MX920 printer error state

Similar Questions

• How to fix "Printer error state" when I try to print to the HP Laserjet 3030?

  Have not been able to find information on why my HP LaserJet 3030 printer cannot be used with the new computer from Samsung in Windows 8.  I chose driver for printer, but receive error messages - "Printer error state" or "Cannot find the output device" - when I try to print.  What can I do to fix this?

  Unplug the printer for PC > uninstall all printer drivers > restart PC > down load & install the correct driver from the HP Web site > reconnect and turn on printer:

  http://h20000.www2.HP.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=378058&TaskID=135&cc=us&lang=en&prodSeriesId=378056&prodTypeId=18972

• Printer error state now that I downloaded windows 8! lose patience!

  I downloaded Windows 8 and now I have my printer canon used print

  Cannot communicate with the printer printer error state, and indicates

  Turning on bidirectional printing, which deselects itself instantly.

  Please help I'm losing my mind and must be able to print!

  Carole

  Hello

  I deleted the driver no Ospreys wing and re installed! Finally
  The printer works now!
  Thank you for your help - you have saved both a visit through the window
  Carole

• How to fix "Printer error state" win8 / win8.1 (late printing) looks like all hp printers to still occur.

  This takes place too may long to count. Impression of Windows 8 and 8.1 works 85% of the time but time hp office then "printer error state" 8600 pro.

  See these same problem. Uninstall is just a miracle same problem will return. Looks like that happens at expiration, then the pop-up message. He wants to cancel printing. I just put and wait (X) the box pop up. Soon the print job comes into play. It is trouble of software product. Not HP readers or hp software. I tried may fix. I just cleaned up PC to format min. installed programs is the same as the old hard drive full of junk.

  Hi Tony,.

  Please contact Microsoft Community.

  This problem may occur if one or more are true.

  • No more paper.
  • Print the door is open.
  • Course of Toner.
  • Paper Jam.
  • In offline mode.
  • Hot Bus error.

  I suggest you to follow the instructions below and check if it helps.

  1. Make sure that the HP printer cables are connected properly. If in doubt, turn the printer off, unplug the unit and unplug all cables from the printer. Plug it back and reconnect the cables. Turn the printer back on to see if the error is cleared.
  2. Check the HP printers cartridges and printheads to ensure that they are properly installed. See also if the cartridges are empty. If the ink cartridges have ink, reinstall the cartridges and print heads. If the cartridge is empty, replace it with a new one.
  3. Make sure that the HP printer software is installed correctly. If the device does not respond when you try to print or printing software will not initialize, uninstall and reinstall the HP printing software. Refer to HP Officejet Pro Full Feature software and driver.
  4. Clean and align the cartridges of printers. Open the software for your HP printer or HP solutions Center to access these features of maintenance.

  We answer with the result, then we can help you further.

• Error in XPS Viewer in error status Windows 8 - "V4 Microsoft XPS printer error state"

  I added the printer XPS v4 to the list of printers in the print dialog box.  When I try to print to the XPS printer I get "V4 Microsoft XPS printer error state".  How can I fix it?

  Hello

  See the following link, it might help.

  Change the default Format for Microsoft XPS Document Writer.

  http://TechNet.Microsoft.com/en-us/Windows/hh859698.aspx

• HP Envy 4507: Printer error state

  Hello

  My printer does not print.

  He said that it is in "a State of error."

  The blue light is on that indicates it is bound upward to wireless technology. When I click on the button live wireless it says on.

  It prints a copy of the end scanner.

  It allows to print test messages that says:

  No problems found.  Congratulations for the success put in place of your wireless printer.

  Wireless on - pass

  Wirelss work - Pass

  Signal - Excellent quality

  Connected - pass

  Network name - found pass

  Chanel - 11

  All this is pass.

  Current configuration:-connected to the Internet.

  I can't understand what is wrong with it!  It works as well, because I got it about 2 months ago.

  Please can someone help!

  Welcome to the HP community @marinag,

  I wanted to respond to your message on the error state error message you notice about your envy 4507, to see if we can reach a resolution for you.

  You can make standard copies at the front of the printer, which does not imply the computer somehow. Because the working copies, the equipment is correct.

  You mentioned that you are also connected the printer to use wireless Direct, which means that the printer will not be able to print when you are connected to the internet, so this may be a problem.

  Wireless printing Center (Direct wireless info)

  Maybe try disabling wireless live by accessing the Setup Menu or the Menu on your printer wireless. Turn on the printer and then connect the printer with the following instructions to connect to the wireless network.

  HP ENVY 4500, HP Deskjet 3540 printers - printer wireless (Windows) installation

  If you have any questions, please let me know and I'll do my best to help!

  Testify of my answer by hitting the thumbs below and press the button "Accept as Solution" if I've helped to achieve a settlement.

• HP deskjet 1010 series: printer error state

  My printer is in an error state, but after doing the thing does unplug, I can now print the test print. Everything is beautiful nut when I tried to print some documents in my email, it says printer is in an error state. I just nothing can not print from my email, it's paper or the size setting? Can you giveme an idea what it takes then please.

