memory diagnostic problem

Similar Questions

• Pavilion Notebook: Windows Memory Diagnostic

  I ran Windows Memory Diagnostic a couple of times and it returns a message of hardware problems must be addressed by the manufacturer of the computer.  He said that when the diagnosis ends, there will be more information available.  However, the diagnosis is never ending. (I let rest 3% overnight) I started the diagnosis of memory because of a BSOD on Windows 10.

  Old man.

  That signals that it doesn't have the memory module in the lower position.

  Replace it and the problem should be solved.

• Memory controller problem?

  My new X230T works well for most, but I also had the odd problem here and there, who seemed at first view to focus on the SW.  However, memory is "basic" Windows Memory Diagnostic, but crashes at 21% when I try to run this "extended".  Since the results are the same with 3 different memory modules, including 2 worked in another laptop, it looks like a problem of controller memory.

  Lenovo support advises me send in the laptop for repair, but I wonder:

  1. If it is a problem of synchronization of memory, which can be fixxed by updating the BIOS.
  2. If it's even safe to try to update the BIOS; probably the problem of memory could cause errors in the update.
  3. If I should restore the laptop to the original configuration before you send it.
  4. If it is safe to use a backup (Clonezilla) image to restore my system configuration when I get home again, or if I have to reinstall / reconfigure everything from scratch. no doubt he could stand errors in the image backup or the configuration SW caused by errors of memory, but it took several days to get to this configuration.

  After reading some other posts on the web, there seems to be a known issue with the Windows Memory Diagnostic progress indicator.  Although it only takes seconds for each increase of 1% up to 21%, the indicator can subsist on 21% for hours.  Is not necessarily an error, and the test can still complete successfully.  I'll let it run all night and report back.

• Windows Memory diagnostic of hangman to halfway...

  Using Vista Home premium SP1, computer laptop lenovo Y430

  during the analysis of the diagnostic memory tool he successfully scan first part but hung on the second part @ 25%. Tried using the ESC key no response... After a while you press the power/button switch and he died.

  Was able to start again without any problems. However, when access some admin like computer Mgmt tools > service and application > an error msg appears and forces me to close.

  After the start, I scanned the two disk (C, D), no errors/bad sector, defragmentation = ok, ok = Sys file checker.

  I don't know smething wrong, someone at - it ideas?

  the error msg (WMI)

  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.

  TKS.

  Since you memory diagnostic failed which may tend to indicate a memory problem.

  www.memtest.org has a free bootable memory utility test

• Black screen after using Windows Memory Diagnostic

  Recently I have experienced problems with the system restore doesn't work don't not and although perhaps it was the file system and so I started Windows Memory Diagnostic and didn't know that you need to manually restart the computer and so I tried works again and again until what it finally hit me that I needed to restart it myself. He began to do his thing and I left a little to return to a black screen at 3:30 and it is now 23:00 and still nothing has changed. Don't know what to do and I don't want anything corrupt or damage my computer anyway. Is it normal for her and if not, how can I stop my computer safely?

  Hi Brendan,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver.

  I suggest you use the steps in this article and check if it helps.

  Reference:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• How can I know what that found Windows memory diagnostic?

  There is a small box that says.

  "your computer has a memory problem" "memory problems can cause the computer lose information or stop working." To identify and fix the problem contact the manufacturer of the computer "."

  Y at - it somewhere I can look and see what she got?

  I had all kinds of problems such as, blue screen memory dump, google chrome aw snap crash a lot, I was playing a game and it crashed to the desktop, so I couldn't run all the programs with reformulating them the computer, the computer no longer meets the Middle Windows up to date.

  When these problems started I thought ok I have this Windows 7-64 bit running for 3 years so I have re installed every thing and the same thing happened, I did it again but this time I used my XP disk to do the long format, it took 6 hours to do the 2 to hard drive if there are viruses that should have killed them and the reader should be as close to new as I can get it, but I still have the same problems.

  I ran scan disk, no problem, right now my CPU usage is 6%, RAM is 1.78 GB used out of 8 GB on the Task Manager.

  My computer performance scores are

  Processor 7.2

  7.4 RAM memory

  Chart 7.4

  7.4 games graphics

  Hard disk 5.9

  It says I have a memory problem, but I've never seen more than about 2.8 GB of RAM being used I think that my motherboard is wrong something to do with the LAN of the jury party because all the problems seem to have something to do with the internet, but I would like to know what she has in case it's the hard drive and not the Mo before as I have spend a lot of money on the bad parts.

  I have try ed out the RAM and put back in, run the test, but did not so bad yet lucky, so I took the RAM on another PC and TA-DA! She has passed the test and everything works now no more of accidents.

