New Installation of Windows 10 using Memory Stick

Similar Questions

• New installation of Windows XP does not - UNMOUNTABLE_BOOT_VOLUME

  I'm trying to do a fresh install of Windows XP.

  Soyo SY - P41 845PE Lite MB
  Pentium 4, 2.4 GHz
  1.5 GB of Ram

  This is a computer that I use every day and who usually has a hard drive with WindowsXP SP3. I just want to have a spare hard drive with a new installation of Windows XP on it.

  But installation can not. Usually to auto restart after step 'Copy files' of the installation process. The Windows splash screen appears briefly, and then blue screen message, "a problem has been detected and Windows has shut down to prevent damage to your computer. UNMOUNTABLE_BOOT_VOLUME"followed a few Advisory paragraph which does not apply because the operating system is not yet loaded, then:" technical information: * STOP: (0x8951c900) 0xc0000185 0x00000000 0x00000000. "

  Once he got as far as the Windows Installer screen (one who tells me it will take 39 minutes down left) then a box seemed to read: "Fatal Error. An error was encountered which prevents the installation to continue. Installation failed to install the product catalogs. This is a fatal error. The Setup logs files should contain more information. "Read the Setup log file:" error: the signature for the installation of Windows XP Professional is not valid. " The error code is 80096001. An error occurred during trust verification. »

  Another time, after you press enter in the "WindowsXP installation on the selected element", I INSTANTLY got a screen which read; «An error has occurred during installation has been updated of the partition information on 152626 MB disk 0 at Id 0 on bus 0 on atapi [MBR].» Setup cannot continue. »

  Things, that I already tried that did not work:

  Using two different Windows XP Professional installation disks.

  Withdrawal and tries to install with different RAM sticks in place.

  Two IDE 40 son different cables, which work fine on this computer.

  Two different Western Digital disks hard two test without error using the WD diagnostic utility.

  My knowledge is limited, but that seems to leave only a bad card mother, right?  However, as I say, the computer works well with this old install Windows XP on it. He simply refuses to let me do a new installation on another hard drive.

  What other steps can I take to get a new installation on a hard drive with this computer?

  Thanks to each of you for your attention to my problem.

  I spent $4 on a 80 wire cable IDE (to replace the 40-wire cable I used) and I was finally able to get Windows XP installed today.

  Because I had done installations in the past with the 40 wire cable, I don't understand why it didn't work anymore. I guess the age of the cable, but I actually had multiple failures with a whole new thread 40 I had just bought. A mystery, but at least I now have a new facility and I am inclined to believe the 80 wire will make for a faster computer.

• Satellite Pro M70-137: can I use Memory Stick Pro Duo?

  I think to buy a new digital camera from Sony, witch uses Memory Stick Duo Pro. I'm not used to Sony memory cards, so I don't know if my Satellite Pro M70-137 of the 5-in-1 built in card reader can be used with Memory Stick Duo Pro. On Toshibas Web site, it says Memory Stick, Memory Stick Pro, but nothing on Memory Stick Duo Pro.

  Can we read/write Memory Stick Pro Duo with the build in the 5-in-1 card reader?

  Hello

  I found the info you can use Memory Stick Pro 256 MB to 1 GB on your device. I put t really know if you can use a Memory Stick Pro Duo. Check it please in the user manuals.

  If this is not the case, there are solution called Memory stick duo adapter. The example that you can find on http://www.pc-memory-upgrade.co.uk/memory/memory-stick-duo.asp

  Good bye

• New installation on windows 7 pro 64-bit sees not connected wired Officejet 6500 E710a-f

  Hello!

  New installation of Windows 7 Pro 64 bit on a gigahertz 3.40 AMD Phenom II X 4 965 with 8 GB of ram. Printer drivers worked on the same bench while he was running as Windows 7 Pro 32-bit.
  After only install FF, AVG, and Acrobat (almost a clean install), downloaded the software HP Officejet full feature and pilot 2012-10-22, Version: 116,98, 28.8 M - OJ6500_E710n - z_1315.exe and tried to install the Officejet 6500 E710a f.

  The printer has a manually set static IP and can be ping from the host. Clean Windows Firewall is disabled and stopped.

  The web interface using the IP address of the printer comes with all the features works on FF.
  Network status shows connected with IP address, hostname and Mac.

