Low 6343 USB digital output

Similar Questions

• take the digital output USB-6001 always high or low in c

  Hi all

  I am new to the NI DAQ interface. I have a USB-6001 and I am trying to use this device to control some flowchart in C. What I want to do is:

  * set digital output lines with high and low intensity and change their status as needed (in C).

  I tested the device NEITHER Max--> Test panels and found that the device is capable to do that. Then I try to do in C. I have checked hace examples and function I use is one called "DAQmxWriteDigitalU32". I have problem in the understanding of its input parameters. I tried something with my own knowledge, but it does not work as I expected. Here is a test I did:

  data uInt32 = 1;

  Int32 wrote;

  TaskHandle taskHandle = 0;

  DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
  DAQmxErrChk (DAQmxCreateDOChan (taskHandle, "Dev1/port0/line7", "", DAQmx_Val_ChanForAllLines));
  DAQmxErrChk (DAQmxStartTask (taskHandle));
  DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,));

  taskHandle = 0;
  DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
  DAQmxErrChk (DAQmxCreateDOChan (taskHandle, "Dev1/port0/$line0", "", DAQmx_Val_ChanForAllLines));
  DAQmxErrChk (DAQmxStartTask (taskHandle));
  DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,));

  I just want to set ' Dev1/port0/line7' and ' Dev1/port0/$line0"at a high level, but only ' Dev1/port0/$line0' answer me. The second parameter of the DAQmxWriteDigitalU32 function is numSampsPerChan. If I replace (currently 1) with a higher value, such as 100, I see that "Dev1/port0/line7" sends a number of 1 output, then back to 0. So I guess that the problem is just that I understand not all parameters for the DAQmxWriteDigitalU32 function. Is someone can you please tell me how I can set up a line of digital output 1 or 0?

  Thank you!

  Hongkun

  Hello

  I finally find a way to do it! The feature works very well, and my problem was not set the data value to write correctly. It seems that if I want to write a 1 to the port0/line1, I put "data = 2 ^ 1" rather than "data = 1", because by default it is the second bit of the port.» Similarly, "data = 2 ^ 7 ' high level to port0/line7. I find that this setting is surprising when you want to control an individual line. It seems more reasonable when you control the whole port. In any case, is to solve the problem!

  Thanks anyway!

  Hongkun

• NI USB-6501 digital output problem

  Hello

  I use DASYLab v.11 and I'm working on an interface with the NI USB-6501 where I'm putting a digital high on four ports.

  With the module "NOR-DAQmx - digital input", I managed to read the digital inputs of the ' NI USB-6501 ".»

  It's only the "NOR-DAQmx - digital output" I can't go to work.

  Using 'NI MAX' of NOR I have easily can emmit my four LEDs in the way of my High/Low ports.

  But not with DASYLab. When you use DASYLab tension on the ports remains unchanged.

  Now, I have a switch module, generating 5/0, directly connected to the digital output module, which is assigned to my four output ports for my task.

  I also tried with a module of relay between the two without success. I also tried to use 1.5 above instead of 5 without success.

  I use the option 'Bus (0/5 supply) for the module "Digital output".

  "NI Max", I configured the ports as "active drive.

  Any suggestion of what I might be missing?

  Thank you

  Martin

  Hmm, four ports, or four lines?

  A port consists of eight lines. Each line can control an LED (ON / OFF ~ 0/5V).

  If you have created a task to dig-out to control a port, 5V to this port sending sets all lines of this port to 'high '.

  You need to 255 for each line one too high port (at the bit level: 128 + 64 + 32 + 16 + 8 + 4 + 2 + 1).<- eight="">

  Or, you can create a dig out tasks to control four lines of a specific port.

  Four lanes of the EEG DAQmx DigOut module.

  Each of the channels of the modul will feed a single line of the task/device.

  Four switches will then turn the lights, or turn off.

  Make sure, that the 'bitposition' is the number of correct line (see picture).

• Configuration of the digital output in the USB-6009

  I have a card for the acquisition of data USB 6009. It seems that him when DAQ card is turned on, it is always default to digital output of 'High' or 'floating '. I want to default to 'low '. Is there some setting I want to 'program' the hardware DAQ to have all the outputs low when it is powered on the value? Right now I have manually enter MAX and adjust the level 'low '. Thank you very much for your help.

