IdeaPad 13: Touch not working not not after connecting USB device

Similar Questions

• Laptop does not not after connected

  My laptop does not respond after that I logged. It shows all icons, the cursor moves, but when I click on any icon it does not at all. And when to stop I have to press the power button / stop. Help, please. Thank you.

  Hi RAS.

  Thanks for posting the query on Microsoft Community.

  It could be due to drivers or system files corrupted or damaged. Don't worry, will help you with the question.

  You can try the steps in the link below and check if it helps.

  8.1 Windows, Windows 8 or Windows 7 hangs or freezes: (at the start, recent hardware or software changes, system files damaged due to hardware problems, due to malware or Antivirus software)

  https://support.Microsoft.com/en-us/KB/2681286

  Warning of Chkdsk.

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Anti Virus WARNING: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  To run the above steps if you are unable to use the system, then I suggest you to place the computer in Safe Mode and the clean boot and check if you can try these steps.

  Operate the system using the safe and check. It starts with a minimal set of drivers and services.

  Start your computer in Mode safe:
  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  If the problem is not in safe mode then try to clean boot.

  Try the system to the boot. This will eliminate the conflicts of software that occur when you install a program or an update or when you run a program in Windows. It starts Windows by using a minimal set of drivers and startup programs.
  How to perform a clean boot in Windows: http://support.microsoft.com/kb/929135

  Note: After troubleshooting, consult this "How to reset the computer to start normally after a boot minimum troubleshooting" section in the link above.

  I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.

• Not recognized/defective USB device

  My sister has her ipod touch over at me because she asked me to restore it for her because she has forgotten her password. I tried to plug the ipod into my laptop and a message pops up saying, "USB device not recognized. One of the USB devices attached to this computer has malfunctioned and windows does not recognize it. "I sat during most of the night trying to figure out what's wrong. I've been to about 50 Web sites and that you have not yet found a solution. The Ipod does not charge when connected to my laptop, but it will be when its connected to my PS3. I have all the updated drivers, update to itunes, etc. Its driving me crazy. All solutions?

  Hello

  What it does not appear in Device Manager?

  It could be that the drivers for this port USB is not updated.

  Method 1:

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/en-us?WA=wsignin1.0

  Method 2:

  Follow the steps mentioned below:

  a. click on start and then use the search box.

  b. type devmgmt.msc, and then click OK. Device Manager opens.

  c. expand Bus USB controllers.

  Note that you have to scroll down to find this point.

  d. right-click on the first USB controller under Bus USB controllers and then click on uninstall to remove it.

  e. Repeat step 4 for each USB controller is listed under Bus USB controllers.

  f. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  g. check the USB device to see if it works.

  These methods are worth a try. Answer please if you need assistance.

• ProBook 4740 s will not feed if USB devices are connected

  G ' Day, I have a ProBook s 4740 and after taking the laptop to the site, when I'm home and plugged things back, by pressing the power button would see it for a few seconds and then od light out. The LED above the power would have flashes once and then turns off. Needless to say, it would not start up.

  After a lot of frustration, I found that by unplugging all (wired Ethernet and USB devices) and by pressing the power button it would start up and even when starting I could plug the devices and everything is OK.

  I had to return to the site today and when I came back again, it wouldn't power up until I unplugged the USB devices. USB devices are external hard drives only, all running through a powered USB hub.

  This configuration has worked without any problems for wells in the year I've had the ProBook.

  This could be the cause?

  Thank you.

  The last update :-)

  After downloading the BIOS update, I decided to wait until I had a break in things until I applied it. Then around one hour before, I saw the red exclamation mark on the HP Support Assistant in the taskbar. Open it, there was an update of the available BIOS, so I decided to let him do. At this point, no indication that it was the F.60 update.

  I hate doing these updates that work at the machine code level where if things go wrong, they can go horribly wrong.

  Well, everything went well. Updated the BIOS and restart the computer. I went back in to the support assistant and got the information on the computer, and he says that it is now the F.60 version. If she went from F.43 to F.60

  I power it off, wait a minute, then restarted with everything plugged in and it worked correctly.

  Thanks again for your help.

