My laptop shows "no internet access", but it is connected

Similar Questions

• My network connection shows no internet access, but I can access the internet

  Hardware: Dell XPS 8300

  OS: Windows 7 family

  System type: 64-Bit
  In the network and sharing Center, it is show the connection between the network of Multi and the Internet has an 'X', but I have full internet access.
  Is there a way to fix this?

  Hello

  I understand that you are able to connect to the internet when your computer showing no network connection.

  1. did you of recent changes to the computer?

  I would suggest trying the following instructions and check if it helps.

  Method 1: update the network driver.

  Steps to update of network driver:

  1. click on the Start button.
  2. in the search box type devmgmt.msc, and then press ENTER.
  3. Select the network card device and right click on it
  4. now, select Properties.
  5. in the Properties window, on the driver tab, click Update driver.
  6. After installing the updates, restart the computer.

  For more information visit: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  Method 2:

  Temporarily disable the Antivirus and firewall

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Network icon shows no internet access, even if I am connected to the Internet

  I have a dell inspiron 15 r 5521 with windows 8 os (c) Microsoft Corporation 2012.

  In our college after joining the network local network we must go to the website of the computer center and connect through his id and password. After that only we have access to the internet. But even after access the internet icon shows without internet access. I can't use my apps windows for this reason. In the windows of another 8.1, it shows internet access.

  Hi Naman,

  1. Do you have an error message when you try to connect to the Internet?
  2. Are you able to connect to other networks?
  3. Did you recent hardware or changes to the software to the computer before the show?

  I suggest you contact the administrator of system network College if the problem only occurs when you try to connect to the College network.

  You can also publish the application on the TechNet forums if the computer is connected to the domain.

  http://social.technet.Microsoft.com/forums/en-us/category/w8itpro

  You can refer to the suggestion that I have provided from the link next if you are unable to connect to any network.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-networking/unable-to-connect-to-Internet-in-Windows-8/675d0f63-DCC1-436C-b49a-9863c22caa4c

  I hope this helps.

  Please report if the problem persists and we will be happy to help you further.

• Windows 7 connects and says "Internet access", but cannot access the internet!

  Hello, please help me with this annoying problem in answering it.

  My PC connects successfully to the mobile hotspot and indicates that he gined Internet access, but when I try to browse the internet (I tried Google Chrome, Internet Explorer, and Mozilla Firefox), or use any application that needs to connect to the internet (such as online games) HE DO FACT NOT WORKING, or SAY "NOT CONNECTED to the INTERNET.

  In the time that each connected device another works perfectly.

  Please when you view this thread the RESPONSE and not SIMPLY LEAVE.

  Thank you to everyone who helps me.

  Thank you to everyone who helped or tried to help me. It if a virus blocking internet access to applications. I now come back to my PC back working.

• I recently purchaced a Netgear wireless router. I can't get any Internet access every time I connect to the internet.

  I recently purchaced a Netgear wireless router, I can't get any Internet access every time I connect to internet

  Hello

  Your computer connects to other networks wireless?

  Check with the Netgear support, their online documentation, firmware and ask for their
  Communities and Forums.

  NetGear
  http://www.NETGEAR.com/

  NetGear - Support & community
  http://support.NETGEAR.com/app/

  NetGear - Forums
  http://forum1.NETGEAR.com/

  -----------------------------------

  Have you checked the updates or re-installed the driver of your WiFi? Check with the manufacturer of the system (motherboard
  Manufacturer of custom systems) If an edge device and/or the manufacturer of the device.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I downloaded the Adobe digital editions, but I'm not allowed my computer, they say that I should connect to internet first, but I am connected?

  Please help me thanks!

  I downloaded the Adobe digital editions, but I'm not allowed my computer, they say that I should connect to internet first, but I am connected?

  attach a screenshot of the exact error message would be useful, if the link below does not work.

  Log, activation, or connection errors. CS5.5 and later versions

• LAN/Ethernet and wireless: can connect to networks, but shows "no Internet access.

  My workplace has cable/Ethernet and Wi - Fi.  I'm working on a laptop, plug it into a dock where my ethernet cable is connected.  Lately, I've been the startup object and the network will connect automatically (by default to connect to the local network, not for the wireless) but I get the point of the triangle/yellow exclamation on my network icon and displays "no Internet access.  Even if I get this warning message /, in fact, I can access the internet, but I can't access resources online through a program installed (such as, to access to the / insertion of a photo online by word or update a SharePoint Outlook calendar).

  In the past, I could connect wirelessly and work around this problem.  However, now my wireless connection does the same thing: it will connect, it displays the warning "no access Internet, I can access the internet, but not another program."

  I ran the resolution of problems and it does not identify the problem.  I've updated drivers, disconnected and reconnected networks - nothing seems to work.  Any ideas?