  Sid05,

  Yes, it's low of 820 ohms. Unfortunately, the way in which the system is built, it is the only choice you have without having to build external circuits such as SnowMule suggested.

  AK2DM,

  Thanks for pointing the USB-6000. Finally a real, if limited, the DAQ hardware.  Nevermind, he was only 4 DIO lines.

  Lynn

• NI USB-6009 digital outputs are active when connected to a PC - I'm not that

  I have a small problem:

  All outputs digital NI USB-6009 module become active when the module is connected to a PC when no VI is running.

  As soon as I start my VI, which controls the module, all the outputs are disabled (now inactive).

  How can I achieve this, outputs are inactive if the module is connected to a PC with no program running?

  johanneshoer wrote:

  I have a small problem:

  All outputs digital NI USB-6009 module become active when the module is connected to a PC when no VI is running.

  As soon as I start my VI, which controls the module, all the outputs are disabled (now inactive).

  How can I achieve this, outputs are inactive if the module is connected to a PC with no program running?

  The USB-6008/6009 case has a pull-up internal (4.7 kOhm) resistance. This causes the outputs digital on the device to have a startup logic high State. t is not recommended to use some sort of resistance of menu drop-down. However, what you can do is add octal buffer like the 74HC541 stamp and a digital output to control the sorting of the 74hc541 state mode. Connect the OAS and CEO input signal. A Summit on the pins of the latter will be sorting the output of the buffer State. Therefore, no output signal will be present until you pull the stems of low control. The USB-6008/6009 case have a 5 volt output (200mA max), you can use the buffer.

• Pull-up external USB-6009. digital output (open collector) allows onboard external + 2.5 V output?

  Pull-up external USB-6009. digital output (open collector) allows onboard external + 2.5 V output?

  Hello

  I want to config output digital USB-6009 to + 2.5 V above and 0 V digital output low. I know I can config USB-6009 digital output open collector with resistance to pull-up external, that can be applied with + 2.5 V power source.

  My question is: can I use USB-6009 Board + 2.5 V output as the current source of resistance to pull-up? What resistance is a good number for the resistance to pull-up, if I can use this configuration?

  Thank you much for the help.

  Cathy

  Hi Cathy,.

  The digital USB 6008 front-end server looks like this:

  

  So, there is actually an internal pullup to 5V 4.7 kOhm resistance when the device is configured to open collector.

  If you want to display 0 to 2.5 V, I would look in a resistance of polarization of 4.7 kOhm between c and ground (according to the rest of your tour).

  Best regards

• USB 6008 digital output signal

  I am VERY new to LabView and have been racking my brain trying to get digital output of my USB-6008.  All I want is to be able to get a signal of + 5 V of my digital output when I click on a button.  This signal opens a valve on a system I see so when it is pressed, it must stay open until I press the new button.  It seems simple enough to me, but I'm not too familiar with LabView.  Help, please!

  Stripling07

  You must first take the LabVIEW tutorials and then look at the links to get started with DAQmx .

  The simplest program would be with the DAQ Assistant. Drop it on your schema, and then select digital output > digital line. Select the line when the wizard has completed, click OK. Wire a Boolean value in a table to build and the output of which is connected to the data entry. That's all. You can test the output of MAX (Measurement & Automation Explorer) with the test Panel. Do NOT test with your connected tap. Your valve may require more current that can provide the 6008.

  

• Implementation of multiple digital outputs with a box USB-6009

  Hi all

  I write the code to implement a USB-6009 multiple digital channels, digital outputs independent.  I have configured the function of "DAQmx create Channel" to create 'a channel for each line', but I can't understand how to access and control these channels separately.  Pointers would be greatly appreciated.

  Thank you!

  I thought about it.  Never mind.

• How to measure the digital output of the linear actuator on USB-6009?

  Hello

  I am a new user of Labview and need help to measure a digital input signal.

