HP Photosmart C7280 Auto Document Feeder mechanism stuck in the open position

Similar Questions

• LasarJet Pro MFP M226, M225: Tray is stuck in the open position

  Tray is stuck in the open position. When you print a copy, has had a paper jam. Open the lid and jam cleared, but cover will not close. I get a slight noise to slam, but do not use any pressure. Is there a version any?

  Hello @Liberty76and welcome to the Forums of HP!

  I'd love to help you with your Laserjet Printer. I understand the feed from the ADF tray is stuck in the open position and you are afraid to break if you use too much pressure. I suggest to use the following document to ensure there is no pieces of paper inside preventing them from closing: HP LaserJet Pro MFP M225 and M226 Printer Series - a "Document Feeder Mispick" Message appears on the control panel and the ADF is not Pick Up paper, feeds on several Pages or jams.

  If nothing is blocking the closing plate you need to expand the more open plateau then try close.

  Please mark your post as solved by clicking on the accept as Solution below if this solves the problem. If there is anything else I can do to help let me know. Thank you.

• HP Ps 309 a ADF (automatic document feeder) is good until the last page (copy, fax, scan) food

  ADF (automatic document feeder) is good until the last page (copy, fax, scan) food.

  The last page will scan, copy or fax.  But the charger will not expel the last page completely out of the feeder.  The last page will be halfway on the bottom of the feeder.  I searched this site and a few others and can't locate an answer.  I have seen the centre solution and also files with no joy help...  Help please.

  Try the reset in 'step 4' of this document:

  Reset

• Printing problems with XP and Lexmark-documents are just stuck in the print queue

  Original title: printing problems with XP and Lexmark

  Until yesterday, I was able to print OK using Windows XP and a Lexmark Printer series 3500-4500 with wireless capabilities.  Reported network test wireless (on printer) and report indicates that there are no reported problem, also did the diagnostic test and which shows no problem either.  I can't print and documents are just stuck in the print queue - please can someone help, it drives me crazy because it's probably a very simple solution.

  I guess you do not have all of the error messages.

  It is possible that comes to mind that your printer has received a new IP address of your router (this could easily happen if you have several computers and other devices that connect to your wireless network).

  Find the IP address of the printer of his network diagnostic page.
  Click Start > printers and faxes, right-click the printer and select Properties
  Select the Ports tab, then click on the button "Configure Port" (be careful NOT to click anywhere in the list of ports)
  Make sure that the IP address in 'Port settings' is identical to that shown on the diagnosis of your network printer page.

  To avoid this problem in the future, you must configure the printer to have a static IP address.  See your printer User Guide for instructions.

  Choose an appropriate subnet address (i.e., has the first 3 groups of numbers the same as the other addresses in your network) but who is not in the range of addresses assigned by the DHCP server on your router.  See the User Guide of your router for more details.

• Photosmart 7510 Automatic Document Feeder. It copies a weird size double-sided?

  I have a Photosmart 7510.  I've never used the automatic document feeder and could not find anywhere online how to use it.  I want to know if I can put in a 5 1/2 x 5 1/2 image from a funeral and did copy both sides so she's going to look like a card... all on one as the original.

  Specifications

  Hi grammafaith,

  To copy the size you want through the ADF is not supported. According to the specifications, the larger size of the photo tray is 5 x 7, and use the main charger would cause a paper jam.

  I've included here for 'copy a MultiPage Original' document. I tried as follows on the 7510 I and was able to copy successfully on both sides.

  I've also included the steps here for you.
  (1) place the point on the scanner glass
  2) press the button copy
  3) press the Settings button at the bottom left
  (4) make sure that only 2 sides copy is turned on
  5) Press Start
  (6) follow the instructions on the screen to load the second page / or return the paper and continue

  Please let me know if this has worked successfully for you, thank you.

• Photosmart c7280 will not keep Wi - Fi. said the radio but the radio works failed. repairable

  HP photosmart c7280 wireless printer has been working and connected to the router. Stop printing. The test report under collar "Radio on", according to Radio wireless working' fail. Is - fixable? The printer is only used wireless and not as part of a networked system.