  Given that you encounter this work to your work network you really need to get your business COMPUTER Department to come and watch. As far as we know, there may be certain restrictions checked in your network permissions that must not checked. There is so much that can happen it is impossible to diagnose on an online forum.

• Blocked office internet access but not laptop on the same internet connection.

  I ran Malwarebytes software... which is on top of my McAfee... and he finds 6 infections, remove them, rebooted, the internet connects for a few minutes then gets lost.

  Confirmed network connection. Icon indicates a service, but does not connect.

  Hello

  What is the status of the NIC in Device Manager?

  Read the following article that may help you resolve this problem.
  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095

• Enable the VLAN on sub interface internet access but block traffic to VLAN native

  I have a 2821 router w / MLS 2024 switches.  Native VLAN(default vlan) is my private network and VLAN 100 is my comments system.  Below is my interface config...

  interface GigabitEthernet0/1

  Description ES_LAN, ETH - LAN$ $$

  IP 10.1.0.2 255.255.0.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1.1

  encapsulation dot1Q 100

  IP 10.3.1.254 255.255.255.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  !

  IP default-gateway xx.xxx.xxx.xxx

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  Default route is defined...

  IP route 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx

  Access list are...

  access-list 175 deny ip 10.1.0.0 0.0.255.255 10.2.0.0 0.0.255.255

  access-list 175 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 175 deny ip 10.3.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  access-list 175 allow ip 10.3.1.0 0.0.0.255 any

  I want to continue to have access to the guest VLAN in VLAN private to allow the management of points of access etc.

  I want to allow internet access as guest newtork but block it to access my private network.

  Don't know how to do in this regard.  I tried to change the ACLs (remove the 10.3.1.0 entries) and creating an another acl for the Scriptures and applying that VLAN 100 sub interface... so far without success.

  Thanks in advance for the help!

  Hello Chris,

  > From this point of view should I leave the above lines and create another list acl for the 10.3.1.0 of the network and apply entering gig0/1.1?

  I would go this way, as in a simple ACL, you can't express your needs. The ACL to apply on gi0/1.1 will probably need further instructions then the ones I suggested, but divide the problem into smaller manageable pieces is a good strategy.

  > Also with this config would be NAT be performed on each network by making this change?

  Until the internal network and network of comments are on the same side (ip nat inside) there is no NAT triggered in communication between them so that you should not influence the NAT configuration with this change.

  Hope to help

  Giuseppe

• No internet access when you're connected to my wireless router

  I have a laptop Compaq Presario CQ62

  OS: Windows 7 64-bit,

  Processor: AMD V120 processor 2.20 GHz

  Network adapter: Broadcom 4313 802.11b/g/n and Microsoft Virtual WiFi Miniport

  A month ago, I was using internet and then it suddenly stopped working. I am connected to the wireless connection, but there is no Internet access. I tried to leave the network and joining, turn off the router for 5 minutes, but nothing seems to work. What can I do?

  Keiron Wilce

  Thanks for all the help guys, but it seems that my anti-virus just need to update that was made by another computer and do pass through a pen-drive. Once again thank you for all the help.

• No internet access when it is connected to the modem

  HI I have an Ethernet cable modem BEFMCU10 model v3 connected to a Netgear n100 v2 wireless router. The modem works only when it is connected with the wireless router. When I try to connect Ethernet. Modem to PC, it does not connect, there is no internet access. My ISP is Comcast (Xfinity). It's really weird because how is it possible that theres internet via wireless, but when I connect my modem via Ethernet, I have no internet access

  I remember the first time I activated my modem there is xfinity software that did something to my modem but I don't think it has to do with anything he just install something in my laptop. I did a clean install of the software or anything has been removed.

  > Sometimes I download things and I prefer to use the physical connection because its faster.

  You will get the same benefits and an easier time using a wired connection to your router, rather than the modem.

  > My prolem is resolved, I followed your instructions, thank you

  You are welcome. Please mark as replied to close the issue.

  > is - this quite useful to purchase a Docsis 3.0 modem

  You can check this with your cable provider, but probably not.  Unless you have a very high speed (usually of company type) cable plan there would be no advantage.   You also must be sure that any modem you purchase is compatible.

• No Internet access - network/router wireless connection problem

  I can't connect to the internet after installing Windows 7 64 bit. I can see the router wireless/network from my computer, but it has sometimes limited connectivity or it says connected but no internet access. I used Windows diagnostic tools to try to fix it but it does not work, and my router connects without a doubt to the internet such that I now use on a portable computer that is on the same network. I would like to know if anyone else has this problem and if they fixed. I tried to change the physical address of the connection to the local network, but it didn't work, I guess because I connect via radio and no cable, and I heard similar stories on other forums that this can be a problem more common I suspect. Thanks in advance for your answer, and all the details you need I'll try my best to provide.

