my router wireless guard Plug and go offline.unplug and it works again

Similar Questions

• My internet connection is lost at home after a few minutes. I re - turn on the wifi disabled, ten and it works again for a few minutes and then repeats. It works fine everywhere else?

  Relatively new MacBook OSX El Cap 11.4

  My internet connection is lost at home after a few minutes. I stop the wifi, then turn it back on and it works again for a few minutes and then repeats. It works fine everywhere else?

  Please see recommended settings of WiFi routers and access Apple points.

  Despite these recommendations, some routers will work better with the latest Mac models if you turn the radio 2.4 GHz mode in settings and only use the 5 GHz. Note, however, that very old devices Apple and some third-party devices can then not connect at all.

  Some third party routers have advanced that you may need to change the settings:

  The encryption algorithm must be AES.

  The group key interval must be 3200.

  I can't give you specific instructions on how to change these settings, because all routers are different. Refer to the documentation for the provider.

• How can I remove the wireless network settings and the Working Group?

  I used the Setup Wizard to establish them, and now I want to remove them completely.  I use Windows XP SP3.

  Hi 13emily,

  Try the step below to remove the connection to the computer's wireless network.

  (a) click Start, click Control Panel, and then click network connections.

  (b) right click on wireless network connection and then click Remove.

  To remove a network component

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/howto_remove_component.mspx?mfr=true

  When you set up a network, Windows automatically creates a workgroup and gives it a name. As we cannot delete a task force but if you rename the working group which will remove access to other computers.

  To rename a computer

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sysdm_ident_change_computer_name.mspx?mfr=true

• my wireless turn ON and OFF periodically again and again in T41

  Hello

  I use T41, winxp, when I turn on my wireless, it connects and after some time even once connect it means disconnection occurs periodically again and again.  '2100 3B card' is installed I think

  ON, OFF, ON, OFF wireless

  = excellent signal strength

  Yes, in my case I put it channel 6,

  • defining the energy needs for Maximum performance on all options
  • in going "BIOS setup Utility" to-> (changing from Auto to Maximiz)
  • Maximum etc. CPU power management

  fixed my problem, until the fact T41 now not disconnected itself. for 3 hours.

  My card is «...» 2100 3 b..., ' it means that it supports 802.11 a, b.

  for this the security settings in the AP should me done now settings are WEP?

  the next thing is that when the security level is none in AP, Access Point (TP-LINK (TL-WA501G)). My T41 works smoothly without any ON, OFF or connect, disconnect.

• Internet constantly stops working, says "WiFi is not a valid ip configuration" and then working again shortly.

  The problem
  I continue to have this problem where my internet no longer works, I always run a diagnosis "fail" (or whatever it is called in English) and he told me that wifi is not a valid ip address configuration and then the internet works again. This can happen several times daily. I think this could be a problem between this PC and the router because the other PC in this Chamber works very well on the internet. My PC works great too when I am connected to other internet connections.
  Solutions
  I tried the fix: open commandprom, type netsh winsock reset catalog, and then type netsh int ip reset reset.log hit.
  I tried the fix: open commandpromt, type ipconfig / renew.
  Info
  PC is a MSI GE60 (i5, GTX 660 m)
  Intel Wireless Driver

  They are models of multiple GE60, each model is supplied with 2 different wireless drivers and I can't know that you have your computer

  AzureWave: http://www.msi.com/service/download/nbdriver-21557.html
  Intel: http://www.msi.com/service/download/nbdriver-21013.html
  You can try both of them, will not bad cause install one incorrect

• T410 slow system in the bios post and towers works again on restart

  I met this system when it came to upgrade Windows XP to win7 for my business.

  We want to have the same version of the bios on all systems, and this one had an outdated bios, so I did an upgrade to 1.35.

  To complete the upgrade, you must press ENTER to reboot the system. It took about 30 sek for the system to reboot after I pressed Enter. It was the first clue that the system acted weird. After the bios update, I noticed that when a reboot is initiated by the operating system, the laptop shuts down for 10 sek and then on again. Then fire Power On password. Normally, there are no POP when you restart.

  I tried upgrading the bios version 1.36 but no change.

  This problem has been fixed. BIOS has been reset by removing the mb battery and reconfigured.

• My wireless HP D110 printer is offline. How to print again? cc = us

  I have windows XP and my husband has Vista.  Message from the printer, it is in offline mode.  I can't find how to reset the printer.  It is the HP Photosmart D110 series.  Thank you

  Hi MonicaDB,

  HP has designed a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity: The HP Print and Scan doctor. HP recommend you to download and install Print and scan doctor no matter what time you need to solve a problem with your HP printer from the link below.

  I would like to know what are the errors you receive?

  http://www.HP.com/go/tools

• Modem router Wireless N upgrade?