  However, when installing the network audit is no ethernet connection. Even manually enter his public static IP address or hostname does not solve the problem.

  Try the USB, the same question option. I see in Device Manager under other devices HPOfficejet 6500 and 6500 HPOfficejet - Fax with a blue questionmark.
  (In the same "other devices" there are 2 Officejet 6500 with a yellow exclamation point - probably from failed network installation).

  In the printers and devices window, the 6500 is displayed with the correct thumbnail, but with a yellow exclamation point icon. Law and by selecting the convenience store, Windows comes up with the message that no driver is installed and offers a solution.  The correction ends with the error that no drivers not found for the FAX. Re-apply the patch never finds the driver.

  Anyone who has met something similar (and a solution)?

  Thanks for any help!

  Jack

  After trying to do an install clean-install of 100% and once again, the driver software could not find the printer name or IP address.
  Back at each stage, I noticed that I was not using the correct driver! For some reason I D/L the pilot E710n which is for HP Officejet 6500 a Plus e-All-in-One.
  Whatever the difference, when installing the E710n for the model does not detect the printer, or via USB or Ethernet.
  After you download the right driver for the E710a - f HP Officejet 6500 a e-All-in-One Printer (OJ6500_E710a - f_1315.exe) installation perfectly finished in a few minutes and everything goes well...

  You would think, base or USB connectivity network should not be dependent on the specific differences sub-model. I was expecting that a bad driver interrogate the device after finding its IP address and display an error message with useful text.

• HP ENVY m6-n113dx Notebook PC: new installation of Windows 8 on HP Envy and with problems of drivers.

  I have a laptop HP Envy M6 and it came with Windows pre-installed on it 8.1. I always do a new installation of Windows, whenever I have buy a laptop that I hate all the bloatware and stuff which they pre-install on it.

  Unfortunately, when I did, I found that the drivers on the HP website do not work for some things, especially my wi - fi.

  In Device Manager there are three things that make their appearance as having a problem:

  Network controller:

  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01

  Unknown device:

  ACPI\VEN_HPQ & DEV_6001

  Unknown device:

  ACPI\VEN_HPQ & DEV_6007

  If anyone can provide me with some drivers work, I would be incredibly grateful. I called HP and they told me all I can do is to pay $40 for a CD delivered to me so I can reinstall the version of bloatware, and I really want to do. I want to use my real version of Windows 8 and not pay for something I don't even want.

  Thank you!

  Nevermind, I fixed it myself by reading old son of Paul_Tikkanen

  I used http://www.pcidatabase.com/index.php

  and found the diver that I needed, and now I don't have to pay $40 for the version of bloatware.  Yay!

  Thank you Paul!

• How to perform a new installation of window 8.1?

  Hello

  (If this is important), I use an Alienware X 51 R2 with the following specifications:

  Intel i5 4440U 3.3 GHz processor

  AMD R9 270 2 GB

  8 GB RAM

  1 TB HARD DRIVE

  Basically, my alienware has had many recent accidents before I made my own window installation 8.1 via the USB port. I thought it will run more fast and smoother after I have done, but here are a few problems:

  1 secure Boot product still "no error of Boot Drives Found" as soon as I turn on the computer. So I have to disable Secure Boot.

  2 application opening time is still as slow as before the clean install (i.e. Chrome)

  So, is there a procedure step by step on how to perform a new installation of window 8.1? I want this PC to match at the beginning when I first bought.

  Any help would be greatly appreciated.

  Thank you

  Tin

  You must prepare installation media is to present FAT32 the GPT partition scheme and parameters of the UEFI BIOS with secureboot. See here for more details:

  http://dellwindowsreinstallationguide.com/download-Microsoft-Windows-and-Office/Download-Microsoft-Windows/download-Windows-8-1-retail-and-OEM-ISO/

  You can perform additional steps to clean your drive before installing Windows:

  http://dellwindowsreinstallationguide.com/cleaning-up-a-drive-format-vs-secure-wipe-SSD-and-HDD/

  For complete instructions, see here:

  http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/a-clean-install-of-Windows-8-1/

  Note You may want to complete execution F12 diagnostic tests to verify the correct materials:

  http://dellwindowsreinstallationguide.com/F12-Preboot-Diagnostics/

  If you want to speed up your system to get rid of the mechanical HARD drive and replace it with an SSD for example the 250-500 GB MX200 Crucial:

  http://UK.crucial.com/GBR/en/compatible-upgrade-for/Alienware/x51-R2

• key Windows 8 for the new installation on windows 8.1

  Hello

  Anyway we can use key windows 8 to install windws 8.1 fees

  Thank you

  Hi Imran,

  You can't use the product key Windows 8 If you perform a new installation of Windows 8.1. The recommended method is to install Windows 8 and upgrade to Windows 8.1 by store. You can use the upgrade product key to Windows 8.1.

