Joint connect to Cisco router

Similar Questions

• How can I connect a cisco router to the internet via a cable modem / router gateway

  I have searched here but can't find the exact answer that I'm looking. I have a switch and a router cisco 1760 2950. The router has an added ethernet wic card so I have two ethernet connections available. I would like to connect the cable modem gateway the router through one of the connections on the router, then the switch ethernet. I can't get this configuration to work. There are several different ways, I saw displayed to accomlish. DHCP, without dhcp, creating a separate network and giving the e0/0 cable an ip address in the range of addresses network gateways. None of this has worked. Can someone after the commands that must be entered on the router to make this possible?

  Hello, I'm assuming that your ISP is to give addresses via DHCP...

  And I suppose also we want to implement our router DHCP in our local network to give our PCs and laptops etc...

  So what we need to do is:

  conf t

  !

  interface e0/0

  Description # INTERNET #.

  IP access-group MY_WAN in

  DHCP IP address

  NAT outside IP

  No tap

  !

  interface e0/1

  # MY LAN description #.

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  !

  IP access-list standard MY_LAN

  permit 192.168.1.0 0.0.0.255

  !

  MY_WAN extended IP access list

  allow tcp any a Workbench

  refuse TCP a whole

  allow an ip

  !

  IP nat inside source list MY_LAN interface e0/0 overload

  !

  IP dhcp excluded-address 192.168.1.0 192.168.1.99

  !

  dhcp MY_LAN IP pool

  network 192.168.1.0 255.255.255.0

  default router 192.168.1.1

  Server DNS 8.8.4.4 8.8.8.8

  In this configuration, I applied an ACL for a protection to my router and my network to allow only established connections that Ive from my LAN to return to me. Anyone who tries to open a connection to your router will be refused. Everything is allowed. But you can change this option to be more specific rather than wide.

  On your switch, if you leave all ports in the vlan 1 and have as access ports, it should work.

  Hope this helps

  Please note the useful messages and don't forget to mark resolved all questions answers. Thank you.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Attempt to connect wi fi on my Dell computer, running windows XP? Have DSL but not Ethernet. Faced with problems. Checked with CISCO router but not help there. CANY anyone help

  I have a problem connecting to a Cisco E100 router to my computer. My count (office) does not have a wireless. I have DSL from. Cisco tells me to plug a router using Ethernet cable to connect. I don't have an Ethernet connection on my computer. At present I have USB connect the computer to the Westell modem.  Can anyone help? I hope this is enough information. Basically what I'm hoping to do is to install the WiFi so I can use a tablet now and maybe a laptop this last on.

  Thank you

  On the routers only house you can use USB connections are those provided by some ISPs.  An Ethernet connection between the router and the computer is far more preferred.

  Your router a Cisco E1000 or is it really E100 (I thought that Cisco makes a model with this designation not)?

  It is quite surprising that you don't have an Ethernet connection that is built into your computer.  What is the complete model number (or, preferably, the Number of Service Dell)?

  Open the Device Manager (start > run > devmgmt.msc > OK).  Expand the "Network card" category by clicking on the + next to him.  What devices are listed in this category.

  If you don't really have an Ethernet or an adapter wireless built into your computer, you can add one, using a PCI internal (if you have a desktop/Tower computer) or external (PC card for laptops) or USB to laptops or desktop/towers.

  Also, the normal configuration is to connect your DSL modem to the router and then the router to the computer.  If your Westell modem has an Ethernet connection, you must use your new router in a non-standard configuration.  Even if the Westell modem has an Ethernet port, you may need to do some reconfiguration for her as well.  What is the complete model of the Westell modem number?

• Cisco Connect connects to the router E2000

  I got an E2000 router, set up and works very well for years. Today, I tried to connect with Cisco Connect, I want to establish a network of separate comments (by the way, if there's a way to do this through the web management interface, please let me know!). However, the software is unable to connect to the router; the progress bar gets to 25%, and then eventually times out. I tried several computers on network, cable and wireless, with the same results. Any suggestions? Thank you!

  I solved the problem; I activated the setting "Allow users to set up" in the "Administration" tab, as well as utility access Web via HTTP. I don't know which of these settings did the trick, but I was able to connect and configure the network invited (even from a PC wireless).

• Cisco SG 300-20 switch connects to the router

  Hello

  I try to install my new switch Cisco SG300-20 in my local network, but I'm not succeed.

