installation of unknown device causing vista freeze

Similar Questions

• Satellite A660-10W - after Windows 7 installation of unknown devices

  So I have the Satellite A660-10W, and I reinstalled Windows 7 it came with Windows 7 ultimate 64-bit. First thing, it's when I use fn + F6/F7 (other combinations work) to the brightness levels, it does not work, brightness does not change. And the other thing is that there seems to be some unknown devices.

  This is all hope someone can think of what could it be, thanks in advance. :)
  Link: [http://store.picbg.net/pubpic/B4/3E/3ca598fbde5fb43e.png]

  You should try to install: Bluetooth, infrared, Modem drivers...

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

  In any case, it will be better if you post the id of the device / vendor:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=78

• Storage device causes vista to freeze

  I have an emachine with two different usb ports e620.
  I plug a storage of 8 GB sandisk into one, a TI freeze completely the computer. The computer is up to date as I know, the automatic updates are enabled.

  Hi Twss22,

  You can try to use your boot USB storage device and check if that helps. A clean boot helps eliminate software conflicts.
  The following link has steps showing how to perform the clean boot. http://support.Microsoft.com/kb/929135  
  (1) perform the clean boot
  i. Click Start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  II. in the general tab, click Selective startup.
  III. under Selective startup, clear the check box load startup items.
  IV. click the Services tab, select the hide all Microsoft Services check box and then click Disable all.
  v. click OK.
  VI. When you are prompted, click on restart.
  VII. after the computer starts, check if the problem is resolved.

  (2) enable half the services
  (3) determine whether the problem returns
  (4) enable half of the startup items
  (5) determine if the problem returns
  (6) repeat the steps above until you find out which program or service is causing the issue
   
  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.
   
  Note: Please make sure that the computer is configured to start as usual by following step 7 of article http://support.microsoft.com/kb/929135 .
  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  (i) click Start, type msconfig.exe in the start search box and press ENTER. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  (II) on the general tab, click the Normal startup option, and then click OK.

  Diana
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Satellite Pro A100 (PSAAC) - freezing for a second unknown device

  Hello

  I have recently reinstalled Windows on my computer, after installation, is a problem. With an interval of 10-15, my computer hangs at about a second - the computer reacts to the entry, and if a sound is played he repeats again and again.

  I don't know if it has something to do with it, but when I start the computer I get the error message "cannot read the Manager!" I noticed that I have a unknown device in my device manager, location: location 65535 (internal Bus High Definition Audio). I can't find the driver.

  I don't know if the problems are related, I just want the freezing part to fix.

  Best wishes
  Hans

  Hello

  you have installed a sound card driver? Anyway, how to identify the unknown device, read here:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=58

• 'Unknown devices' after downgrad from Vista to Windows XP on Portege R500?

  I recently downgraded my Portege R500 of Vista installed at the factory for WinXP.
  I managed to install without problem, and today I met an "unknown device" which I can't fix.

  The details of this device:
  Location: on Interl 82801GBM (ICH7-M) LPC Interface Controller - 27 b 9
  Device Instance ID of: ACPI\IFX0102\4 & 38462492 & 0
  Hardware ID: ACPI\IFX0102 * IFX0102
  Compatible ID: * PNP0C31

  If anyone can help, please help!

  Hello

  Have you installed the XP drivers all available from the European pilot of Toshiba page?
  Please take the look in installation instructions txt file. You will find a list of all the necessary drivers that must be installed. The order of installation is important.
  Please install all drivers as mentioned in the installation instructions.

  PS: On the page there is also an application of Infineon Trusted Platform Module.

  Greetings

• Satellite A100-237: unknown device after installing Vista

  Hi all

  Just installed vista on my A100-237... After doing the upgrade of the BIOS and the installation of the "unknown device" Value Pack, with the location "on system compatible ACPI Microsoft" appeared in my device manager, any ideas on how to address this issue?

  Thanks in advance!

  Hello

  Could you please check if you can see the 'Batteries' entry under ' computer in Device Manager?
  As far as I know that the entrance of batteries should have a "Microsoft SMART Battery" & "Microsoft SMART Battery subsystem.

  If there is an unknown device, this might have something to do with Microsoft ACPI Compliant Embedded Controller.
  In this case it seems that you need a driver for MS SMART SMART Battery & MS battery subsystem.

  pleasae also check this thread;
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=14575

• Vista - usb ports are not recognized unknown device

  Vista - usb ports are not recognized unknown device. any usb device it appears unknown. all worked a few days hardly, but after that I connected my Kodak camera - which does not, now, nothing works. Any help would be appreciated.

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  Follow the instructions below that may help you resolve the issue.

  Method 1:

  Try to connect USB devices to a different USB port and check if you are able to access.

  Method 2:

  Click on the link below to run Fix it which will help you to solve the problem.

  Tips for solving problems of USB devices

  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx

  Click on the link below and install the update.

