I have to reset the wireless printers Setup, I don't know how to do.

  Ok.  I think that the issue would be with the channel.  It might be too high a frequency for the printer to communicate properly.  You can have a heavy traffic on any channel, it depends on what is around you.  I recommend trying channel 1 or 6.  You should be able to download a parser for your smart phone wifi see what are the channels have less useage.

• Photosmart C6180 cannot detect the wireless network

  I have a Photosmart C6180 for over a year, and until recently it connected wireless very well.  But since a week ago, it can't detect the wireless network.  I turned off the printer and wireless router several times each without success.  The "Wireless Setup Wizard" running on the C6180does not help. Watch simply screen printer "looking for... wireless router. "indefinitely, until the function Cancel.  The wireless router is about four feet from the printer, in a direct line of sight.  In addition, I have wireless Internet access using the same router and continue to do this successfully, then the router itself works.  Recently I have updated the firmware on the router as well (after the beginning of this problem).  Running the network Test report wireless on a 'PASS' C6180 returns for "Radio on" but a "FAILURE" for "use of Radio". The radio broadcasts as "about" section of the Menu Radio wireless network.  My router is a Belkin Wireless G Router model F5D7230-4.  The printer prints very well with a wired connection, but wireless connectivity has been a key reason behind my purchase.  Any suggestions greatly appreciated.

  Sorry, but your wireless radio is dead.  Its time for a new printer.

• HP Photosmart Plus connects to the wireless network

  I'm trying to connect my HP Photosmart Plus B209A to my wireless network. My wireless router doesn't have the WPS ability to connect. When you print the worksheet diagnosis network radio printer seems to work fine as it recognises my network and my neighbours networks 3 being active. When I try to connect to a network by using the menu from the home screen of the printer wireless says no connection available. Troubleshooting suggest not having your router wireless near a wireless phone, so I put the printer directly next to the router and still no detection. I would have just thought that the wireless radio was broken, if it wasn't for the network diagnostic worksheet. The wireless router is also Verizon FiOS one. Thanks for your help!

  Hi rachorn,

  I see you are having some problems connecting to your network of your HP Photosmart Plus wireless. You use a FiOS router, but installation is not able to see your wireless printer. You have a solid blue light on the front of the printer, what is the IP on the diagnostic page you printed and it says connected?

  I would like you to take a look here: the printer is not found during Setup wireless network in Windows. This document will guide you through the implementation of the IP address manually, please follow all the steps listed. I also recommend moving the router over 4 ' and less than 20 feet of the printer as having close can cause communication problems.

  If after all troubleshooting steps have been completed and you are unable to connect the printer to your wireless network, you may need to contact your router provider and have them open some ports that can block a successful installation.

  Reply with the information requested, I'll watch for your reply.

  Thank you

• HP PhotoSmart restricted 6525 in the wireless network connection

  Hello

  I need to connect my HP PhotoSmart 6525 to a wireless network in my college dorm room.  IT supports the University has published the requirements for the connection to the restricted network and attention that many printers cannot. I looked on the HP website to see if my printer supports the protocols required, but information HP provides on the website is not detailed enough to tell.  I hope that someone on the forum can help me.

  Here are the requirements of universities to connect to the restricted network:

  ----------------------------

  • A device with a Wi - Fi adapter capable of 802.11 g, 802. 11A or 802.11n

    Note: 802. 11 b-only devices are not supported

  • To enable DHCP (Dynamic Host Configuration Protocol) to obtain IP configuration information

  • Operating system and drivers that support:
    • authentication of 802. 1 x (also commonly referred to as WPA-Enterprise or WPA2-Enterprise)
    • WPA2-AES (preferred) or WPA-TKIP
    • EAP-PEAPv0 (external auth) / MSCHAPv2 (internal auth) or EAP-TTLS (external auth) / MSCHAPv2 (inner auth)

  All connections to the campus network, no matter what either wired or wireless, must also bear the following (which are installed and enabled by default on modern operating systems):

  • IPv4 (Internet Protocol version 4)
  • TCP (Transmission Control Protocol)
  • UDP (User Datagram Protocol)
  • ICMP (Internet Control Message Protocol)

  ----------------------------

  Does anyone know if the HP PhotoSmart 6525 meets these requirements?  For example, he says "PEAPv0(outer auth)/EAP-MSCHAPv2 (internal auth)" or "EAP-TTLS(outer auth)/MSCHAPv2(inner auth)?

  Thanks in advance,

  Paul2

  "I could check on the web site of www.wi-fi.org HP Photosmart 6520 series is approved for"WPA-Personal"and"WPA2-Personal"and _not_ certified for" ' WPA-Enterprise and WPA2-Enterprise.  The Enterprise versions require the device to authenticate with a username and password, while the personal versions are not.  I also talked to the school, IT supports and independently, they have said that the problem with the help of authentication printers more is that you can not provide a user name and password.  Given that I could check with two sources independently, according to me, the definitive answer is that I can't use the printer with wireless network from business school.