  The SG 300-20 fails to connect to my router.

  When the router is directly connected to the SG 300-20 I fails to obtain the DHCP configuration. Any port I try fails.

  When I add a former switch between the router and the SG 300-20, SG 300 - 20 manages to get the DHCP configuration.

  When I use a static IP on the SG 300-20 and the router is directly connected, it is not an operational bridge in the IPv4 configuration.

  Where I'm looking for a solution?

  The SG 300-20 is maybe defective and I would stay there?

  A. van Egmond

  A few things you can check are:

  See if the system is blinking. If it is the default ip address. If it is solid the IP address has changed due to a static assignment or DHCP.

  If no link light is on or the system flashes, the reason why could not tear out DHCP is due to a shift of port negotiation. Try setting the port on the router or the full 100 MB switch or what ever you like just to see if that helps.

  Make sure that you are also on the latest firmware.

  Try factory default of the switch with the button of reset for 45 seconds.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• Firefox prevents the connection from the router

  WRT120N router Linksys-Cisco, Firefox 22.0

  I discovered that my router rejects all attempts at connection (192.168.0.1, 401 authentication failure "browser can not perform authentication or authentication failed") when you browse to it from Firefox. It allows the connection when the attempt is made of Chrome.

  I remember having long ago something similar with Firefox, but resolved by disabling the option "say it me not to follow the sites", following what connections made; just looked and it is still not verified - if this isn't it.

  I looked a the packet capture and the password IS sent to the router, but it rejects the connection.

  Any ideas?

  "BUT IT WORKS CORRECTLY BOOTED IN SAFE MODE."
  Which prompted me to check the extensions.
  I called, guess what... TAKE STEPS TO TRACK ME.

  (Why is there such an extension if it is built in function?)

  Disabling, allowing the router to connect! I don't know why twice now, try to activate Do not not track eliminated the possibility to connect to the router... but this is the solution.

• Satellite A300 - unable to connect to my router

  Hi all

  I have a Satellite A300 and a Satellite A300D. Since a year im dealing with a problem and eat my heart. I have problems to connect to my router, for the moment I have a Netgear ADSL modem router wireless. When I am looking for a wireless network it seems to find the network, but when I want to connect I get the message network is no longer in the area.

  The distance between my modem and laptops are 3 meters in an apartment, even when im sitting on my router :-) this is not not possible to connect to the wlan. Tried to connect without any wep/wpa encryption, no effect. Played with communication channels @ the properties of the wireless network adapter and the router, but this isn't a solution.

  Before I got the Netgear, I had a Linksys / Sweex / Cisco pro / router Wlan from HP. I tried all brands of wlan, with all routers routers of this I had the same problem.

  Frustrating him of is that I can connect to my neighbors without any problem, but not my own network.

  Anyone having the same problem or know a solution?

  Have you tried to update the WLAN driver on two laptops? You can find it on the Toshiba site and I would update the BIOS too:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  What operating system do you use? If you use Vista, you must disable the WLAN to save energy card. You can do it in Vista Power Options.

  You use the same standard WiFi on your laptop as on the router? For example I mean project. G check this!

  At the moment it is not easy to say what is the reason for this, but I hope that I could help you a little. :)

• I'd like to find the password for my Cisco router

  I can't connect to my network wirelessly on my ereader, because I don't know what is the password when asked.

  Read the manual for the device (Cisco router) should tell you what the password by default is to manage the router (if this does not work... it should tell you how to configure the default router, so you can use the default password to reconfigure) so you can go and change the password to access wireless to something You know.

• 502 gateway incorrectly when you connect locally in router EA3500

  When I try to connect to my router using 192.168.1.1, or that the site is online, I get a 502 Bad Gateway and can't do anything. Internet works fine, but I can't configure the router.

  Things I've tried:

  Unplug the router for a bit, then reconnect.

  Factory reset the router with the button on the bottom.

  Using the android application to connect to the router. (Does not work, the router said wasn't online when it was clearly)

  Flushing DNS on the side of the computer, try different computers, trying different browsers, compensation hide browser.

  I tried to talk with Cisco via their online chat and found out that they are basically of crooks who want to charge you to fix things on the internet, but they told me that they believe it is a firmware issue and that I should update. I downloaded the latest firmware, but how do I update the firmware when I can not connect to the router?