  I have an actuator Bimba Original line electric with a motor continuous integrated with encoder, drive and the controller. The drive has a programmable digital output that I put as a tachometer output that emits pulses of square wave 100 per turn of the engine. I put the engine to make a total of 56 rev in 22 dry. I want to measure the speed of motor rotation labview real-time and synchronize it with a few other analog input signals. I wired the actuator for the USB-6009 case as shown below.

  

  I opened the test i/o digital USB-6009 Panel and fix all the lines of port 0 as inputs. However, when I click on start and run the actuator, p0.0 led flashes, as indicated below.

  

  Shouldn't the led blink in response to revolutions of engines?

  I want basically to collect the drive pulse signals and convert them in rpm on labview.

  ahsan2 wrote:

  I have it wired correctly?

  It would help if you do not attach the HIGH signal.  Remove the + 5V in the circuit.

• USB-6211 - digital output not supported?

  Hi all

  I can't use the USB6211 device port... I use daqmx with Delphi7 API functions.

  First of all, I tried this:

  DAQmxCreateTask('', @TaskDO);
  DAQmxCreateDOChan (TaskDO, PChar('Dev1/port0'), ", DAQmx_Val_ChanForAllLines);
  DAQmxWriteDigitalU8 (TaskDO, 1, 1, 1, DAQmx_Val_GroupByChannel, $FF, @written, nil);

  I had an error in the DAQmxWriteDigitalU8:-200012 (= digital output not supported). (???)

  OK, I tried to disable autostart option based on DAQmxWriteDigitalU8 and insert a 'manual' start in the code:

  DAQmxCreateTask('', @TaskDO);
  DAQmxCreateDOChan (TaskDO, PChar('Dev1/port0'), ", DAQmx_Val_ChanForAllLines);
  DAQmxStartTask (TaskDO);
  DAQmxWriteDigitalU8 (TaskDO, 1, 0, 1, DAQmx_Val_GroupByChannel, $FF, @written, nil);
  DAQmxStopTask (TaskDO);

  Now, I got the same error in DAQmxStartTask:-200012 (Digital Output not supported, once again). (?????)

  I don't understand.. 'Digital output not supported "? USB-6211 has 4 lines! What is the problem?

  I want to just turn on and off the lines from code...

  -Cs George-

  Well, finally I figured out...

  Here is the solution:

  DAQmxCreateTask('', @TaskDO);
  DAQmxCreateDOChan (TaskDO, PChar('Dev1/port1'), ", DAQmx_Val_ChanForAllLines);
  DAQmxWriteDigitalU8 (TaskDO, 1, @dummy, 1, DAQmx_Val_GroupByChannel, @bitmask, @written, nil);

  Digital output lines are on port1! Corrected parameter.
  And the part of the interface of DAQmxWriteDigitalU8 had to be changed (in nidaqmx.pas).
  I don't know why, but the AutoStart (dummy) parameter in the DAQmxWriteDigitalU8 function is ignored: function always starts task automatically, regardless of the value of autostart. But this isn't a problem for me.

  -Cs George-

• USB-6008 to give the digital output

  Hi all

  I was wondering anyone at - it base an example of an exercise using USB 6008 to give a digital output of a VI in Labview.

  I am very new to the use of the USB 6008 AND Assistant DAQ and so far I've had reading a temperature, next step is I want the USB-6008 to give a + 5v output when the temperature reaches a certain value, I built a Labview 2009 VI for the temperature reading, but now I'm stuck on this piece.

  Any help is appreciated! or if there are examples of laboratory exercises that exist that I can perhaps draw.

  Hi Marko

  Please take a look at the link that has some interesting and intuitive video to use the USB-6008 housing and how to set up the device for several applications in LabVIEW below. Please take a look at the step by step videos and let me know how you go. They are under the tab '"virtual Demos.

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/14681

• Digital output of 6289 USB to the function generator

  Hi ppl.

  I have a DAQ USB-6289 card I use M series to interface with a programmable frequency AD 5932 generator (hope it's not breaking all the rules)

  In the datasheet of the http://www.analog.com/en/rfif-components/direct-digital-synthesis-dds/ad5932/products/product.html AD5932

  It is the interface series (FSYNC, SCLK, SURLABASEDESDONNEESDUFABRICANTDUBALLAST).

  I'm using LabVIEW to generate a digital output and help the Council 6289 to send the signal to the ad5932.

