M127fn LaserJet MFP Pro: Hp Laserjet help

Similar Questions

• HP Color Laserjet M177FW MFP PRO cannot connect to web services

  I bought a HP Color Laserjet M177FW MFP PRO today and took me to the top. It can print and scan over wireless network. However, it cannot successfully connect to web services. I put the DNS numbers with google DNS addresses. I changed his IP address with manually. The IP address is unique. Normally it is not activate/remove webservices. But when I restart it, it can do for a few minutes. It may take an e-mail address, but it does not print any information sheet. When I try to print a sheet it says "Connection problem" in the first minutes, and later, he said "Connecting" and he expects, there is no error message. What am I supposed to do? Please help me.

  First of all thanks for your help. I solved my problem. After that I sent this message that I've updated my firmware printers and that does not solve the problem. I called HP customer service and they help me. We have solved the problem. My router was the reason for my problem. When I reset to factory settings, the problem disappeared. Thanks anyway. I want to share my solution. Maybe it helps others.

• Color LaserJet MFP Pro 277dw: MFP will print but not scan since update Mac OS 10.10.5

  I had used my LaserJet MFP Pro wireless without problem for several years, with the Mavericks and Yosemite.  A few weeks ago a "update" the printer system is invisible.  After several hours of troubleshooting and to try five or six corrections, I finally got the printer online by using the IP address.

  My computers, however (a performer of the Mavericks and a Yosemite running), do not see the scanner.  It's not a question of adding - they do not to add it.  By HP support, I have reset the system print and tried to start over.  I downloaded HP Easy Print (or Easy Start or whatever), which is the entire site of support in the way of software for the 277dw of the ACM.  The software through me the entire upward and congratulated himself for a job well done, but my printer was not, in fact, related.  He appeared in the printers Control Panel, but would not print.  Just "connecting to printer" in the queue for ten minutes about until what I called off work.  And the scanner does not yet show in the Image Capture, preview or HP Easy Scan.

  So, I went back to my previous fix for the printer, use the IP address.  Any ideas on how to get the scanner appears?

  Hello

  Restart your router by unplugging its power for 30 seconds.

  Once it is fully up and you have internet access on your Mac reboot both the HP printer and the Mac.

  From system preferences, select Printers and scanners and click on the plus sign to add the printer again.

  Can you now ee he listed as Hello type or not?

• HP Color LaserJet M177fw MFP Pro - support PostScript?

  Hello

  I am looking to buy a new printer/scanner/copier(/fax is a nice to have, but not mandatory), and I am deciding between the following models:

  HP LaserJet Pro 100 color MFP M175nw

  HP Color LaserJet M177fw MFP Pro

  PostScript support is important to me, and I know that the 175 has it.  However, I'm not sure I know the 177, even after digging through several web pages and documents.  Here's what I found:

  -The page of the main form for the 177 says that he accepts "Cffp.  I'm not familiar with this variant PCL, so I don't know how it compares to PCL5 or PCL6, etc..  I have been unable to find more information about "Cffp.

  -The 'Software' section of Page 2 of the PDF Datasheet for the 177 mentions the driver "HP PostScript".  This is the only place where I saw no potential indication that the 177 supports PostScript.  This article also mentions a driver "PCLmS".  I couldn't find more information about "PCLmS".

  -The user 's Guide the 177 refers only to PostScript in an article that refers to ePrint.  However, it does not imply that the 177 itself supports PostScript.

  -Page product specification (in the Support section of the HP site) for the 177 has a "Print Specifications" section which lists only "PCL3 GUI" next to "languages of device.

  I'm guessing that the 177 is not compatible PostScript, but someone has the more definitive information?  Also, is there a description of the Cffp / PCLmS somewhere?

  Thank you!

  Hi Clent

  Here is some information on both printers.

  Here's a url for the printer for Color LaserJet MFP M177fw Pro specifications

  http://support.HP.com/us-en/document/c03901180

  Data sheet also.

  http://www.shopping.HP.com/shopping/PDF/cz165a.PDF

  Fonts and fonts depends on fonts and fonts in OS.

  Print language

• Jam - HP Officejet 8500 pro error - please help, deployed without return option

  Jam - HP Officejet 8500 pro error - please help, not deployed to M.E. no return w/lovely HP option

  I have a month old HP Officejet 8500 Pro, which suddenly give a paperjam error message.  There is no paper jam.  I spoke with HP Technical Support making long resets even blow the bowels to air without result.  It must be a simple mistake.  I saw it reported on other boards, but it seems that everyone is simply trading on their printers.  Not an option, like HP, in their infinite wisdom will not replace a defective unit overseas.