  I thank very you much for your help and confirmation. I certainly could have been more specific about the problem and what I did. It was my first time, and you were very understanding.

  Thank you once again

  Sandy

• Base of screen is stuck in the down position

  I posted this earlier today and for some reason any, that it has been deleted. (I know it's there an hour after I posted it, so I'm not sure why it was deleted).  Anyway. I have a screen Dell UltraSharp 2405FPW monitor and today by chance, I pushed the monitor down and clicking on it in the locked position.  Until today, I wasn't even aware that he had that.  Long story short I fell on the dell site and discovered that you have to press the Unlock button.  Unfortunately, this does not work on my stand.  The button pushes into a fine, but the base of the monitor will not spark.  I use the two landscapes and modes Portrait every day and really need the stand to get back to the top, so I can rotate.  With all this down, it is almost impossible to rotate and when you do you must rear angle as far as it goes which makes it useless.  I went on Dell Chat and was essentially told too bad and I need to find someone to fix it for me or buy a new monitor.  Then he me the unplugged.  Note I was not angry or abusive up to this point, I was just trying to get it fixed.  Needless to say, after he abruptly ended the session, I was less happy that I almost lost my morning trying to solve this problem (only 30 minutes maximum was with the guys from cat). Anyway. The system is a XPS 600 and is still under warranty for another year.  I really want to spend another $600 on a new monitor just because the support is stuck, but I really need to be able to go back and fourth between portrait and landscape.  Does anyone know any way for me to fix this or get Dell to help me solve this problem? Any suggestion would be appreciated.

  Jason

  When you encounter any gluing or jam session with the base of the screen, perform them following operations =

  While pushing the button locking/release on the rear side of the stand, press down on the top of the screen to the ground, then gently pull the screen up.

• Photosmart 7520 series: error Photosmart 7520 series Document feeder

  Error message when you try to print, copy, fax, bed or document scan power - it says that I have to re - load the document into the charger and I am not fed any document.

  Hi @FaithHopeLove,

  Welcome to the Forums of HP Support!

  I see that your HP Photosmart 7520 printer will not print because of this error message "re - load the document". I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand the frustration you are experiencing. It seems that the printer is stuck in an error state or there is a blockage in the ADF (ADF).

  I would like to do a hard reset to see if that will solve the problem. Let the printer and disconnect the printer cable and the wall socket for 60 seconds. Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.

  Make sure that the printer is connected directly to a wall outlet (do not use a bar or a surge protector). This ensures that the printer is full on and can help this situation.

  If you have access to another computer running Windows 8 or an earlier version, please update the firmware of the printer. Click here to go to the download page.

  To make sure that there are no obstructions in the ADF, follow this guide:

  The ADF (ADF) is not get paper

  If the problem persists, I suggest we try semi Full Reset. I can send you this information in a private message. In the forum next to your handle name simply click on the envelope to see.

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.

  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair. Cost of repair out-of-warranty printers may apply. What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:

  Step 1. Open the link: www.hp.com/contacthp/

  Step 2. Enter the product number or select Auto detection

  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.

  Step 4. Scroll down and click on options contact HP - click Get phone number if number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck! Happy smiley

• Flag 23: problem of scanning hp photosmart 7520: Automatic Document feeding

  My photosmart hp 7520 worked well since I got a couple of months.  I have often used the feature of the parser for a single page (or photo) both placed on the glass.  I also used it to scan several pages in a file PDF - one page at a time placed on the glass (not via the ADF because they are double sided pages).  Two days ago, I started having trouble with the scan function.  When I select Scan--> computer-->-->--> PDF Document MYPC and load a single page on glass, sometimes it allows me to analyze this page, I request to load the next page which I do but that's all.  He said that the analysis has been a success and the document is saved even if I have additional pages.  It doesn't gives me the opportunity to make more than two pages.  At other times, as soon as I put the first page on the glass and go to the scanner, it does "No preview available when you use the ADF" even if there is no paper in the ADF.  I did not any changes for the 7520 or Pavilion.  Is it a software HP 7520 glitch or hardware problem?  I tried the normal stuff of uninstalling the software and put it back, by restarting and unplugging the 7520, etc. all to nothing does not.  Same problems keep occurred.  Suggestions?  Thank you.