  The problem is the following:

  (1) I am an engineer in chemistry and new LabVIEW and electronics

  (2) I don't understand how the digital signal and the FSYNC SCLK and SURLABASEDESDONNEESDUFABRICANTDUBALLAST are related... Sorry for the very basic question...

  Hope that's not too much to ask, but if someone could suggest a tutorial or examples it would be EXTREMELLY appreciated...

  Thanks for any input because I'm really stuck on this point.

  See you soon

  You need to find is the complete technical data on the A/D. Who will explain what each of these pins and the time served. It looks like an SPI interface. OR sell the 8451 for this programming. You can or perhaps are not able to use the 6289. I recommend a search of "SPI" to see if anyone has created a VI.

• Is it save to use the digital output as a digital input for another channel signal

  Hi all

  I know it's a stupid question, but I don't have another generator of signals by hand. What I want to know is, can I use the signal digital output of my USB-6001 as an input for the same signal device, but on other digital port? I wasn't directly because I don't want to burn the device...

  Thank you

  Done all the time. No problems.

• digital output microsecond LED timer

  Hey all,.

  I'm doing a table of 10 LEDs in a row to form an analog timer to use to characterize the delay of the shutter on a digital SLR. We'll first stage shutter lag on the camera using a method different and well set the delay of the shutter for interior<1ms. i="" am="" trying="" to="" use="" labview="" alongside="" a="" ni="" usb="" 6251="" using="" an="" sc-2345="" for="" access="" to="" the="" digital="" outputs.="" im="" using="" a="" timed="" structure="" and="" a="" timed="" loop="" to="" ensure="" the="" timing="" between="" each="" led="" turning="" on="" corresponds="" to="" an="" actual="" time.="" however,="" i="" am="" not="" getting="" the="" results="" i="" thought="" i="" would.="" the="" timing="" does="" not="" seem="" to="" be="" what="" i="" thought="" it="" would="" be="" and="" i="" can="" not="" get="" the="" timed="" loop="" to="" work="" with="" all="" the="" channels="" at="" the="" desired="" frequency="" which="" would="" idealy="" be="" as="" high="" as="" possible.="" could="" someone="" take="" a="" look="" at="" my="" code="" and="" provide="" me="" with="" some="" insight="" where="" i="" may="" be="" getting="" issues?="" i="" apologize="" if="" i="" am="" overlooking="" important="" information="" that="" may="" be="" needed="" to="" help="" solve="">

  ~ Aaron

  I have no DAQmx I can't be sure.  I think that the 6251 has a maximum rate of 1 MHz in order to try to set the rate to 20 MHz should generate an error.  For the purposes of test on the rate 1 Hz bit or less.  Then you should be able to see the LEDs as turning on and off.

  You may also need to set the number of samples to the size of the array.  Referring to the size of the array fed to Scripture DAQmx, not the table on the front panel.  With the number of samples set to 1, I would expect that he wrote that the first element of the array that is equal to zero.  That does not produce a very interesting performance: he lets just all lights off the coast!

  Lynn

• Digital output is not 5V when connected to a circuit

  I have a very simple circuit I want to operate a valve. I have a NI USB 6008 with 12 digital i/o ports, a KF0602D solid state relay, 12V power and a solenoid valve.

  The idea behind this circuit is pretty simple: use a digital line of the 6008 to close or open the switch in the KF0602D. With the switch closed, current flows from the power supply through the switch, to the valve and that opens. When the switch opens no current flow and the valve closes.

  When I plug my 6008 in the KF0602D, however, my 'high' digital output falls from 5V to 1.73V. It's a problem because my switch requires at least 3V to close. I don't know why the voltage decreases because the relay is supposed to just on 3mA current with an input 5V, wells in the area of the specs listed 6008. What can I do to make this work?

  Outputs digital USB-6008 are drain opened with pull-up 4.7 kohm resistors. This will NOT lead your SSR entry requiring > 2 my.

  He must reverse the polarity of your control signal. Wire-entrance of the Republic socialist Soviet to the line of the 6008.  Wire the + input of the Republic socialist Soviet to + 5 V. Then you have the 8.5 my driving ability to do what you want.

  Lynn