• Computer doesn't recognize is not the Vista USB devices

  I have been looking for forums for hours. I put music on my mp3 and it worked fine, I switch between two different players. then I went to plug one of them in and... . nothing. USB ports are supported but computer, do not put the devices, I can't access it anywhere. Ditto for everything I plug into them. fee but usually has access to any device I plug im in. going to vegas tomorrow and would really like to put new music on my player. can anyone help please?

  * original title - USB problem *.

  Hello

  ·        You get an error message when you connect the USB device?

  Method 1:

  I suggest you follow the steps mentioned below and check if the problem is resolved.

  With the drive plugged in

  1. go to Control Panel by clicking the Start button and select Administrative Tools.

  2. click computer management , and then select disk management on the left

  3. then turn on the player.

  Method 2:

  I suggest to assign a new drive letter and check if the USB key questions in the computer.

  Change, add, or remove a drive letter

  http://Windows.Microsoft.com/en-us/Windows7/change-add-or-remove-a-drive-letter

  Method 3:

  Remove and reinstall all USB controllers. To remove and reinstall all USB controllers, follow these steps:

  1. click Startand click run type sysdm.cpl in the area of publication, and then click OK.

  2 click the hardware tab .

  3. click the Device Manager button.

  4. develop Bus USB controllers.

  5 right-click every device under the theUniversal Serial Bus controllers node and then click Uninstall to remove them one at a time.

  6. restart the computer and reinstall the USB controllers.

  7. connect the removable USB storage device and test to make sure that the problem is solved.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Push does not not after restarting the device?

  So we have successfully implemented BlackBerry push with our Android app-focus.  The application registers with RIM and receives a response of success.  We register successfully the info back to our application server.  Our application server send push messages to the device, they are accepted by the RIM servers and are received successfully on the device.  Everything is great!

  Except...

  If we shut down the device or reboot the device when he returns is no longer receives pushes for the application unless that register again with RIM BPA.  They are sent to the device and the same agreed before they get simply never received on the device.

  What we're doing wrong?  Is he expected to receive pushed back them after a reboot of the device that the user must launch our app to record with pusher?  It would be really weird because a user will not necessarily start the application after each reboot.

  Thanks for that bring to our attention. We have the Android Runtime search dev team in this.

  As ennova2005 said, you need to unregistor/re-resistance after a reboot as a work-around. In addition, because the application does not start automatically, the application must be opened/started by the user.

  Thank you

• Satellite L450D not start - think usb device is connected

  Hello. I have a portable satellite L450D running Windows 7, which will not start. It gets to the loading of the windows with the windows logo page, but it will not go beyond this point.

  I tried repairing the system, and that tells me that a device is always connected to the laptop. I think it's maybe my phone, I had connected by usb last week. The usb cable is removed physically but the laptop obviously thinks that it is still connected.

  I'm passed through different service options - system repair, System Restore, restore the last good config, boot into safe mode but nothing seems to work.

  Ive tried to connect the phone while the laptop is trying to start and then disconnect it but still no luck. The laptop still think that the phone is connected.

  Ive not tridd remove the battery from the laptop, as it's apparently quite difficult.

  Any ideas anyone? Thanks in advance

  Hello

  I would recommend you check the boot order in the BIOS.
  Go to the BIOS by pressing F2 by turning on the device.
  Now, press F9 to get the default settings and save the changes press F10.
  Also check if you can disable the legacy USB if it s is not available, ignore this tip.
  Now, restart the laptop and test if it would boot from the HARD drive.

• Not resettable 6210 USB device

  Hello

  I am having some problems with a USB-6210, when I connect it to the target computer.  The following is installed:

  - NI DAQmx 8.9.5

  - NO MAX 4.6.0

  I can run one or two tasks, until I get the following error:

  ERROR-88708 occurred to the DAQ Assistant

  When I try to reset the device, I get the following error:

  ERROR-50405. A parameter of type pointer is not valid.

  Then I need to unplug the USB and reconnect to operate again.

  I plugged the USB-6210 to my laptop (which has different software versions installed), I don't have this problem.  Makes me think that the camera is ok.  Are there known with these versions of software and the USB-6210 bugs?

  See you soon

  Hi Glenn,.

  Thanks for the reply.  I called support AND shortly after the announcement yesterday, and they suggested that it could be related to noise on the USB cable or a USB hub.  I tried another USB cable (the original cable was wired near other equipment potentially noisy), and another USB port (went to the back, rather than on the front), and the problem has not reappeared since.