  For more information, see this article.

  Updated to Windows 8.1 : FAQ

  http://Windows.Microsoft.com/en-AU/Windows-8/upgrade-to-Windows-8

  Hope this information helps. Response with status so that we can help you.

• After the new installation of windows installation

  Hello

  My computer has receantly had virus problems and I want to do a new installation of windows.  After I do this can I reinstall my copy of creative suite and use the code provided to or he'll tell me its already in use since technically, I did use it once already?  If Yes is it possible around it?  I really don't want to drop $800 again just to reload windows on my computer.

  Thanks for any help!

  Disable your existing installation of Creative Suite for free activation.

  Open any application e.g. Photoshop then help > Deactivate. That will disable the entire suite.

  Reinstall Windows.

  Reinstall the Creative Suite and it reactivates during installation.

• upgrade to Windows 7 64 bit Ultimate Edition with the new installation of windows XP

  I plan to upgrade to Windows 7 64 bit Ultimate Edition with the new installation of windows XP

  my PC configuration is like below:

  Card mother Intel DH61WW
  Processor Core I3 2100 3.1 Ghz
  4 GB OF DDR3 RAM
  Seagate 1 TB SATA HARD drive
  OS: Microsoft Windows XP Professional SP3

  I run Windows 7 upgrade advisor in which some results below the incompatibilities:

  Intel (r) 6 Series / C200 Series Chipset Family SMBus Controller - 1 22
  Unknown Intel we have not the compatibility information about this device.
  Intel 82579V Gigabit Network Connection
  Unknown Intel we have not the compatibility information about this device.
  Realtek High Definition Audio
  Realtek unknown we have not the compatibility information about this device.

  Here's my conceerns:

  What needs to be done to overcome the problems of incompatibility?
  Do I need to download new software files compatible for windows 7 and then install
  for example VLC media player, Skype, MySQL Server I am running
  or currently existing files are compatible to install with Windows 7?

  Would I be able to upgrade to windows 7 without any problem and safely?

  Could you please help me with the questions above?

  Please correct me with additional suggetions that I may have missed with.

  Looking forward to hear from you

  Thank you

  You understand that you will not be able to upgrade Windows XP to Windows 7?  He will have to do a clean install.

  The Council supports Windows 7, you can get the drivers here (the chipset drivers should be the first drivers you install after installing the operating system.)

  John

• new hard drive - what is the difference in performance between the new installation of Windows 7 or a clone of old hard drive?

  I get a new hard Hard Drive (SSD).  The new disc is the same size as my existing SATA drive.  I can do either a new

  the installation of Windows 7 or a clone old hard drive?  I would prefer to clone the old hard drive and keep all my settings, etc.   It's empirical data on the performance difference between a new installation of Windows 7 or to continue with the Windows 7 which was 3 or 4 years ago.

  I know the conventional wisdom is that the new installation is faster, but, no matter who actually tested and compared the differences?  I know I'll get better performance of the SSD the SATA drive, but I don't know if it's worth the hassle to do a fresh install and redo all my programs and settings.

  Others that the performance of the SSD you should not see any differences.  If you do, you can always do a clean installation later.

• My C:\ Total size of the disk was 1 TB, I shrunk it once, may I take part in the new installation of windows without losing my files that are on my other partitions?

  My C:\ Total size of the disk was 1 TB, I shrunk it once, may I take part in the new installation of windows without losing my files that are on my other partitions?

  My current C:\ Size of the drive is 500 GB (I shrunk it once).

  Thanks for help.

  See the following topics:

  http://notebooks.com/2011/02/25/how-to-create-a-simple-partition-in-Windows-7-quick-tip/

• Is it possible to perform a clean installation of Windows 7 using an external USB DVD drive. We will ask for a driver

  Is it possible to perform a clean installation of Windows 7 using an external USB DVD drive.  We will ask for a driver.