  Hi felicity1,

  Can you tell me what the specific error or an error message is so I can help you?

  Thank you

• Printer HP Photosmart 7525 says printer error state.

  Original title: printer in an error state

  I've been printing with success of my Pro Surface using my printer HP Photosmart 7525 for a few months.   However out of the blue I got a message when I click on the printer that the printer is in a State of error... that's all.   I went to the HP website and print successfully a step printer HP Network Config report. Page and test wireless report.   No problems here... all printed.   Also made the deactivation/activation of printer etc..   Any suggestions?   Thank you!

  Hi Sandy,

  Thanks for posting your query in Microsoft Community. I see that you have tried several troubleshooting steps in an attempt to resolve the issue, but the problem persists. This problem can also occur if the printer drivers are corrupt.

  Refer to the following and see if it helps:

  Step 1: Unplug the printer from the computer.

  Step 2: Connect the printer, uninstall the software from the printer to the computer and reinstall.

  For help to uninstall the application, refer to the suggestions for the following link.

  http://Windows.Microsoft.com/en-us/Windows/uninstall-change-program

  To download and install the drivers, see the following link.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=5286643&

  I hope this helps. If you need help with Windows, let us know and will be happy to help you.

• Printer error state

  I recently bought a computer from windows 8. I downloaded new driver for my PSC 750 successfully, but every time I have try nto print anything, I get a message on my computer that says PRINTER IS in STATE of ERROR. I have no idea what that means or what I need to do to solve this problem, can someone helpme please?

  Thanks for this - it seems like I'm a total jerk - the * bleep * thing was not connected.

  The USB was out when I moved the computer to the back of my desk!

  DOH!

• LaserJet 4000 TN: The printer HP Laserjet 4000 Series PCL5: error state & quot; message & quot;

  I sent the following message to Microsoft after a ' update:

  I have a printer HP Laserjet 4000 Series PCL5 TN which worked beautifully "black only" for many years. A recent update (Windows 10:12 / 22/15) seemed to put the printer in the "printer error state", when you try to print a simple document. It has been my default printer for a long time. I followed the suggestions of printer "windows 10", that is, unplug and plug - check cable (not USB) connections, remove the printer from the list of print devices /, reinstall drivers HP for Windows 10 (following suggestions from HP on HP site) - nothing seems to work. It has a network cable connection, but it is directly connected to my computer, no other computers are connected. See screen capture below. I even did a "recovery" of before 12/22! Any suggestions? Thank you. GM

  I received instructions from Microsoft:

  You run the printer Troubleshooter and identify the cause?

  If this isn't the case, we will do that by visiting the link below and see if it helps.

  http://Windows.Microsoft.com/en-us/Windows-10/fix-printer-problems

  Check also the update (KB number) has recently been installed on your computer.

  You can also restore printer drivers and check.

  To restore the driver, you can follow the steps below:

  • Press Windows + R on the desktop screen.
  • Type devmgmt.msc and press ENTER.
  • Expand the printer drivers and do a right-click on the driver and select Properties.
  • Go to the driver tab and click driver RollBack.

  Can I assume that you use a parallel cable to connect the printer to the computer.  If you do this is a known problem that can be solved.  Go to Device Manager and then click ports.  Double-click the lpt for the printer port, and then click on device settings at the top.  Change the default setting of the middle box checked in the box below to use any available interruption. I would also check the legacy down.  If necessary, turn the computer off and then turn it back on, but most of the time this solves the problem without a reboot.

• HP Officejet 5740: Msg 'printer is in an error state.

  Hello

  I have a 5740 which is defined as a remote wireless printer by itself in my home network.

  Recently, I received the message 'printer is in an error state' when I press print and found out the print job will be lance automatically, only after I turned the printer off and restarted. What happened several times. I tried to use HP & Doc Scan printing, but this did not help.

  Appreciate your advice on the following points: -.

  1. What is the cause for this?

  2. connecting the printer via the USB port on my HP All in one PC would help eliminate this recurring issue?

  3. If Yes, should I uninstall the printer software first?

  4. always print wireless from my laptop or mobile devices when the printer is connected via a cable to my PC?

  What do I have to uninstall and reinstall the software for printing these devices as well?

  5. when I reinstalled the software, it come a last step where it will ask me to register so far HP ink. As I have already registered for the program, what should I do to allow me to complete the installation of the software without duplicating a new series of HP ink instant registration?

  Thank you.

  Hi @Chrissy_61,

  Thanks for joining the Forums of HP Support for a solution to your printer problem.

  I understand that you use a HP Officejet 5740 e-all-in-one printer with a Windows 10 computer and you need to restart the printer to clear a State of 'error', so the printer will print. I would like to help with that.

  There are also a few different reasons why something like this can happen. It could possibly be network or firewall related, or maybe even related software.

  I would like to begin by downloading and running the tool HP Print and Scan Doctor to check the installed printer software. This tool can diagnose and solve many problems of printing software and printer.