  Rollup cumulative update for USB in Windows Vista Basic components

  http://support.Microsoft.com/kb/941600

  Try to connect the camcorder to the other USB port and on the other computer and see if the problem is resolved.

  Method 3:

  Let us try to disable the Antivirus security software and check the number.

  Re-enable the security software after checking the issue.

  You can also try disabling the firewall and check the issue.

  Re-enable the firewall after checking the issue.

  Method 4:

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure.

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot

  Step 2: Enable half the services

  Step 3: Determine whether the problem returns

  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns

  Step 6: Resolve the problem

  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista

  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to the Normal mode.

  Uninstall or update the program that is causing the problem.

  Check whether the problem is resolved.

  You can also check out the link below.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/6be4581d-8fbd-407F-815E-b475c35ca586

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• iPod touch installs as an unknown device, gives 43 error code

  ORIGINAL TITLE: Hi, need help!

  I have an ipod touch and recently my computer windows vista installs it as an unknown device. Then, the computer gives me code error 43 and USB\VID_0000 & PID_0000\5 & 2010C5D6 & 1 & 3 How to fix? He also says that my camera is faulty so how can I found out if its my ipod which is really broken because it works fine for me. I searched but nothing seems to answer my questions directly. Help, please!

  Hello

  Check with iPod Support and Forums for more information if necessary.

  -IPod support
  http://www.Apple.com/support/iPod/

  iTunes and iPod Support
  http://www.Apple.com/support/

  Each iPod - iPod help & Technical Support (part 3)
  http://www.EveryiPod.com/iPod-help/index.html

  ---------------------------------------------------------------------

  For most MP3 players that can and will be able to be synced to WMP - iPod syncs not natively for Windows 7.

  Set the MP3 MTP Mode for WMP sync - mode MSC to treat the MP3 as a reader.
  (Now its set to MSC)<-- this="" is="" for="" mp3="" in="" general="" and="" ipod="" will="" not="" usually="">

  Your MP3 player should have 2 settings - MSC which should allow the player to be used as an external drive
  and PSG that is the parameter to use to sync with WMP. Remove the MP3 and restart the computer.
  Change the MP3 in MTP mode - it power off and plug it in.

  ======================================

  There is a plugin to let WMP sync music to an iPod:
  http://thewelltemperedcomputer.com/SW/WMP/sync.htm.------

  WinAmp supports iPod
  http://www.Winamp.com/

  How to use Winamp to manage your iPod
  http://www.SimpleHelp.NET/2007/07/07/how-to-use-Winamp-to-manage-your-iPod/

  WinAmp - Forums
  http://forums.Winamp.com/

  6 ways to synchronize your iPod to computer without iTunes
  http://www.MakeUseOf.com/tag/6-ways-sync-iPod-computer-iTunes/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Portege M440 - Vista problems: problems of Bluetooth, the unknown device and tablet.

  I just installed Vista on my Portege M400 and installed all the drivers on the driver Vista page.
  But I have several questions...

  1: bluetooth does not work. I can't find anywhere in Control Panel whatever it is on a connection bluetooth or something else.

  2: after you have installed all the drivers on the driver Vista page, there is 2 "unknown device" in Device Manager. I can't find any information on what are these devices. However, when I tried to manually install the driver bluetooth on the first of them "Unknown device" he admitted the driver. This does not work on the other. And it does not solve the problem of the bluetooth missing.

  3: the tablet itself feature works very well - the pen and everything. But when I turn the screen into tablet mode it does not change the screen layout. Or the buttons on the lower part of the screen to work.

  I hope that there is some sort of solution to these problems - and that someone can help me.

  Concerning
  Jonas Hermansen

  I am also very interested in these drivers because all I know Toshiba Vista drivers are not available at this time.

• Satellite X 200 - 21 d - two unknown devices after installing Vista 64 bit

  I just newly installed (my Vista 64-bit), my laptop 21(d) and noticed that in Device Manager, there is option - hidden features, then 2 new unknown devices appear.
  What are these devices and where to find the right driver for it?

  Hi there is green Orchid,

  Is the vista 64-bit, that you have installed the software that came with the system or a version of windows?

  Before installing vista, have you checked if there are external devices connected to the system?

  Post edited by: iSkO

• Vista Ultimate on Equium A100 - 2 x "unknown devices".

  Equium A100-306 with XP Media Center Edition.
  So made as ready stickers clean install of Vista Ultimate (x 64).

  Now I have 2 "other devices" in the Panel.
  Has no 3, as mass storage controller was there too!

  There is a x 64 version of xx21 TI which does not, available from Download Center.
  Anyone know how I can track/identify devices & and/or drivers missing?
  DriverMax used and online update driver but nothing shows.

  MORE - everyone knows the A100-306 with proc duo T5500...
  Is this a 64-bit device real or is it a 32-bit system running a 64-bit processor?