  I did will need you you will need to Prime boot in the BIOS and set to boot from it.

  For information about how to modify your BIOS options to boot from the DVD drive, see the following tutorial:

  http://notebooks.com/2011/05/05/How-to-load-BIOS-and-change-boot-configuration/

• My new installation of Windows 7 freezes randomly,

  My new installation of Windows 7 randomly freezes, the screen goes black and says "no signal".

  I can't turn off my computer except by disconnecting it., which means that the power button does nothing.
  I did a clean reboot with all the MS drivers without disabilities and she always does, so it is not a software conflict according to Ms.
  I am quite at a loss of what to do now; self-help told to ask here.
  I see a lot of complaints of this nature but no resolution. Very frustrated.
  Can someone please?

  Right now I have disabled all features of sleep on hard disks and screens and power. Also, I took leave fan I added via a double fan--> cord a brooch that I just bought. So far he collapsed again and it's good at the time, I started to wait for an accident. I will continue for a few days like that and then if all goes well, I will add back the fan see what's happening, and then after that undo the change of parameters of power, I did.

• 5.0.3 new installation of Windows 7 x 64 black massive flicker!

  New MacBook Air on OS X with Intel HD 10.8.4 5000. Installed VMWare Fusion 5.0.3 and import a virtual machine since version 3.1. Install a new copy of Windows 7 x 64 as from a physical device. Here's a video (attached) of what the screen whenever the mouse passes over the top of the VMWare window, with the old and new installations of Windows. Note that it is not a problem when VMWare is not the active window, and the flicker follows the mouse vertically.

  So far, we have tried

  • Disabling 3D acceleration
  • change the mouse pointer
  • VMWare running in troubleshooting mode
  • VMWare update
  • relocation of the VMWare Tools
  • check Windows Update for a new video driver
  • VMWare running with compatibility of version 3

  Found the solution in this thread: scrapie form with merger 5.0.3 on no later than 2013 (Haswell) MacBook Air

  Must manually edit the .vmx file and add the line mks.vsync = "1" "

• New installation of Windows, cannot be updated, use the troubleshooters, install some drivers, etc.

  I just got my new pc in the mail, put everything together, things are going wonderfully.

  However, my old motherboard installed my hard drive as IDE, while my new motherboard used alone RAID or AHCI (im using the same hard drive for my new pc) and so I just reinstall windows using my installation disc. And when I loaded in windows, I installed my card drivers mother perfectly fine CD. However, I can't use windows update, even after the validation of windows. All convenience stores read "a problem is preventing the troubleshooting tool to start" (0x8E50247 error code) actually ive been awarded the xxxxxx247 codes error then Yes. Help, please. I want my PC to normal

  PS I have all my old files always in my windows.old folder. Can I just set that up somehow? If my computer is back to how it was before the passage of material?

  Hello

  To troubleshoot Windows Update in Windows 7, we suggest that you follow these methods below and see if it helps.

  Method 1: Reset the Internet Explorer settings.

  You can reset the Internet Explorer settings to return to the State they were when Internet Explorer has been installed on your PC. This can be useful to solve the problems that could be caused by some settings changed after installation.

  Note: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Also re - activate the Add-ons.

  Please click on this link to know how to reset Internet Explorer settings.

  Method 2: Perform the clean boot

  A clean boot is executed to start Windows by using a minimal set of drivers and startup programs. This will eliminate the conflicts of software that occur when you install a program or an update or when your run a program in Windows.

  Click this link to learn how to perform the clean boot in Windows 7.

  Note: Please see: How to reset the computer to start as usual after a clean boot troubleshooting section of Kb to start the computer to a normal startup after you fix the problem.

  Method 3: Run System File Checker scans to check corruption of system files.

  1. Press the Start button, then type cmd.
  2. Right click on cmd and select run as administrator.
  3. If user account control dialog box appears, confirm that the displayed action corresponds to what you want, and then click continue.
  4. Copy and paste the following command in your command-line prompt: sfc/scannow
  5. Press enter to execute the command. It may take a few minutes to complete. If you find 100% full reorganisation, click X to close the command prompt.

  Let us know the result.