  Hi davedunbar,

  Thanks for your efforts in solving problems, and Yes, I'd say gives us a call to see about a replacement printer. We tried all the troubleshooting steps at this stage.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope you enjoy your Monday

• HP Photosmart C7280 - cannot get top of breaks on the screen

  Hello.

  I try to enter a new encryption key for the wireless network configuration. All alphabetic characters in the key must be top of the case.

  I have the arrow down to abc and press OK so it turns into ABC. However, when I have the arrow back up to type out a letter, lowercase.

  Can you please tell me how to type uppercase? It seems that if I do everything right, but it does not.

  Thank you!

  Hi there njcmiller, welcome to the forums if you are to press one of the numbers/letters on the keyboard several times, the letter should change lowercase uppercase, as would a cell phone to send SMS. I hope this works, cordially,

• wagon stuck in the original position

  I have a HP Photosmart C6380 all-in-One Printer, the cart is stuck in position under the metal cover.  Error message 'clear transport jam '.  The instructions to clear it on this site did not work.  Any suggestions?

  Have you checked to make sure nothing is caught in the rollers at the back of the printer?  Also, check inside the printer as best as you can with a flashlight to see if the small pieces of paper can be jamming to the transport.

  Thus, there is a document with the steps to resolve a deadlock of transportation provided by HP.  The document can be found here.  Follow the steps in the document to troubleshoot and try to clear the jam error message.

  I hope this helps.

• CDROM is stuck in the closed position, how do I open it manually?

  door cd/dvd rom

  is stuck w/switch on that Panel fell I put on, the door does not open

  Hello

  1. you are using a laptop or a desktop computer?

  2. What is the number of brand and model of the laptop or desktop?

  3. what operating system is installed on the computer?

  If you use Windows Vista or Windows 7, you can try the steps mentioned below and check if they help to resolve the issue.

  (a) restart the computer.

  (b) if the keyboard is equipped with a CD/DVD eject button, press it. The Eject key is usually placed by the volume knob and is marked by a triangle pointing upward with a line underneath.

  (c) in Windows 7 or Windows Vista, click Start, and then click computer.

  (d) right click on the drive icon of CD-ROM or DVD that is stuck and then click on eject

  (e) if the CD or DVD drive door button is a bar long clear plastic on the front of the computer, press firmly on the right side of the bar. Some models have a button on the front panel of the computer to the right of the door to hinge. Press the button to eject the disc.

  (f) if the drive door is covering the door of the real and made part of the case of the computer, open the door which is part of the computer case and press the eject button on the front of the player.

  (g) restart the computer and press the button to eject at the front of the car when the first screen appears (before Windows starts). If the door opens this way, but does not open in Windows, other software takes control of the driver CD. Try to stop or configuration of any software programs that create records or control the CD or DVD drive

  If the steps above do not help, you can contact the hardware manufacturer for assistance.

• Error, said documents, does not not at the opening of libraries or documents of libraries

  Title: original files

  When I raise libraries, documwnts, I get a box saying "not work documents.libraries

  Hello

  Please, try the fix described in this article and see if that helps:
  http://www.kapilarya.com/fix-library-MS-is-no-longer-working-in-Windows-7-8
  Hope this helps, good luck :)

• my browser is stuck on the opening page.

  Seems not to matter to this site, I tried to reach, or what site I put it as my homepage. I get no response. The problem seems related to the intelligence program Scorpio who touched my computer. Is there a way to remove that?

  It is on Windows, I guess.

  First, you must uninstall all suspicious software through the control panel of Windows configuration, either add or remove programs (XP) or uninstall a program. You can click on the installation date column to sort by date and see which have been grouped.