  I have x 64 Vista loaded which should show 4 GB or more, but it reads still 3062 Mb.
  After reading a lot, I find that some people differentiate between the processor and system capacity, others are not.
  Is it possible to have a 64-bit processor in a 32-bit system?
  Why this issue has not been resolved?
  If it is a 32-bit system, why should we bother x 64 put OS on it?
  Confused on this so any help would be great.

  Yep! I have the latest version of the BIOS.
  Oddly enough, I had XP_MCE to show 4 GB of RAM, immediately after the BIOS update.

  Finally, thanks to everyone who asked (& responded to) other questions I had.
  I came, I tried, I got the answer...

  Everything above to sort & I'm a happy Bunny v..

  Please note that Toshiba Vista 64-bit drivers are not available on the Toshiba page and so some unknown devices may appear in the device because Manager the drivers not installed!

  > someone familiar with the A100-306 with proc duo T5500... Is this a 64-bit device real or is it a 32-bit system running a 64-bit processor
  Intel Core2 Duo T5500 Mobile is known as a Merom/64 Bit processor.

  > Is it possible to have a 64-bit processor in a 32-bit system?
  Yes, the processor supports 64-bit and 32 bit OS OS

  > If it is a 32-bit system, why should we mind x 64 put OS on it?
  You can install anything you want, but the question is whether you will get all the correct drivers

• Unknown device on the Satellite A200-SAE6E after the installation of Win XP

  I've got guys

  I got my new laptop from Vista to XP.

  But there is a problem:
  I can't find any drivers for the devices.
  A labeled being "unknown device".

  Y at - it a pack or a list to the place to get all the drivers.
  It becomes me crazy

  THX guys

  Hello

  It could be Robson (memory intel turbo). But unfortunately there are no drivers for Windows XP

• Portege R500 - 4 unknown devices after downgrade from Vista to XP

  Hi all

  I've downgraded a R500 from Vista to XP Pro SP2 and installed all drivers from the support page in the correct order, even in the device manager are always 4 unknown devices called 'data Interface '. Their hardware ID is:

  USB\VID_0930 & PID_1302 & MI_00\6 & 2EDD84F6 & 0 & 0000
  USB\VID_0930 & PID_1302 & MI_01\6 & 2EDD84F6 & 0 & 0001
  USB\VID_0930 & PID_1302 & MI_02\6 & 2EDD84F6 & 0 & 0002
  USB\VID_0930 & PID_1302 & MI_03\6 & 2EDD84F6 & 0 & 0003

  All 3 USB ports operate normally and at full speed, the Interface of data got to be something else.

  Thanks in advance for any advice or help

  Hello

  These are the modem and the features of com of your compilation in the 3G module.
  Unfortunately the drivers are not available on the European download page now.
  I guess it will take a few days until that pilots will be released.
  Please see http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp for this.

• Satellite U500-115 - unknown devices after the Installation of Win XP

  Hello

  I just installed Windows XP on a Satellite U500 - 115 (PSU5EE) and cannot get rid of several unknown devices in Device Manager.

  Before to install the operating system, I changed settings AHCI in the BIOS to Compatibility-Mode (IDE), so I don't need to inject the SATA driver during installation.

  These are the unknown devices:

  ACPI\PNP0C32\1 (location: Intel ICH9M LPC Interface Controller - 2919)

  ACPI\PNP0C32\2 (location: Intel ICH9M LPC Interface Controller - 2919)

  ACPI\PNP0C32\3 (location: Intel ICH9M LPC Interface Controller - 2919)

  ACPI\PNP0C32\4 (location: Intel ICH9M LPC Interface Controller - 2919)

  ACPI\TOS6205\2 & DABA3FF & 0 (location: System compatible ACPI Microsoft)

  Of course, I installed driver chipset and graphics driver from the toshiba download page, but the unknown devices are still there! Can you please tell me what kind of driver I need to install ACPI devices - and get rid of these unknown devices?

  Thanks in advance,
  Hans

  Hello

  In my opinion the unknown devices belongs to the SATA interface controller and these appear as unknown device because you have installed the XP compatible mode.

  Try to install the Intel Storage Manager driver.

  ACPI\TOS6205 device can be a Bluetooth device.
  You must install the battery Bluetooth to get rid of unknown device.

  welcome them

• Dv6700 Vista-&gt; Win7 - Intel(r) ICH8M LPC Interface Controller - 2815-Unknown Device

  Hey there, I couldn't find this one specifically for the dv6700. I had to reinstall everything, and this title was to improve the form of Vista to Windows 7.

  I tried to follow this guide:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and/Windows-7-upgrade-guide-for-dv6000-dv900...

  But I always came up with a problem in my device manager:

  Unknown device:

  Intel(r) ICH8M LPC Interface Controller - 2815

  Hardware ID

  ACPI\HPQ000

  * HPQ000

  I hope that this is sufficient to diagnose the problem. For another model, it seemed to be a thing of Bluetooth, but I don't think so here.

  Your help is very appreciated.

  Hello:

  Usually, it's the missing quick launch buttons driver:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-84862-1&cc=us&DLC=en&LC=en

  Paul