  I have a Linksys BEFCMU10 ver.2 modem which has served us for about 8 years.  I've recently updated our wireless n router, but have seen no improvement in the coverage area or speed.  The seller in Microcenter told me that my current modem was fine, but I wonder if I need to improve my modem to take advantage of the N WiFi feature.  Another thing, I remember when the tech our cable connected to the modem, it added a 10/100 switch.  Can it be purchased?  The research I did on the forums, it seems that I need a compatible 10/100/1000 switch for the gigabit speed.

  I apologize for the basic questions, but I tell myself that if I want to learn I have well start somewhere

  Thank you!

  It is not question of cause I don't think you have 100Mpbs subscription from your ISP. This modem is good for home use. You will get your your router Wireless N speed and that's only within your local network.

• Satellite L455 - plug-and - battery LEDs power LED and it flashes orange

  I have a Satellite L455, which worked perfectly for more than six months now, but two weeks ago he began to behave strangely.

  I turned off the machine normally in the evening I was going to sleep. In the morning when I turned on it it turned on, HARD drive and on power LED blinked blue for a few seconds then they are gone. Machine does not start. I tried to turn it on again and it does the same thing. Then I saw the "power plug on" and "battery on" LED flashes orange at the same time. I unplugged the power adapter. Both lights were continuous blinking but machine will not feed. I removed the battery for a piece of 5 minutes, then reinserted it and the machine has worked all day.

  I went he deleted off the power plug and the morning again it wouldn't start until the when I removed the battery for a few minutes then it works again. The battery recharges very well that when I remove and reinsert it even without connecting the power cable still lights up and works perfectly.

  Then, I removed the battery and the power supply Plug and you press the power button for 30 seconds to unload the machine and then return power and battery and it worked until I turned off again and shutting off the power and then it didn't once again.

  If I stop just of machine and do not turn off the power cord, then I can turn it back on to and work with the machine without hassle even for three days without interruption.

  What could be wrong? Any help will be really appreciated.

  Concerning
  Yusuf

  Hi chidzungo,

  It must certainly be a hardware malfunction but he s strange why it pops up every day after you have closed the laptop. Do you use batteries and AC/DC to original Toshiba adapter? Have you connected external devices to your laptop? If so delete them before you turn on your laptop.

  What version of BIOS is installed at the moment? You should look on the Web from Toshiba website for an update. Update of the BIOS might also help and it s worth a try.

  Before you start reading the BIOS BIOS update instructions update [HERE: http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=60]

  Satellite L455 seems to be an American model, so the BIOS update can be downloaded from the Toshiba U.S. page but first check the exact part number:
  http://www.CSD.Toshiba.com/

• My Bluetooth Mobile Keyboard 5000 stagnates and stops working intermittently

  I have a Microsoft Bluetooth Mobile Keyboard 5000 running 64-bit Windows 7 Pro SP1. When it works, it's great, and I like the compact design and wireless. But in the last few months, I noticed a few problems which become quite annoying:

  1. When I'm editing, the keyboard seems often slow to react. For example, I often use combinations of keys such as Ctrl + C or Ctrl + X, and it's as if the keyboard does not have the CTRL key immediately, so I find myself by typing 'C' or 'X' on my choice. If I click Cancel and try again, it usually works after that. Or I'll click on an input field and start typing and it takes 1 to 3 seconds for the text to appear, but it usually everything happens, is not as if the keyboard is in decline in strikes, but just a delay. It's almost like the keyboard has a period of awakening to send data. It doesn't seem to be a way to control or override this behavior. And we don't mean to be away from the keyboard for hours or anything like that; Instead, it's time to switch between windows.
  2. At least once a day, just a keyboard unresponsive altogether. When this happens, I can go into my Bluetooth settings, remove the device, press the Connect button on the back of the keyboard to set pairing mode again (or usually it comes automatically drops back in pairing mode when I delete) and then plug it in again. He sails right through matching and starts working again... until the next time it stops. There seems not to be a lot of consistency to when this happens, but this is often when my boss stops by my office and asked me to show him something. Needless to say, not the best time for the elegant Bluetooth keyboard go toots upward.

  The keyboard said it was MFG. 12/11, is less than 1 year old. Do I need better drivers? Can anyone recommend a troubleshooting step I've overlooked? The keyboard is damaged? I can send it to Microsoft for repair or diagnosis? Do I use? Thanks for any advice you can offer.

  Hello

  -You are aware of any changes made on the computer before this problem?
  -You are faced with the question while working on a certain application (like Microsoft Word) or the licensing is pure coincidence?
   