  Then, run some malware supplemental sweeps using the tools listed in this article to support: Troubleshooting Firefox problems caused by malware. If you can not download them using IE, you can be able to run Firefox in Safe Mode.

  Firefox Safe mode is a standard diagnostic tool in order to avoid interference by extensions (and some custom settings). More info: questions to troubleshoot Firefox in Safe Mode.

  You can restart Firefox in Mode safe help

  Help > restart with disabled modules

  If you cannot use the menus in Firefox in normal mode, close all Firefox Windows, then hold down the SHIFT key when you start Firefox.

  In the small dialog box that appears, click on 'Start mode safe' (not Reset)

  Third, delete them or disable all non-essential or unrecognized extensions on page modules. Either:

  • CTRL + SHIFT + a
  • Firefox orange (or the Tools menu) button > Add ons

  In the left column, click Extensions. Then, in case of doubt, disable or remove.

  Typically, a link will appear above at least an extension disabled to restart Firefox. You can complete your work on the tab and click one of the links in the last step.

  From the latest discussions on Websteroids / ScorpionSaver / drive Tube, you may have some malware which relocate or reactivate the unwanted extensions, in this hidden folder:

  C:\ProgramData\Updater

  If Windows won't let you delete a .exe file in this folder, you will need to kill the corresponding process in Windows Task Manager. In some cases, it is easier to restart Windows using Windows safe, then run the malware cleaning programs.

• TouchSmart 520: The computer is stuck on the opening of the screens.

  Hi all

  It will be a little long because I try to give as much detail as possible. I have a desktop HP Touchsmart 520. The other day, I want to run an OS based on Linux from a USB key. I did once before, so I did what I did the last time. I unplugged, take off the back, then removed the hard drive, then plugged the USB key. I was hoping that since I didn't drive hard in, the computer would then operate the stick because of the boot order. He did bring up the screen of the OS, but gave me an error on failure. I turned it off and then return and go to the bios to change the configuration. I found the USB from the menu, but couldn't move, so I tried to disable the first option for the hard drive. I plugged the USB back in, but it does not still work, so I tried to drive hard back. Something happened somewhere in all this, the computer froze, so I tried to hit different buttons to see if I could get an answer, but nothing, so I cut. When I cut back on, I can't no longer to enter the BIOS. The usual HP screen comes up and says press ESC to enter on the start menu, and if I hit him in the first second coming he will take me to a black screen that has my computer on this subject record, starting with the processor type, processor speed, etc. (if I hit any button in a moment the computer hangs on the HP screen). This black screen is as far as I can go and the computer always crashes here, no matter what button I push, but it is said in the lower right corner of the activity for any button I pressed on, for example if I press F2 on the HP screen, it will go to the black screen with my characteristics and in the lower right It will read Diagnostics; If I am pressing F10, it will do as above but read the configuration. He never goes beyond this screen. I know that's not my hard drive, because he wasn't in when it started happening, nor is it possible that a virus has been on the USB port, as it's a BONE checked and I do not use this stick for something else. I know that something happened when I was in the BIOS, but I don't know how to fix it. Nobody knows what is happening or what I can do to try to fix it? It would be very appreciated that I can't afford to take it in, and I don't think it's a bad thing in the first place, I don't know what I'm doing. Thanks to you all!

  Hello

  seems that there is a corruption of the bios. First try to make BIOS clear CMOS. He must go, unplug the power supply, open it on the back and to remove the RTC (real time clock) battery for a couple miutes and then turn the unit and go to the bios and load bios defaults. As a guide to go and use the services for your product guide. You specify exactly which model you have (model number or product number), but look on hp.com for service guide: http://h10032.www1.hp.com/ctg/Manual/c03357415 for more details.

  Note that this operation to be experienced user but you wrote that you have disconnected the HARD drive, you have already opened the unit if you wait is at the level to do so.

  If the RTC cmos clear won't help, report back and we will help you make bios flash BACK.