• HP Photosmart 7520 unable to find the wireless network

  Printer: HP Photosmart 7520 e - ALL - IN - ONE SERIES

  Router: NETGEAR router WNDR4000

  Hi all

  After receiving our new HP all in one printer, we have found our network wireless networks list wireless during the printer set up. We are able to receive the networks of our neighbors, but not our network.

  We tried:

  • Using the WPS function on the router and the printer
  • Establishment of an open on our router wireless network
  • Connect to our wireless router using the setting on our laptop when the option during the installation of a PC.

  Any help on this subjest would be appreciated.

  Best regards, Nick van der Lee

  Hello

  I found the problem that was the printer not to see the SSID of the router.

  The wireless channel was on channel 12 for the frequency of 2.4 GHz. While I was looking around I found this Support Page for Nintedo. Point 6 is a mention about these channels with respect to the same problems I was experiencing with the printer.

  By changing our channel to channel number 3 number, we could see the wireless network.

  It's a bit weird because I thought that the printer has a full specification b/g/n but apparently not?

  In any case thank you for your support.

• HP Photosmart B109: cannot connect the printer to the wireless network

  I have some setting wrong my printer for wireless printing. It has worked well in the past, but with my new macbook air - this isn't.

  I can't access the function where to add the printer to the wireless network (my router does not support WPS so his password WPA).

  I remember setting this up on a PC - easy with the driver provided by HP, but on the Mac, the configuration tool does not appear to be a function where I add the printer to the wireless network - and HP did not provide a driver, because it is supposed to work with the mac built-in software.

  The manual says only: "follow the instructions on the screen", but the printer does not have instructions on how to connect - on-screen tests, only that it is connected...

  Anyone who knows how to add the printer to a wireless network?

  Hello @Joahkim!

  Welcome to the HP community!

  I understand that you have a problem to set up all-in-one printer wireless HP Photosmart (B109n) with your new MacBook Air OS x 10.10. I want to help you with this.

  Have you changed your router or your password since the MacBook Air? If this is not the case, your printer can still be connected to the network and the trickiest part of that place will be done for us already.

  We will print a Network Configuration report to see if it is connected:

  • On the Control Panel, press the button next to Scan. The Scan/Wireless menu.

• B110A connects to the wireless network but no PC connection

  Hi Forum,

  I just bought a new HP Photosmart B110A printer range. I got set up with my Belkin wireless router. It is successfully connected. I could set up printing webservice as well. The printer is offline and I could also print a document by sending an email to the email address for the printer configuration. This means that the printer is connected to the wireless network and the internet.

  However, I can not connect to this printer from my PC connected to the same wireless netwrok. When I open the HP Solution Center, it displays the message "disconnected wireless.

  When I connect the printer via USB cable, I am able to connect to the PC and impressions as well fire.

  Can anyone help please?

  Kind regards

  Amol

  Download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&jumpid=ex_r4155/en/hho/ipg/forum/network_diag/

  What did he say?

• Connection printer HP Photosmart C4500-serieis to the wireless router.

  I had to reset my router and in so doing, he has changed the SSID and I had to change the password.  My laptop is connected to the wireless router, but my HP Photosmart C4500 printer does not recognize the change. How to re - setup the printer with the new information.  I tried all the wifi settings available on the printer with no luck?

  I have run the wireless network test report and he has failed in trying to recognize the SSID

  Thank you

  Hi you two,
  
  I recommend you try printing HP and doctor Scan. It's a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity. Click on the link below for more information on how to download and run the tool:
  
  http://goo.GL/QsIAx

• HP envy laptop laptop 15-ah150na: loses the connection to the wireless network device I had not only portable for 2 days

  Loses the connection to the wireless network sometimes directly after that the computer is turned on at other times after 5 min and sometimes after an hour.  No other device I have loses the connection to the wireless network.  Help, please.

  Hello @fairgame,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I understand that you have a problem with the WiFi and wanted to help you!

  First of all, try to review the next steps, offered by community member @Great-Christine-Tree:

  First of all, we have a step by step guide to guide you through the process of diagnosis here:

  HP PC - troubleshooting Internet and wireless network

  A second option is to try the following steps:
  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.

  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.

  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.

  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• How to get two laptops to access the wireless network.