  You can also check to make sure that the printer firmware is up-to-date. On the Control Panel Home screen controle control printer, drag your finger from right to left on the screen and select Setup. In the menu select Maintenance of the printerconfiguration, and then select update of the printer, and then look for the updates of the printer.

  If the printer doesn't have the printing problem with PC and not with cell phones and mobile devices, you can try following the steps described in this document of support - printer is offline (Windows).

  If you plan to use a USB between PC and the printer connection, you do not need to uninstall the software, you just remove the printer devices and printers on the computer and connect the USB cable.

  You can always the printer wirelessly with other devices if you have a computer with a USB cable.

  Finally, you need not re-register with the HP Instant ink. You can close the windows when they open after you have installed the software.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• hp8600 message printer in State of the error on some files, print other files.

  Cannot print a couple of files that are both through the cloud, and at least it is in PDF format. message bed printer in an error state.

  Can print out of web sites.

  Hi @Joe819,

  Welcome to the Forums of HP's Support.  I understand that some of your files are not using your printer Officejet 8600 when using cloud printing solutions.

  To help you, you please provide additional information?

  • How is your printer connected (USB cable, ethernet or wireless)?
  • Using HP ePrint, Google Cloud Print or another method?
  • If you are using HP ePrint, print history indicates jobs failed? Discover the story printed in connected HP
  • Were any document that was not able to print, you able to print directly from your computer to the printer without using the method of cloud?
  • All work failed comes a device?  If Yes, what is the operating system of the device?  whatsmyos.com

  Thank you and I look forward to your responses.

• HP Envy 7645 All in One Printe: HP envy 7645printer in an error state

  Do not print, error message saying printer is in an error state.  My wireless network Test results came back all good.  How to fix the error state and what it means?

  Welcome to the HP Forums @cijbj,

  I saw your post on your desire 7645 being in a "State of the error" and not printing on Windows 10 and wanted to tender hand to try to help you. I have a few suggestions to start with and would try you them and let me know the results when you're done.

  1 be able to reset the printer:

  • Turn on the printer.
    With the printer, unplug the power cord at the back of the unit.
    Unplug the power cord from the wall outlet.
    Wait at least 15 seconds.
    Plug the power cord into the wall outlet.
    Reconnect the power cord to the back of the unit.
    If the printer does not by itself, press the Power button to turn it on.
  • Tip: make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on.

  2. try to make copies of the printer, If the copies are working properly, proceed to step 3.

  3. run the print and scan the doctor. This diagnostic tool will check for all conflicts that may be causing the problem. The tool will show you a report at the end. If there is a problem that the tool could not fix, you will notice it in the results. Please send me these results.

  4. try printing and scanning.

  If the copies do not work, please consider contacting HP to see them order a replacement for you printer printers warranty.

  Details of HP:

  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number are displayed.

  I hope this helps you and guide you in the right direction!

  Testify of my answer today by clicking on the thumbs to the top of the icon at the bottom of this post!

• HP Officejet Pro 6830: Get the printer and the message "the printer into an error state" will not be printed

  Just received this printer refurbished HP 2 weeks ago to replace the one who had a problem with printhead.  Printing worked initially, but now I get the message "the printer into an error state" when I try to print.  The screen at the front of the printer automatically turns off as well, as he is extinguished.

  Hi @M45,

  Thank you for joining the Forums of HP Support!

  I see that you are unable to print because the printer is in an error state. I will definitely do my best to help you and don't forget to come back to this thread and mark "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to do a hard reset to see if that will solve the problem.

  1. Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  2. Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
  3. Make sure that the printer is connected directly to a wall outlet (do not use a bar or a surge protector).

  If there's an error message displayed in the menu on the front panel, before the display of the printer turns off?

  Please download and run the print and Scan of the doctor, it will be probably diagnose and fix the problem you are experiencing.

  • What were the results when you ran the printing and scanning doctor (she print or scan, error messages)?
  • Click here to update the firmware of the printer with a USB connection.

  If you have completed all the above steps and your product still has a problem, service the product.

  Check the warranty status: http://h20564.www2.hp.com/hpsc/wc/public/home
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: http://support.hp.com/us-en/contact-hp
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  I hope this helps. Please respond if you have any questions. I wish you a nice day!

• HP Deskjet 3051 a model J611H: printer is in an error state

  For months after a cross-country skiing, I couldn't set up the function wireless on my printer (he had already worked with no problem). After a factory reset my router yesterday, it is finally connected to my home network. I tried to print a test page to make sure that everything worked properly and I got the following message on my computer:

  "The printer is in an error state. Please solve the error of the device and try again. »

  There is no error message on the screen of the printer itself, however. The menu normal forms of copy/scanning/quick is in place. The printer menus say he is connected to the network and gives me the IP address to which it is connected. I was able to print the 'printer status report"directly from the printer, so I know that it can print at least somehow.

  Is it possible to fix this?

  Hello

  You can see any difference using Jetdirect instead of Hello?

  Second step: print a Network Configuration Page