  It would have been nice if she was 'Diagnostic memory Windows (RAM)' instead of memory diagnostic Windows user so first like me knows just what memory it is testing, I found by chance and didn't know what it was.

  So if your browser blocks a lot especially google chrome "AW snap" crash and accident of programs on desktop to run this tool, it could be your RAM.

  I hope this may help others.

• Memory Allocation problem when using JNI

  For a project, we need to interface Labwindows CVI / Teststand with an application written in Java. We use JNI. The code uses JNI_CreateJavaVM to start a JAVA virtual machine to run the Java interface code. The code did run for quite awhile, but now (without any obvious changes on the side of the CVI or on the coast of Java) JNI_CreateJavaVM will fail with the error-4 code, this means that of the JAVA virtual machine failed to start due to the failure of allocation memory. First investigation shows that even if the Windows Task Manager shows approximately 600 M free physical memory, you can allocate in ICB only about 250 M as a single block at the point where we call JNI_CreateJavaVM. Maybe it's a little less because we have - Xmx192m to the JAVA virtual machine to run our code. Unfortunately just to increase the physical memory of the machine of 1.5 G to 2G doesn't change anything. Free memory space in the Task Manager showed increases, but the memory total block size does not work. Are the trick to optimize the CVI/Teststand who use cases?  Or maybe the problems with JNI?

  Finally, it was a memory fragmentation problem with TestStand. See details/solution here

• Closed during the operation "memory diagnostic tool"

  Using WINDOWS Vista HOME PREMIUM.

  When I run the 'memory diagnostic tool' the computer stops half way through the process.

  He stops at a different % of how the process every time.

  It also stops when I make a video file.

  The rest of the time it works OK.

  Can you suggest a reason or solution for this?

  Maybe it's overheating when you perform CPU intensive tasks. Check the dust accumulated around fans and heat sinks. A can of compressed gas can be used to remove items.

• I ran the Windows memory diagnostic tool, he keeps repeating and will not be finished, finally Boot Manager Windows appears with the error code: 0xc000000d.

  I ran the windows memory diagnostic tool on my PC toshiba laptop equium, it restarts priming for display and then directly into the RAM test...
  Unfortunately, it will not end and keeps repeating and finally if leave to work for a few hours the Windows Boot Manager comes in and stops the RAM test while noting an error 0xc000000d code. I REALLY can't reformat what I have given crucial for the thesis of the University and I only have the Vista installation disc not repair...
  This RAM test shows whenever I start the PC, how can I forget that he spent his RAM test a pc and more? I'm so confused!

  Any ideas on how may get a repair disk or fix it otherwise? Thank you very much

  Run Memtest86 +: your computer passes this test?

  Memtest86 + is running from a floppy or CD and should eliminate or confirm if your one or more of your sticks of memory are bad or the values of the SPD in the BIOS are correct.

  Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), if no errors at that time then your ram is OK.

  http://www.memtest.org/
  Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
  http://www.overclockers.com/forums/showthread.php?t=409152

  J W Stuart: http://www.pagestart.com

• Windows memory diagnostic tools does not work

  Why doesn't windows memory diagnostic tools?

  www.memtest.org . for a free bootable memory testing utility

• POWEREDGE 2800 memory/battery problem

  Hello

  The server DELL POWEREDGE 2800 our company with windows sbs 2003 suddeenly server has restarted yesterday and stuck in the POST gives the error"

  Memory/battery problems were detected.

  The adapter has recovered, but cached data have been lost.

  Press a key to continue. "

  I have three times restarted the server by pressing a button to continue. All three time loading of bones preserved for a long time and restarted the same screen of the error.

  ATLAST I turned off the server and checked for any loose contacts according to the suggestion of dell. I removed the disk 0, 2 HHD, HDD3 in channel one o and replugged in and started the server. Same system has occurred. 1 HARD disc is already failed in RAID 5 and the place so that the disc is empty, I suspected may be another disk HARD in the same row is a failure and so I removed HDD 0 and rebooted the server. the same symptom (2003 loaded and stuck). turned off the server ' reconnected HDD0 and removed HDD2 and restarted the server, but the same symptom.

  Reconnected the HDD 2 and disconnected HDD3 after restarting the server, it gives error loading operating system.

  There are disk HARD 4 and 5 two more hard drive HARD drive in another channel 1

  How to recover from this problem and our secure server data?

  Please help me with this because I'm helpless and the server must be brought im production tomorrow

  Thank you & best regards

  Margot

  If your LCD is blue and you get the error of memory/battery on each startup, then you need to replace memory RAID (99% chance that it is rarely a defective battery or the riser).  The operating system will not usually start in this scenario.