• Satellite A200 not power external USB devices in mode 'sleep'

  I have a new A200. I have and USB hub and disc external hard USB powered. When I put it in mode 'sleep' their lights stays on. It came with Vista. I searched for the setting, but I could not find. It is not good for the battery. Any advise?

  Thank you.

  -Sinan

  Hello

  The lights are also on when the laptop is to stay in sleep mode or hibernation mode.
  You cannot disable the led s

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?

• Can not find the USB device on computer

  I have a cell phone Samsung A680 I try to take pictures off. I connected the USB cord to the computer and it found and installed the drivers that I needed, but when I opened my computer, it doesn't appear there or on the lower right corner of the taskbar. Does anyone know how to find so I can remove the photos?
  I have a Dell Inspiron with Windows Vista. In addition, it recognizes that it is there because it makes the sound when I plug in the USB and get him out.

  Thank you

  Hello weinkermeyer,

  Thank you for visiting the Microsoft answers community.

  I have studied your phone, and Samsung, phone (A680) has no available connectivity options.
  http://www.Samsung.com/us/consumer/mobile/mobile-phones/Sprint-phones/SPH-A680SSSXAR/index.idx?PAGETYPE=prd_detail&tab=spec

  What I would try, if you want to keep the pictures is picturemail just send to your e-mail address. Of course, depending on your phone plan, you will have to pay a fee in order to send the picturemail. If for some reason you cannot send picturemail to an email address, simply send to a friend or a family member who has a phone capable of connecting and downloading the pictures.

  Hope this helps Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error on blue screen after connecting USB blackBerry Smartphones

  Hello, I have a new 8100. Everything is great, everything works, but the problem appeared after I installed the software and I have connected the mobile to the computer by USB... the blue screen error Windows Vista appeared, then
  After the automatic reboot of my computer
  He says the following errors:

  "Problemas con Firma:
  Number del problema evento: BlueScreen (name of the)
  Led operating system version: 6.0.6000.2.0.0.768.3 (OS version)
  ID of regional config: 3082 (locale ID)

  Information adicional del problema: (other info on the problem)
  BCCode: 4th
  BCP1: 0000009A
  BCP2: 0003EA16
  BCP3: 00000006
  BCP4: 00000002
  OS version: 6_0_6000
  Service Pack: 0_0
  Product: 768_1

  Archivos than IR a State el problema: (files that help describe the problem)
  C:\Windows\Minidump\Mini010609-03.dmp
  C:\Users\antonio\AppData\Local\Temp\WER-110323-0.SysData.XML
  C:\Users\antonio\AppData\Local\Temp\WER6C68.tmp.version.txt

  LEA nuestra declaracion of privacy:
    http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0C0A
  "

  I didn't have anything wrong with my Vista OS before

  Thanks in advance

  Hi and welcome to the forums!

  I read very well Spanish, but did you leave the connected Blackberry when you

  restarted the PC? Vista may have tried to use the BB as a drive for system functions or error checking.

  Thank you

  Bifocals

• Satellite L300-01:00 - Dynadock question after Connect USB cable

  Hello!

  I am new to this forum and I am the proud owner of a Toshiba Satellite L300-01:00 I received with a Toshiba Dynadock as a gift.

  The problem I have is with my PPPoE Internet connection. If I have the Internet cable in the Dynadock and then plug the USB cable into the laptop, I can connect to Internet but after that we will say 10-15 minutes there is a break in the connection and downloads, instant messaging services and other services stops for a moment.

  For example if I download a file or play a game that I am disconnected and it is very unpleasant. I don't have this kind of problem, when I plug the Internet cable directly into the laptop.

  If anyone can help please let me know. Thanks in advance.

  Hello!

  You did to be sure you have the latest drivers?
  I would also like to do a BIOS update.

  Take a look at the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  I think it could also be a problem with your internet provider.
  You can test it with another computer or laptop.

  Good bye

• USB Device not recognized Hp OfficeJet 6600

  Hello all - I use my desktop Hp 6600 (connected via usb) jet and my computer (dell E6430 latitude) says that it is a usb device not recognized.  I tried a lot of troubleshooting, including the removal of usb controllers and reinstall, but which doesn't seem to work.  I'd like to help as soon as POSSIBLE. Again, I must keep my printer cable, because the network, I refuse the acess printers or something like that.