  My chip wireless on a Dell Inspiron 1520 laptop (intel pro wireless 3954bg) can find the wireless network if I use Intel Pro software, but Windows cannot find the wireless network. My real growth problem trying to connect a second computer; an IBM T42 think Pad computer to the wireless network, but I get a message that the network is secure, and the second computer keeps trying to acquire an address, but will not acquire an address. He just continues to try to acquire again and again, he can never acquire it. This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then, the IBM laptop cannot acquire an address. I go around and try to understand it. Someone at - it information to solve this problem? Both computers are runing Windows XP Pro SP3. My wireless router is a Belkin54g (F5D7230-4V8000)

  Thanks for any help,

  Btk (billy the kid)

  You can control a with either wireless network adapter software integrated in Windows XP (or WZC Wireless Zero Configuration) or with software provided by the manufacturer of the card (for example, Intel PROSet/Wireless), but not both at the same time.

  Most, but not all, software configuration wireless no Windows is smart enough to disable WZC automatically.

  There are a few sites that offer "safety tips" for wireless networks which includes 'hide' your wireless network by disabling the SSID broadcast.  This is not a good idea and does not, in fact, your wireless security.  See http://blogs.technet.com/b/steriley/archive/2007/10/16/myth-vs-reality-wireless-ssids.aspx if you have disabled broadcast SSID of your router, automatic configuration won't be able to find it.

  I get a message that the network is secure, and the second computer guard trying to acquire an address, but will not acquire an address

  If you have enabled encryption wireless router (a very good idea), you will need to enter the correct password in order to connect a find an IP address. What type of wireless encryption configured on the router?

  This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then the IBM laptop cannot acquire an address.

  You have changed something else.  The idea of a wireless network is to allow multiple computers to connect; connection to a computer shouldn't affect how another computer connects.

  The easiest way is to configure your router to connect a computer using an Ethernet cable (if you connect wireless, you will be disconnected when you make a change to the configuration of the router wireless).  For the Belkin router User Guide is here--> http://cache-www.belkin.com/support/dl/p74559-f_f5d7230-4v8xxx_manual.pdf

  Open a web browser (Internet Explorer, Firefox, etc.) and type 192.168.2.1 in the address box.  You should get to the home page of the router. Click on the "Login" link at the top.  The default password for the router is blank (no password) unless you changed it.

  Click on the link "Channel and SSID" under the heading "wireless" on the left side of the page.

  • Make sure that there is to check the "Broadcast SSID"
  • "Wireless mode" should be "g only" or "fashion g and b" (the latter is necessary only if you have a very old b wireless adapter in one of your computers)
  • I suggest you let off QoS (but click on "more info" or see what says the User Guide)
  • The wireless channel should be 1, 6 or 11.  If you have no difficulties, let him you will find
  • "Protected mode" should be off (but click on "more info" or see what says the User Guide)
  • If you make changes, click on "Apply Changes".

  Click on the 'Security' line under the heading "wireless".  You should be able to see both what type (if any) encryption is configured (64-bit WEP, 128-bit WEP, WPA, or WPA2) and the password (if any).  Unless your computer maps are old, you should use WPA2.  If the adapter in one or more of your computers is too old to be capable of WPA2, use WPA.  Regardless of the bit, WEP length, is easily broken.

• My PC is connected to the wireless network, but it is impossible to open any internet page. I went through the diagnosis of Internet Explorer, see below.

  Diagnosis of last run time: 28/01/12 10:16:32 Gateway diagnosis

  Entry door

  Info the following proxy configuration is used by IE: automatically detect settings: enabled Automatic Configuration Script: Proxy Server: Proxy bypass list:

  info could not get the proxy settings via the Proxy Automatic Configuration mechanism

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  repair automatic action: reset the network connection

  action to disable the network card

  activation of the card network action

  successfully activated information network adapter

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  user redirection of information in support of the appeal

  IP layer diagnostic

  Corrupted IP routing table

  prevent the default route is missing or not valid

  Invalid entries in the ARP cache

  action cache ARP has been emptied

  Diagnosis of IP Configuration

  Invalid IP address

  detected info valid IP address: 192.168.0.1

  Wireless diagnosis

  Wireless - Service disabled

  Wireless - user SSID

  required user input action: specify the name of the network or the SSID

  Wireless - first installation

  Info the name of the wireless network (SSID) to which the user wants to connect is IrinaLaptop-router.

  Wireless - Radio

  detected info valid IP address: 192.168.0.1

  Wireless - off limits

  Wireless - hardware problem

  Wireless - Novice user

  Wireless - network Ad - hoc

  Wireless - less preferred

  Wireless - 802. 1 active x

  Wireless - Configuration mismatch

  Wireless - low SNR

  WinSock diagnostic

  WinSock status

  info all base service provider entries are present in the Winsock Catalog.

  channels of information the Winsock Service provider are valid.

  Info entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.

  Info entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.

  Info entry RSVP UDP Service Provider provider passed the loopback communication test.