  If your LCD is amber and a message about the scrolling ROMB battery voltage, you should replace the RAID battery (sometimes it's because of riser).  The operating system will usually start and work very well in this scenario.

  First of all, stop playing with readers and replace the memory RAID (and battery and lift to be 100% sure).  Once it is replaced, due to all mixture player you have done, you might have a few steps very careful to recover your data and make your table online.  When you're ready to do this (again, it is useless before repairing the message memory/battery), call Dell technical support - it's always free on servers, regardless of the status of the guarantee.

• memory day problems post 10.11.6?

  In the last days, safari has been giving me the BBOD, and crashing several times a day. Less critical (but hey, it's a holiday weekend) lies in the fact that I can't play the games (minecraft) because the application continues to run out of memory, despite the fact that I have 32 GB of ram. There is a process of kernel running at the level of the root that starts normally, but then the spikes to use all available memory (less than 2 GB to 18 GB - Yes gigabytes is - and all applications must be suspended at this time).

  Does anyone else have problems of memory after this last update? I don't think it's a coincidence that safari, memory and kernel of processes are involved in updates and my problems, but I am not an expert. Anyone have any ideas?

  I'm running an i - mac 2013 with 3.5 GHz intel core i7:

  

  

  AnneMarie

  < re-titled by host >

  Please download and install EtreCheck from http://etrecheck.com/

  Run it and post the report here.

• Stops at random - memory/battery problem?

  Hello

  I use a Macbook Pro (retina, 13-inch, early 2013) and OS 10.11.3

  Recently I had problems with what I thought it was my battery... The laptop randomly stops (if not connected to the power supply), usually when it is less than 50% charged. When I then connect it to the power and turn it on, my date and time was given to zero on January 1, 2013 or something.

  It becomes more and more difficult to work with, and it seems that the percentage that he dies gets higher. Sometimes I have an error message saying 'Battery of Service', but sometimes that happens and is not at other times. My battery had only 300 cycles, so I'm a bit puzzled as to why this is happening.

  In any case, just to be safe, I ran a test for Apple hardware, and I got this error: 4MEM/61/400000000

  That seems to say that there is a problem with my memory. I don't know if the problems of memory can cause such shut downs, or if it's my battery. I don't really want to take in battery life if she will come out with the same problem.

  Thank you very much for your time and help.

  Please take the computer to the Apple store to have the computer checked.

  The Genius Bar reservation:

  http://www.Apple.com/retail/Geniusbar/

  Best.

• Satellite A660 - 11 M - Memory Upgrade - problem

  Hello world!

  I'm having a problem with upgrading my RAm 4 GB to 8 GB memory ([link crucial 8 GB Kit | http://www.crucial.com/eu/store/mpartspecs.aspx?mtbpoid=28543EEAA5CA7304]) which should be compatible.

  When I turn on the laptop after mounting of the modules to all first all seem to be right and the Bios start, but then it will not load windows and stucks on a black screen.

  Could someone help?

  Thank you!

  Hello

  What to say: it looks like it s a problem with new RAM modules.
  The RAM modules aren t fully compatible or they malfunction.
  You must use other modules I made good experiences with modules from Kingston.

• HP Envy 850-065SE: memory upgrade problem

  HP computer: Envy 850-065SE (memory 4 locations)

  Memory: G.SKILL RIPJAWS V F4-2133C15D-32GVR DDR4-2133 CL 15-15-15-36 v 1.2 2 * 16GB

  I just bought 32 GB (2 * 16) G.SKILL RIPJAWS V F4-2133C15D-32GVR DDR4-2133 CL 15-15-15-36 v 1.2 memory to upgrade my HP desktop computer (model 850-065SE of envy). My office has a HP mother 2B3A and i7 - 5820 k and HaswellE chipset. The memory of the plant is of Samsung brand with configuration DDR4-2133.

  When I replaced the memory of samsung (trademark) with G.SKILL ones, the computer cannot start with black screen. When I've switched back to factory memory, the computer is back to normal.

  That means G.SKILL RIPJAWS V 16 GB memoryis is not compatible with this HP computer motherboard? or upgrade the BIOS can solve this problem? or do I return these memory and get 8 GB * 2 instead? Your comments are much appreciated.

  This model is limited to only 4 GB and 8 GB modules in the slot.

  B21 HP

  CL15 - DIMMs, 4 GB, PC4-17000, 798033-001, DDR4 COMPLY_2.07

  CL15 memory - DIMM, 8 GB, PC4-17000, 798034-001, DDR4 COMPLY_2.07

  You can buy online modules of 8GB.  Look at the technical on this point.

  https://www.CDW.com/shop/products/Kingston-DDR4-8-GB-DIMM-288-pin/3912220.aspx#Po