NAT9914 - direct connection to the GPIB bus

Similar Questions

• Internet does not connect unless it is directly connected to the computer

  This problem occurred yesterday.

  Internet has suddenly stopped working. Things were going to turn power off, then on and distributed. I did check the lights on the modem and the router, but they were all working well. I have plugged on both computers. This does not solve it. I called Charter to see if there was a failure. Unfortunately, it's a message auto troubleshooting which I have materialized with. He had me hang my modem directly to my computer. This solved my problems of the internet.

  I went to sleep for the night in the hope that the internet, or what the question was, would fix itself. He did not. The internet still works only if it is directly connected to the computer.

  There are other people who need to use the internet here. (Invoices, work schedules and other) So maybe it's very much a problem. Any other computer or phone, will work in the House.

  What is a router problem or a cable, or...?

  If your connection works when you plug the modem but not through the router, this indicates a problem with the router.   This could be a hardware failure or a configuration problem.  A problem with the cable between the modem and the WAN port on the router is possible, but unlikely.  It wouldn't hurt to check if she.  Most routers have a reset button recessed.  I suggest that you reset the router and reinstall as if new.  If this fails, you probably need to replace the router.

  Depending on your technical knowledge, you can also log in to the router and check the status information.

• to reach a server on a VLAN that is not directly connected to the inside interface

  scénarion

  PIX 515

  6506 core with VLAN A, B, c. (intervlan routing is ok)

  vlanC is directly connected to the inside interface of the fw

  question

  How a crowd outside could reach a server ServerA on vlanA.

  Hello

  Concerning Point 1, Yes if the roads required for networks connected inside the network is done on pix.

  Concerning Point 2, if the IP address that you use within the network is routable (public IP), the command you gave will work. The command indicates that when 10.10.1.10 inside the network host wants to go outside the network, use the same IP address. Because NAT does not occur, the actual address of the server presents itself as the visible address and the address of the host. So if the IP address you specify is not a public IP address, outside world can't access.

• Direct connection to the view Agent Linux?

  Is there an implementation linux plugin for direct connection from the view of the PicoIP client (I use VMware View on Mac) on a Linux desktop?

  I just wanted to put in place a set of virtual machines Linux to be accessible by customers to view, Mac. Also intend to do not use a view connection server. I installed a virtual machine to test with Ubuntu top end and configure the Agent as well.

  Direct connection is not supported. You must configure a login server in your environment.

• "Direct connection to the desktop" and external clients

  Hi all

  I'm doing a View 4 u1 installation with a connection to the server and a security server. I just want to confirm with the setting to view administrator, check box "direct connection on the desktop.

  I find that if I check it, then external clients of internet do not work - can see the office pools, but at launch, the customer will see appear in the taskbar, disappear. When I uncheck, all external clients work very well.

  my understanding is that this check box determines whether RDP traffic will be dug by the connection to the server or it will go straigh from the clients to view offices. I though that this setting affects only internal clients. I don't see how it affects external clients that connect through the Security server.

  When you look at 'netstat' of external clients, trying to run the office, I can see the threshold to appear when the customer view disappears, it will also disappear. Looks like when the box is check (direct connection), the client view external attempts to establish the RDP directly on desktop computers, apparently, it won't work. So, how can a direct connection for internal clients only?

  TCP 192.168.20.2:56473 winxp - 04:ms - wbt-Server SYN_SENT

  any ideas?

  Thank you

  Ming

  In our environment, we have our external users (Security Server) use a broker who has direct connect disabled while internal users use a different set of brokers that are defined to use direct connect.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Drivers to be used on networked computers that are not directly connected to the HP Laserjet M1536dnf MFP

  Hi, I had problems connecting to computers on the network for printer. The printer is HP LaserJet Pro M1536dnf MFP. The computer that is connected to the printer directly via USB is fine. I downloaded solution complete driver installation on the site of hp, them and everything's fine. the problem is with the computers on the network, they cannot detect even the computer to add printer. And I have enabled file sharing and printer sharing advanced options of sharing on all computers. I also tried to install the same drivers I used on the local computer on the network computers, but its does not work. Please kindly advise me on which particular driver should I use or the solution.

  for this one, there was a simple solution... I forgot one small thing. After the installation of the complete solution from hp printer drivers on the computer connected to the printer via the usb port you then go to control panel > view devices and printers > click with the right button on active printer installed > printer properties > sharing > click on the list to the Director. that allows other computers on the network to view the printers.  was a bit stupid coz the solution was so simple.

• HP Officejet Pro 8610: printer directly connected to the Internet

  I'm trying to register for the HP ink cartridges.  The application calls a code to write on request.  However, the printer tells me that Web services are not enabled on my printer.  How can I connect a printer directly to the Internet.  I use a USB cable to connect the printer to my laptop.  Can someone help me so that I can complete the application of the ink?  Thank you!

  mcbrighde

  Hello @mcbrighde,

  Welcome to the Forums of HP's Support. I understand you are trying to join the instant ink program, but need assistance in obtaining your printers code request. I would like to help.