  Info entry RSVP TCP Service Provider provider passed the loopback communication test.

  Info connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter

  Network location detection

  Info to help home Internet connection

  Identification of network adapter

  Info network connection: name = connection to the LAN, device = Broadcom 440 x 10/100 Integrated Controller, MediaType = LAN, type = LAN

  Info network connection: name = wireless network connection, Device = Intel (R) PRO/Wireless 3945ABG Network Connection, MediaType = LAN, type = Wireless

  Info network connection: name = 1394 connection, device = 1394 Net Adapter, MediaType = LAN, type = 1394

  Info network connection: name = connection high speed, device = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info network connection: name = blank, peripheral = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info both Ethernet connections and wireless available, ask the user for selection

  required user input action: select network connection

  Info Wireless connection selected

  State of the network adapter

  Info network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn HTTP: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn HTTP: error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  WARN FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  WARN FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  error could not make an HTTP connection.

  error could not make an HTTPS connection.

  error could not make an FTP connection.

  I did not want to do this (restore point). However, I found a solution. It comes: http://forums.techguy.org/networking/1029348-network-connection-status-media-disconnected.html

  Where there are two crucial steps (do not know if the two were needed) RUN command (1) netsh int ip reset reset.log and (2) netsh winsock reset catalog
  
  
  After a restart, hey presto my wireless connection was repaired. This seems useful, but not essential (shows wireless performance but not the solution): http://wpc.475a.edgecastcdn.net/0047...etup.1.2.0.exe which is run Xirrus Wi-Fi Inspector 
  Thanks for your time!
  Good bye

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional

• Router E4200, cannot secure the wireless network

  When my E4200 wireless network appears on a discovery list of wireless networks, there a padlock beside him in devices (like my Xbox and iPhone) that who would use to show that it is a wireless network, requiring a password. When I use my Xbox to connect wireless now, he said: "you connect to an unsecured network. Are you sure you want to continue? »

  I used the web portal to select 'Factory Reset' of my router. I also told my iPhone to forget and not automatically connect wireless network. After factory reset, I went to the configuration section of the web page wireless network access router, put a new name for the wireless network, personal WPA2 enabled for 2.4 and 5 GHz networks, developed a completely new password for two I had never used before and then looked for the network on my iPhone. I chose it and it connected right away without asking for a password. Still once, the network does not appear with a padlock next to him in the list of devices to the network from my iPhone WiFi and my XBox says always that this is an unsecured network.

  When using my internet browser to access router, WiFi networks are both classified as WPA2 Personal and each has a password in the password box (and Yes, I recorded the changes - that's what it shows even if I disconnect and then reconnect to the router access.) I tried to remove the power cord for 30 seconds and plug in again and there is no change.

  It's quite a recent change, like maybe the last week or more. I don't know if there was a firmware update or what - my router is configured for auto updates and when I click to check the latest updates, it says that there are no more updates available.

  TL; Dr: said access my router my wireless security is turned on. None of my wireless devices see as secure WiFi networks and each of them can connect without having to type a password.

  Do a reset factory and set up from scratch.

  If this fails, try this:

  Manually download the FW file to the local office of PCs.
  Reset the router, use IE or FF with all security disabled add-ons, load the FW file and let you treat.
  Factory reset the router once more and set up from scratch.

• 4 iPad unable to detect the C4599 already connected to the wireless network printer

  Hi all, I have a C4599 All in One Printer. I have just set up successfully with a WiFi connection to my router / modem network (infrastructure mode). There is no error message and I can print from a variety of laptops Windows (XP, Vista and 7). I loaded the HP eprint app on my Ipad 4 but it can not detect the printer. Note that the HP site says that this printer is compatible with the App ePrint.

  A second and possibly related is that I recorded with the HP eprint service website but I can't get the code or e-mail address for my printer. I can't find any way to turn it on the Web Services on the printer? (The HP site says this should be under Setup > wireless to the printer, but it is not.) There are only options to turn on/off the wireless, testing the wireless and print the wireless network and printer settings (which are all OK > PASS or information).

  Any ideas?

  Thank you

  With the update that has been done to the ePrint application, some of the old printers lost the ability to use this application to print from. The printer would not print directly from the iPad to the printer either. This is a feature called AirPrint. When you have the possibility to use AirPrint, he must place the unit on the same network as the printer, pull up a photo, press the action button on the iPad and then select print. The iPad will then give an option of the printer to print from if there is more than one printer capable of of AirPrint on the network.

  The printer cannot produce a code to register and save ePrint due to the age of the printer. Printers that have the ability of ePrint are a majority of those who have been in production in 2010 and later versions. A few Photosmarts who have the ability to use ePrint AirPrint are the 7520,6520 and the 5520. To learn more about these printers, see this link here.