  I thought that there is a paper feed guide that hung above the paper tray.  It's hangin' is low... but maybe I was mistaken. If I tilt the printer back it will feed and eject a page, but not print.

  If someone at HP would be so likely to enlighten me I would willingly do what is necessary to take part, or whatever...

  Help... Help... Help...  Thank you...

  Here is a link that will help you.
  http://goo.GL/vxhuH
  
  It may be a sensor that went bad in the printer that generated the message.

• HP LaserJet M127fn MFP pro: printer works is not after a few days

  Hello I have a printer model: HP LaserJet MFP M127fn pro

  I installed the software and drivers and the printer works perfectly well for a few days and then stops working. I have then uninstall and reinstall the drivers working yet and only a few more days...

  Someone please guide what to do...

  Thank you

  Hi!, guy36:

  Please see... http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Introduction

  Step 1

  Step 2

  Step 3

• Printer HP laserjet MFP Pro M127fn & 125: we have a big problem with this printer

  We have 20 printers or more M125fn and M127fn, we have problem with printing on the fonts Geo_Times, Geo_Times "BOLD", Geo_Times Italic, Bold Italic Geo_Times, we have programs that work on this policy and no one can print the text on this subject, please help us with this problem.

  Hello

  What program you are trying to print from?

  Printers use language to print Cffp, it will help to know the program to make sure that it does not require a more advanced PCL 6 printer

• LaserJet M127fn MFP Pro: Printer not connected

  Hi all trying in vain to connect the printer to a wireless router. USB connection to the router; router, Asus DSL N55U; configuration of the router page lists the active printer. That's all. Printer shows on self-esteem / Test as "unrelated", no IP address. What can I do to connect? Thank you very much for your time.

  I have this issue sorted by myself earlier today. Here's what I did. I have reset the printer by cutting the power supply and leave it unplugged for a few minutes. I've deleted all the software my laptop prnter installled. As opposed to the connection via USB, I connected through the ethernet on the printer port to one of the four ethernet ports on my router. Then I powered and immediately noticed a light on the router indicated connection through one of the ethernet ports. My wife came running downstairs to tell me that she could see the printer listed on his iPhone. After a few minutes, I ran a report of connectivity, and it showed connection and TCP/IP connection details. I then installed the software. I am happy to say that he works all famous and we are happy campers.

  Thanks for your help.

• M127fn LaserJet MFP Pro: Installation of the LaserJet MFP M127fn Pro software

  I installed the M127fn as a network printer on 5 machines without problem, MAC, Win Vista, Win 7 and Win 8.1 (2).  However on another machine, also running 8.1 Win, preparation for installation is at 73% and fails with the following: "error A problem occurred when the preparation install the software in your system."  If please restart your computer and run this installer again.  If the problem persists, please visit the web site of product support for your product. "She does it with both the software on the CD as well as the version of downloader.  I'm her disabled administrator with Norton Internet Security and Malware Bytes.  I used the uninstall on the CD several times to remove any partially installed files does not.

  Using Windows update solved the problem.  She provided 2 updates pertaining to the M127fn.

• M127fn LaserJet MFP Pro: Printer/Fax stuck on 'Printing Fax page 1'

  My business fax machine is stuck on a screen that says "Printing Fax Page 1". I tried to unplug it for 5 full minutes and it does not clear. How can I reset the printer/fax?

  There are a growing number of messages in this forum and elsewhere in the internet with the steps to do a reset on different printers.  Reset to will sometimes fix problems, so resetting is not the issue.

  A few resets require you to enter key combinations to open special menus on your printer that you were supposed to never access.  These special menus are used by developers and staff support for debugging of problems, but they are not intended for inexperienced users and can have unexpected results.  A wrong button push and you might no longer have a printer, but rather an expensive paper weight.  On top of that, if you happen to the 'brick' the printer in this way, it is considered as customer induced damage and voids the warranty automatically. These resets are only intended to be distributed and used as a last resort and under the direct instruction of a representative of the HP technical support. They should not be made lightly!

  Printer resets: What You Should Know by @Bob_Headrick

  Please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  Please take a moment to read the privacy policy of HP to http://www8.hp.com/us/en/privacy/ww-privacy.html this privacy statement informs you of our privacy practices and the choices you can make about the way information about you and your online business is collected and how that information is used. This statement is available on our homepage at the bottom of each web page of HP and HP.com.

• HP LaserJet MFP Pro M127fw Installer has stopped working

  Have difficulty installing drivers HP LaserJet MFP M127fw Pro portable 32-bit hp with windows 7

  Build in software printer stops at Midway

  Downloaded software stops at Midway

  Printer driver standard windows 7 works very well and can print with it, but has no scanner driver

  Doctor scanner HP printer indicates the scan software is not installed and directing me to download driver on the hp website

  installation of this software also stops at Midway

  No errorcodes anywhere, box Installer just message could not continue and try to find a solution. This box diapears as well.