  Thank you

  J

  Hello

  If I understand correctly your computer does not detect the printer. You can try the following steps and check the results.

  1) inspect the cable USB and connection:- icon on the USB () facing up when the cable is connected to the product correctly. Check the back of your product and the back of your computer to make sure that the USB cable connects correctly and safely. After that you make sure that the USB cable connects correctly and safely, consider the following guidelines to check other potential problems associated with USB: Connect any other USB device. Connect any other USB device to the computer and check if it is detected. USB ports on the keyboard. USB ports on the keyboard and on the front of some computers is maybe not powerful enough to support the product. If the USB cable connects to the USB port on the keyboard, try to connect to it in another USB port on the computer. Length of the cable USB. HP recommends that the lower USB cables or equal to 5 m (16 ft 5 in) long. However, a USB cable which is 5 m (16 ft 5 in) in length must be of high quality. Otherwise, HP recommends using a USB cable that is less than 2 m (3 ft 3 in). Do not use connection cables to increase the length of the cable. Use a powered USB hub, if you need more length. USB ports replacing. Connect the USB cable to a different port on the computer to make sure that the USB port on the computer is not the cause of the problem. Defective USB cable. Replace the USB cable to ensure that the existing cable is not defective. Conflicting USB ports. Disconnect all other USB, USB, USB cameras scanners printers and all other connected USB devices. Start the connection of these devices one at a time to determine if the devices to use too much power. Plan to buy and install a hub USB powered if necessary. (2) power Off and power of the device. (3) update the Windows Device Manager: (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens. (b) in the Open text box, type devmgmt.msc and press ENTER. The Windows Device Manager opens. (c) lists to look for your HP printer in Bus USB controllers or other devices . (d) right click on the entry for device to device/unknown HP and then click on set to update driver. The material up to date hospitality Assistant opens. (e) select install the software automatically and click Next. Follow the on-screen instructions to complete the refresh Device Manager. (f) repeat these s for all entries of device with a yellow exclamation point. (4) delete the temporary files and folders. (5) disable some startup items: -. (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens. (b) in the Open box, type msconfig, and click OK. The System Configuration Utility window opens. (a) click on the general tab, click Selective startup. (b) if there is a check next to load startup items, select the check box to remove it. (c) click on the Services tab and then click on the hide all Microsoft Services check box.

  (d) click Disable all.

  (e) click on apply and then click Close.

  (f) restart the computer.

  (6) make sure that the Plug-and-Play Service is activated: -.

  (a) click Start (for Windows XP) or the Windows Logo (for Windows Vista and 7), and then click run. The run window opens.

  (b) in the Open box, type services.msc, and then click OK. The Services window opens.

  (c) to seek the 'Plug-and-Play services' and check if the status is started.

  (d) if the status is not started, then right-click on it and select start.

  (e) once on the way out of the window.

  (7) uninstall and reinstall the printer software.

  (8) re-enable the startup programs: -.

  (a) click Startand then click run. The run window opens.

  (b) in the Open box, type msconfig, and click OK. The System Configuration utility window opens.

  (c) click the general tab, click Normal startup.

  (d) click the Services tab, and then select the hide all Microsoft Services check box.

  (e) click applyand then click close.

  (f) click on reboot to apply the changes to the next time the computer starts.

  (9) try to install the software on another computer.

  Although I am an employee of HP, I speak for myself and not for HP.

  -Say 'Thank you' by clicking on the star of congratulations in the post helped you.
  -Please indicate the position that solved your problem as "accepted Solution".

• Device USB error: USB device not recognized

  For a week to 10 days I could not connect my USB drive to the USB port. Also my keyboard and mouse stopped working because I was using a USB hub. It must have been a few Windows Vista update recently which caused this problem with USB devices. It does not recognize the USB devices. I can use the USB device on my laptop mini where I have Windows 7.

  Microsoft is going to solve the problem in Windows Vista. There should be no reason that we cannot use USB devices and before 10 days ago, it was not a problem.

  Thank you for your help.

  Hi NRuss,

  1. have you checked if the devices are getting detected in Device Manager?

  Step 1: Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Step 2: Uninstall all USB device manager entries

  a. Click Start and typedevmgmt.msc and then click OK. Device Manager opens.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat step 4 for each USB controller is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  f. check the USB device to see if it works

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.