  OK I finally got to work, all we needed was for me to download the latest drivers (Realtek 8185 wireless card) off-site and install in compatibility mode, and then he worked all of a sudden. I hope this will help someone suffering from a similar problem!

• modem and router work on other computers, but a computer shows no internet access and no IPv6 IPv4 ort connectvitity

  I have access to the modem router / wireless on laptop, IPAD and a PC computer.  However my Windows 7 PC, depicts all of a sudden strong router connection with small exclamation point under power router and NO internet connection. The

  Wierless network login screen says I have no. IPv4 or IPv6 connectivity. I tried to reset winsock and IP nothing helps. Can't do on the internet, when well even the modem and the router are OK

  I have access to the modem router / wireless on laptop, IPAD and a PC computer.  However my Windows 7 PC, depicts all of a sudden strong router connection with small exclamation point under power router and NO internet connection. The

  Wierless network login screen says I have no. IPv4 or IPv6 connectivity. I tried to reset winsock and IP nothing helps. Can't do on the internet, when well even the modem and the router are OK

  Try this:

  1. Open network connections by clicking the start , and then clicking Control Panel. In the search box, type adapter and then, under center network and sharing, click view network connections.

  2. Right click on the connection that you want to change, and then click Properties. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. Click the network tab. Under this connection uses the following items, click Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), and then click Properties.

  Double check and make sure obtain DNS / IP are both checked on automatic.

• After the death of firewall router in an outtage power yesterday I replaced my router have restored internet access, but none of my corporate office offices can access our network printer/scanner.

  yerterday morning, that we had a power outage at my place of business. When power has been restored we can't access internet from any one of our desktop computers. After working with a material MFG co troubleshotter. our firewall router NETGEAR, it has been determined that the equipment was defective. They offered to replace the camera for only the shipping charges, I felt an acceptable solution. Then I was told that with bureaucracy, it would take two weeks to get the new unit. Well, my choice was then to set for two weeks and slowly go out of business or buying a new router. I have relpaced the unit with another mod. Netgear router and this quickly got back up again, at least if we could access our system of internal accounting and the internet. My problem is as it is now that I can't access our office network printer.scanner (kyoceraMita) of any one of my desktops. At this point, I'd appreciate any help. I own my business, but am not a computer guy of any measurment known to man. I have this idea, maybe it's a simple software for all fit everyone access to what they need, but I don't know what it is maybe. If sufficient information, in my view, that I could probably fix the problem myself without providing any benefits of outdoor programming.

  The problem now is that the router has changed, the addresses IP, subnet mask, default gateway address, network security wireless network wireless security password and other settings no longer correspond to the original router.  As you said that the SCP can all see each other, you need to see Kyocera and network user's guide 'unit' in order to find the IP address, subnet mask and other network setting the configuration parameters 'method '.

• WRTP54G router: I have wireless internet access, but is not a wired desktop computer.

  We have a great wireless network in the home, but my office (which is not wireless) is unable to access the internet.  It is said that a network cable is unplugged - it isn't.  When a cable is plugged into one of the 4 ports on the back of the router ethernet, ethernet LEDs located on the front doesn't light up or blink or anything.  I think that the part does not work.  Is there something I can do?  Should I update the firmware?  Or just get a new router?  I tried different cables, but nothing changes.  The only way for the office get online is to take the router configuration, but then the wireless network and the Vonage phone came out.

  I went to ipconfig at the prompt of commands and under the Ethernet connection to the Local network card: my media is media disconnected.  So, I'm guessing that the router's ethernet ports do not work.

  Thanks for your help.

  Make the continuos ping ping 192.168.1.1 t and check how many answers or RTO you will. If you still have some of the answers, connect your PC to the modem to get internet connection and download the latest firmware and utility upgrade for your router.

  FIRMWARE

  1. go to www.linksys.com/downloads

  2. Enter the model number of your router

  3. choose Get downloads

  4. Select the Version of the device

  5. check drivers and downloads, can download the Firmware

  UPGRADE UTILITY

  1. go to www.linksys.com/downloads

  2. Enter the model is BEFSR41

  3. choose Get downloads

  4. Select the Version of the device - Version 4.0

  5. check drivers and downloads, can download the utility

  After downloading these files.

  Connect your PC to the router, and then run the TFTP (Utlity) set Server = 192.168.1.1; Password = admin; then choose the firmware file that you downloaded. Then upgrade the firmware of your router.

  Note: Make sure that you set TCP/IP and DNS server you computer back to GET the IP ADDRESS.

  Note: To run the utility TFTP set TCP/IP and DNS server on your computer to USE THE FOLLOWING IP ADDREESS.

  Just follow the previous posts to do this. Good luck.