  Installation fails on cable network and usb

  no error messages in the logs of windows

  The http connection works fine

  tried installing with smart installation on and outside (is disabled for the moment)

  Spooler service works well

  We searched this forum more people seem to have this problem but there is no solution mentioned in the end.

  Help, please

  @Gemini02

  Thank you for your help.

  I'm afraid it does not either, I don't use McAfee but Avast.

  Stop Avast, or stop the firewall (windows standard) does not resolve the inability to run the installation software.

  If I unplug the USB cable, the virtual CD in the printer disappears and so cannot run uninstall.

  I didn't want to stop all services, because I don't know what he must stop and don't want other problems that may be difficult for me to correct after a reboot.

  Also, I didn't want to install as administrator, I cannot guess.

  My solution that worked in the end is:

  Connected the USB cable.

  A printer icon appears but with red crosses indicating missing and software scanner fax.

  Right-click on this icon of the USB printer and select software update. the research on the internet.

  Downloaded and installed the correct software without problems.

  I cannot now use the scanner software using the network (wired), but I can live with that.

  The printer works fine on the network. Scanner only via USB.

  Again, thank you for your help.

  This band of turnover can be now closed.

• Color Laserjet Pro M177fw MFP: HP Color Laserjet M177fw MFP Pro cool mood after printing all pages.

  I bought Color Laserjet MFP M177fw Pro for only 3 days. From the beginning he said impression... mood of cooldown and take a long paus. This issue takes place after printing each page. I use HP Toners. And my related directly to the wall socket (Electric).

  Please help me. It is urgent for me.

  Thanks in advance.

  Hi Ryans,

  Please check private Message

  I hope this helps you!

  +++ Say thank you by clicking on the star of congratulations in the post.

  Although I am an employee of HP, I speak for myself and not for HP.

• HP LaserJet MFP M-125 Pro has: MacBook Air connected to a Laserjet MFP Pro but does not print

  Hi, I'm trying to print from an HP LaserJet Pro MFP M - 125 bis, which is connected to a MacBook Air via a USB cable. The software has been downloaded and the print job is always show that if it is trying to print the given print job but no print is issued and the print job is considered fact. Can you please tell me what is wrong why the print outs coming out?

  Hi @Lilium,

  I see you are having problems printing via the USB connection. I would really like to be able to help solve this problem.

  Did you download and install the software solution full or run Upates Apple?

  Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (LaserJet MFP M125a Pro)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  How is the name of the printer listed?

  If the problem persists, try the following steps:

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

  Try to print again.

  If you need help, let me know.

  Have a great day!
  Thank you.

• HP Color LaserJet M177fw MFP Pro - beeps periodically

  My M177fw took to beep once every 8 hours or more. I don't see anything in the newspapers, at least when you look at the internal web server to the device. He tries to point out an error?

  Thank you

  Allen

  Hi @DABJR ,

  I see by your post that the printer emits periodically. I would like to help you today.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Update the firmware of the printer. HP Color LaserJet Pro M177fw MFP drivers.

  Select your operating system, click Next, click the link for the firmware.

  You may need to set the time to sleep and define the sequence of events on the printer.

  Touch control panel:
  1. from the home screen on the product control panel, press the Setup button.
  2. open the following menus:
  The system configuration
  Energy settings
  Sleep/Auto Off after
  3. Select the time for the delay of sleep/Auto Off.
  NOTE: The default value is 15 Minutes.
  4. the product automatically wakes up when he receives jobs or when you touch the screen on the product
  Control Panel. You can change events make the product to wake up. Open the following menus:
  The system configuration
  Energy settings
  Alarm/Auto on events
  To disable a factor of reactivation, select the event, and then select the option.

  This information was given by the manual on page 59. Multifunction COLOR LASERJET PRO.

  If you need help, let me know.

  Have a great day!
  Thank you.

• Driver for HP Color LaserJet MFP Pro M PCL 6

  64-bit driver for HP Color LaserJet Pro MFP M477 PCL 6: I have one of these printers, which is able to print double-sided automatically.  The new driver (64-bit) will not accept when I switched to a new laptop, manual duplex printing.  Does anyone else have this problem?  I updated the driver, but the problem persists.

  I managed to find the solution... it is a lot harder than I imagined composed I don't remember clearly how I found it.  But I think it's what you do... Use the control panel to get to the devices and printers, right-click for properties of the printer, then select device settings, then select installed in the duplex unit.  Yes... complicated.  How the average dumb guy like me never to solve such a problem?