  Hold down the button to reset for 10 seconds. The power led on the router will keep flashing for a few seconds after you have reset as it is still trying to stabilize. Once the power led comes on solid means that the reset is successful. Power cycle the router and make sure that the computer is connected to the router by an Ethernet cable. Remove the cache and the history of navigation on your computer, and then try again. It would be better if you can also try to access the page using another computer. I hope this helps!

• WD MyCloud NAS connection low or intermittent connection on new router WRT1900ACS

  I installed a new router WRT1900ACS to replace a former Cisco router and now I get a low or intermittent connect error message. Here is the error message I get:

  I have reflashed the latest firmware (1.0.0.169041), reset the router and set it back and from this moment, it seems to be. So I consider this problem.

• Why after connect to my router it take 1-2 minutes to load the router's Web site? No software and the hardware has changed.

  Why after connect to my router it take 1-2 minutes to load the router's Web site? No software and the hardware has changed.

  Hello

  I suggest you check out the link to Linksys support:

  http://homesupport.Cisco.com/en-us/support

• Names of the devices connected to the router

  How can I tell the names of the devices that are connected to my router E2000? Cisco connect says I have 4 devices but I only have 3. I'm trying to understand source of the 4 device.

  Open the Cisco connect software. Go to "Setting up the router" and click "Advanced settings". Who will open the router configuration page.

  Click the status tab. Go to the tab "Local network" sub on the button "DHCP Client table". Here is a list of the devices connected to the network.

• EA6500 unable to connect to the router after Time Machine

  Just got an EA6500 - updated to the latest firmware available.

  I have attached 2 x WD NAS and 1 x WD through the USB port of the device.

  Each time after I finished running Time Machine on the MacBookPro (written to one of the WD NAS), I can no more connection to the router as neither the local IP, or the cisco connect cloud. The error message I get (loosely formulated) is: unable to connect to the router. Please ensure that the router is connected to the internet.

  At this point, all the devices connected to the router (wired and wireless) still can access Internet perfectly. Only the console of the router is therefore more accessible.

  Anyone else have the issue?

  Any ideas on how to solve it?

  Contact support for Cisco and the person advised me to do a factory reset (even if the router is new with no customization!). Regardless, it now works correctly. Cisco Cloud Connect works always before, during, and after a Time Machine.

  "When in doubt, try to turn the grid and the.

• Cisco router linksys e1000 wireless

  a friend of my sister bought a cisco router (see the above subject line). Unfortunately, I was not home at the same time. Currently, there are a desktop wired to the router and a laptop with a Wi - Fi connection. The person who set up the router I forgot the username and the password of the router (didn't even bother to write this info). I convey my computer laptop home from work where I had a connection to internet/router. My laptop (Dell classroom business), I can see the two connections without wire (secured and unsecured comments). When I try to connect to the secure connection I do not get any screen of security, connection, etc., guests. He said something like 'try to check the security info' - do not remember the exact verbage. Anyway, I can not connect. The signal strength is strong - the bars are green. Can connect to the connection of comments, I am not always invited for any connection and safety info. Run the ipconfig/all command confirms the connection. I have still no internet access. Don't know why, but the signal strength readings 'poor' - a single green bar (while the secure connection shows all the force green signal bars). I have installed / configured several wireless - never had a problem.  I need to recover the connection info router without having to perform a hard reset on the router (I have same access limitted in my house of sisters/partners where the router). Is there a way to do it. I spoke twice to the cisco technical support and received two different answers (not according to the first call, open Explorer, go to programs/cisco for the info). This must be done on the computer that was used to install the cisco installation disc). Help, please!

  There are a lot of things I want to share with you on your router E1000 installation:

  1 E1000 comes with an installation CD that has CIsco Connect (the icon looks like a house) to easily manage your wireless network (you can easily get your password for the Cisco connection). Cisco Connect (CCC) is generally accessible to the computer that is first used to install the router (maybe this is why the tech officer ask you to go to the computer used to install this)

  2 E1000 broadcasts 2 signals of the main network and - network of comments. Once you click on the name of the network, you can easily connect the guest network seems to be unsecured However, when you access a Web site you will be asked a password. Always secure line.

  3. you can actually access to internet but not wireless cable but to the router.

  4. If you don't have the computer used to install the router, you must reconfigure and the first thing to do is to reset the router. You must configure manually if you do not have the installation cd.

  You can try these links:

  Setting up a Linksys router for DSL Internet connection

  Setting up a router with cable Internet Service