  In order to get the printers claim code, you will need to have the printer on a wireless network. An ethernet or LAN connection will also work. This will give the internet access to the printer so that the ink levels can be monitored.

  You need not remove your USB connection for the printer on the wireless network.

  The following link will help put your Officejet Pro 8600 on the wireless network.

  HP OfficeJet printers - printer wireless (Windows) installation

  Once the printer on the network, tap the icon of ePrint/Web Services to enable Web Services and acquire the printers claim code. The icon you are looking for is in the lower left corner of the screen printers.

  

  You can also use the following link to view more detailed instructions.

  HP - service and using HP ePrint printers

  If you need further assistance or have any other questions please let me know.

  I'll be happy to help you.

• Discover device directly connected to the cisco ASA

  How do I know which is directly connected to an ASA interface? I'm looking for some commands that can be executed on the SAA to find the directly connected Cisco device.

  Thank you

  Boudou

  Unfortunately it is not available on SAA for you tell what device is directly connected to it, there is no 'see the neighboring cdp' on SAA unfortunately.

  You can check the ARP table and see which is the next hop, but who would only give the layer 3 device, such that there could be a switch between the two institutions.

• View internal, external direct connection in the tunnel?

  Today we use XP virtual machines with view 4.0.1 only internal direct connect (need this to our Sun's rays). But now, we want to use our XP virtual machines to internal direct connect and externally by tunnel via the SSL protocol. What do we have to do for that?

  My idea is to install a server security in the demilitarized zone and a new second login view without direct connect server, is the right way?

  If so, we can allow the same VM XP for internal and external direct connection in tunnel?

  That's how we have our configuration of the environment.  You can configure the type of connection to the server by going to the page view Admin, configuration, servers.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Direct connection on the desktop - clients still losing access when the server goes down or rebooted service

  I set up the connection to the server with a link Direct is TICKING, I did that once the initial connection has been made for the broker and an assigned desktop computer, connect directly to the desktop and so not care about the State of the connection to the server. After restart or just restart the VMware View Server service all customers lost access until it is facing up.

  Is it right, that we use View 3.1.

  Thank you

  It's strange that I can restart my server connection without worrying about all the users.   How brokers connection you have and do you have activated all at direct connection?

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Where is the check box "Direct connection" to the pool passed in View 4

  Hi all

  I don't seem to be able to find the box of "Direct connection" who was there on view 3, in order to allow desktop computers once they have made the initial connection to the broker, for you to connect directly to the office. This has been deleted?

  I can see the "direct connection to workstations in offline mode" which is a global setting, but not one for standard pools.

  Any help / pointers greatly appreciated.

  Thank you

  Dan

  No, it has not been deleted.  It is available on a per server in the configuration on the screen from view admin tab basis.  Once in a configuration just click on servers, select the server you want to change the direct connect and change this server.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• "Connection to the GPIB driver or device error".

  Hi all

  It is the first assignment, I do on this forum, so please be refrain, if I make mistakes.

  Now my problem:

  I use the NI USB2GPIB adapter and want to communicate with any GPIB device using the Simple screw GPIB.vi NOR-example.

  From the VI the GPIB - correct the device address occurs an error:

  

  My settings of the GPIB adapter are:

  

  Anyone can unmask, why in MAX, the communication is running:

  

  but not in VI. In the VI I get error indicator, when I try to use the function write GPIB (error bit 15 is set to 1).

  Can someone help me please?

  Sincere best wishes from good old Germany,

  z

  
  

• Installation of Windows 7 Ultimate English SP1 with the German language without direct connection to the internet package

  I need to install Windows 7 Ultimate SP1 (in English) on a server without being able to connect to the server to the Internet.

  Is it possible to download the complete software to install the server without an Internet connection?

  I was looking for a possibility to download, but have not found.

  Stefan

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

• have 2 laptops, HP & Gateway, network, Comcast, completely wireless HP must use direct connect to the router? What has happened, how to fix.

  have a Comcast wireless connection. 2 laptop HP & Gateway, HP, leaving work wireless, must connect directly with a wire to the router, what happened? How to fix? Colleen

  Hi ColleenMiller,

  1. you receive messages or error codes when you connect?

  2 Windows operating system you are using?

  You can view the following items and see if it helps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• Juniper Netscreen SSG20 is directly connected to the Cisco PIX 525.

  Hi all, I have a third-party provider to put a Juniper SSG20 VPN device in our network. I want to connect directly to a PIX 525. Someone at - he tried the same thing? Any question, should I be careful?

  I have attached a diagram of the proposed provision.

  Thank you.

  Dmitry

  Should not be a problem as long as you know what protocol and ports Juniper use so you can open it on the PIX 525 ACL.