  Method 1: Run the Troubleshooting Utility from the link below and check if the problem persists.
  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter
   
  Method 2: I suggest you to see link below and check if it helps.
  Troubleshooting Wireless and Bluetooth problems
  http://www.Microsoft.com/hardware/en-us/help/support/troubleshooting/keyboard/wireless-Bluetooth
  Also, I suggest you to contact Microsoft Hardware Support for better support.
  http://www.Microsoft.com/hardware/en-us/support
   
  Hope this information helps.

• Printer not responding not connections (wireless printer) is good and solid. I replaced my old router wirelessly with a router of valuation. I had to plug it, but the printer does not respond now.

  Printer not responding not connections (wireless printer) is good and solid. I replaced my old router wirelessly with a router of valuation.  I had to plug it, but the printer does not respond now.

  Is what brand and model of printer?

  I do not work unless your new router has the same SSID and password wireless as the old. Consult your printer documentation to find out how to handle the situation. For example, some Lexmark wireless printers have a program called Configuration Utility Wireless in the Lexmark folder under all programs on the start menu that is used to set up the printer when changes are made to the wireless network.

• OfficeJet 6500 and router Wireless does not connect

  I just bought an Officejet 6500 and try to connect to my wireless router.  Whenever I try to connect the printer to wireless it crashes.  The power button does not light, but the screen is lit without text.  At this point, I can't close or get it running again.  I am running Vista Business 64-bit, and the router is a 2wire 1800 HG through AT & T.  It works very well with a usb connection.

  Thanks in advance.  John

  I think you just meet a known issue with some printers of HP network with routers 2WIRE AT & T DSL.

  Have identified us the problem and will deploy an update in the future.  So far, the work around is to assign a static IP address to the printer. Here's a way to do this:

  1. Unplug the phone line from the 2WIRE router
  2. Cut the power to the 2WIRE router, wait 30 seconds, then turn on the power.
  3. Go through the normal process of the printer connected to the 2WIRE (Ethernet or Wi - Fi) device. The printer will not crash as long as the telephone line is disconnected from the 2WIRE device.
  4. The Officejet front panel, go to the menu of 'Advanced Setup' under 'network '.
  5. Select 'Settings of intellectual property', acknowledge receipt of the warning and select "" manual IP ".
  6. Select "IP address" and change the last group of IPS (byte) to something higher or lower. Specifically to your 2WIRE router, select 192.168.0.60.
  7. Press Ok and plug the phone line into the 2WIRE router.
   

• Kodak ESPC310 + 0365 and Sony Vaio both on the same wireless network, Vaio says printer offline, so don't not printing - suggestions?

  Kodak ESPC310 + 0365 and Sony Vaio, printing problem

  Kodak ESPC310 + 0365 and Sony Vaio both on the same wireless network, Vaio says printer offline, so don't not printing - suggestions?

  Hello

  ·         What operating system do you use?

  ·         Remember to proceed with changes in hardware or software on the computer before the show?

  Follow these methods and check if that helps:

  Method 1:

  I suggest you run the fixit tool and check if it helps.

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/

  Method 2:

  Follow the steps in troubleshooting section and check if that helps.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  See also:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

   

  http://support.en.kodak.com/app/answers/detail/A_ID/19500/selected/true

   

  http://support.en.kodak.com/app/answers/detail/A_ID/1329/selected/true

• Follow-up of the steps to install the hp wireless printer and it worked only once. Now he says it is "offline."

  Original title: the computer geek

  Follow-up of the steps to install the hp wireless printer and it worked only once. Now he says it is "offline." Convenience store said that it cannot solve the problem. That's happened?

  Hello

  1. What is the brand and model of the printer?
  2. don't you make changes on the computer recently before this problem?
  3. What is the full and exact error message?

  Step 1: The procedure below can help you to fix this problem.

  a. Click Start > Control Panel > printer and faxes
  b. now right-click on computer and select the printer to use online

  Step 2: Update printer drivers.

  To install new or updated printer drivers to update
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/print_drivers_install_updatew.mspx?mfr=true

• When I try to connect to my router wirelessly from my laptop and the room, he asks for my network key and I don't know what it is.

  my brother used to all our computer equipment set up and he died last year. Well when I moved and tried to get into my new place it will not allow me without a network/wpa key. I know that I am trying to connect to my router and not my neighbors because when I unplug it it's the only name that disappears from the list of wireless networks. How can I know what is the network key or even set up a new? I am a bit technologically with faculties weakened to get detailed instructions on how to help me would be appreciated, but any help would be great.

  I'm sorry for your loss. Since we do not know how your brother to set up the router, it would be better to start again just to make sure that your wireless network is secure. Reset the default router. This is usually done with the wired router (on) by pressing a small button on the back or the bottom of the router, now the button for about 30 seconds and then let go. You can find the manual on the router mftr's Web site. your router if you need it.

  Once you have reset the router to default, set up correctly:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing. MS - MVP - Elephant Boy computers - don't panic!