No fax only print connection

Similar Questions

• HP wireless printer (3545) showing only printer and scanner, connected via Wireless

  When I connect via USB, I see Print/Scan option in the settings system-> Printers & Scanners

  But when I connect through wireless, I only Print

  What is the problem?

  Even in the HP utilities, I don't see this option "Scan to Computer" when it is connected to the wireless printer

  Hi TahseenJamal,

  Thanks for the video, which has been most useful.

  I suspect that the router can be not broadcast the Hello Protocol as it did in the past. To resolve this problem, please follow the instructions below.

  1. Out of the router, unplug the power cable
  2. Out of the printer, unplug the power cable
  3. Stop the Mac
  4. Give up everything for 1 minute and then reconnect the router
  5. Once sighted routers are on, reconnect the printer to the
  6. When the wireless printer is solid, turn on the Mac
  7. Now try to add the printer that you had previously, you should now see the Hello or Hello printer multifunction beside him.

  If this does not resolve the problem, it could be the printer. Follow the steps below.

  On the front panel of the printer, the arrow down to settings, then press OK. Down arrow for wireless and press OK. In the wireless menu, go to IPV6 and turn it off. Once IPV6 is disabled, try to add the printer in the preferences system again.

  Please let me know if either of these solutions solve the problem and if one of them, please also let me know, thanks.

• 8500 A909G - Feeder causes black streaks on faxes/scans/print jobs... ONLY when you use the charger

  Charger cause black streaks on faxes/scans/print jobs... ONLY when using the charger... If I put something on the glass and printing fax/scan/or it... everything's fine... it was ONLY when I use the charger... did someone come up with a solution to this problem?  Looking at the other reports, it was NOT those that have been fixed... I hope that someone can help me solve this problem, as it was NOT a printer not expensive to buy...

  I'm sorry you have a problem with the vertical lines in the ADF.

  Try to clean with water and lint rollers. There is also a glass of small strip (rectangular) when you lift the lid. Also clean.

  Here is a link that can help you too.

  http://support.HP.com/us-en/document/c01618140

  Let me know if it helps.

• OfficeJet Pro 8625: printer shows as fax only

  The State of the printer indicates that it is configured.  I am able to print from my laptop (WiFi), but not from my office (WifI).

  Jobe feeling all enter fax, no printing.

  Hello

  Please try

  Click Start > devices and printers

  Right-click your printer, and then select set as default.

  In the opposite case

  Download the following tool and run it on your computer:

  http://ftp.HP.com/pub/softlib/software13/COL50849/MP-145514-4/HPPSdr.exe

  or

  re-install the software and driver.

  Kind regards.

• want to 5540: can I leave my printer connected 24-7? Does go in mode "sleep"? I print every day!

  Can I leave my printer connected 24-7?  Does go to sleep mode?  I do not see every day or week necessarily!

  According to the manual (HP Envy 5540 all in a manual series) on page 22, it goes into powersave mode after 5 minutes of inactivity. You can change this time in the control panel if you wish.

  After 2 hours of inactivity, the printer will automatically turn off, and you have to press the power button to restart. This auto off function is not active if the printer has wireless or WiFi Direct features turned on. Or if she has a fax, Ethernet, or USB connection. This info can be found on page 23 of the manual linked to the previous paragraph.

  -dave

• HP ENVY 4507: Envy 4500 only prints a PDF from PC

  OK, so this is the 4th or 5th time I posted on this useless printer. Now for almost 6 months. And 3 different HP printers. I can only print from PC in pdf format. If I select a word doc or printing online. The printer icon loads and that's it. It does nothing else. There is none of the queues. I'm so fed up with it. I will never buy a HP item ever. Includng the desktop PC, I was sold as a gaming PC. With a 545GT graphics card. I can barely stay on the line as overheating but it's a whole different story lol., I just want to do what I did with each printer ther I used. Press on print and it prints. Why are there 2 profiles? Series 4500 and 4500 networking. I have uninstalled re-installed and tried all the work around known to humanity. Wil still only print to PDF files and nothing else. Please can you help me. This is my last attempt to fix this printer. In the case of failure embarks on a garbage depot. I used to promote HP products, but not more. They have dropped the ball. Cheap and nasty with components not conforming to standards hidden inside the material. Made in China is a big attention I'm afraid.

  Kind regards

  Mabrouk

  Hi @zookeeperz,

  I read your post and see that the printer will only print the PDF documents. Usually, it's the opposite. I want to help you.

  You use the latest drivers? Here is a link if you need it. HP ENVY 4500 e-All-in-One Printer full feature software and drivers series.

  If the printer is listed as the 4500 series and the networking of 4500, then most likely the USB and a network driver are both installed for the printer. It is in the devices window and printers?

  Download and run the print and Scan Doctor, he will diagnose the problem and could solve it automatically.

  I suggest to install a generic driver to see if you have the same results.

  On the computer, go to start, devices and printers, right-click on your printer and select printer properties.

  Click the Advanced tab and click new driver, and then click Next.

  HP Deskjet 9800 by selecting in the list or the Deskjet 990c printer, click Next, Finish, and apply the settings.

  (you can always go back and revert to the original printer driver)

  How is the printer connected? (USB, Ethernet, WiFi)

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If you appreciate my efforts, please click on the "Thumbs up" button below.
  Please let me know the results. Thank you.

• Photosmart c3180: c3180 will only print in fast draft mode

  I can only print in fast draft mode.  If I try fast normal, normal, or best etc. the paper through the machine and it spits out without printing. If I have multiple pages to print, it only spits out a no printed page and then closes.   I tried to print in many different programs and they all have the same law.  It makes no difference if it is color or black and white.

  Hi @kbsh9884

  I think it would be better to start our trip troubleshooting by running the print and Scan Doctor (PSDR). Printing HP and doctor Scan is a free utility (tool) that allows to quickly solve common printing, scanning and connectivity problems, including but not limited to:

   

• I have a HP Officejet used that only prints black

  Hello! I recently bought a HP Officejet 4500 used. I use it as a printer with my MacBook Pro version 10.9.3 and it will only print black. I have combed all through information from print and can't find where to change the settings to print in color or black. Also, how can I connect it via Ethernet? Thank you!

  The Officejet being able to print colors without problems when compared with the computer, we have a path take it now. Try to reset the system of printing on Mac, this will delete the printer drivers, when return adding that it will be the default settings. Mac OS x: how to reset the printing system will guide you if you have not done this before.

  Now that the printer drivers are deleted, repair disk permissions on the computer. Download and install this: v.2.16.1 for OS X HP printer drivers and add your printer. There should be no reason why the printer would not print color of the computer.

• Impossible to only print from message WORD get no installed printer

  I have AM UNABLE to PRINT IN WORD - GET MESSAGE "NO PRINTERS INSTALLED" - AM ABLE to PRINT FROM WORDPAD, EXCEL AND INTERNET.  Help!

  In general, you should ask questions related to the word in the Word forum: http://answers.microsoft.com/en-us/office/forum/word

  Before you do so, however, it may help: http://support.microsoft.com/kb/223418 are most likely parts of this article apply to your situation:

  Set a different default printer and set your original as a default printer.

  If you do not have a second printer installed, install the 'generic - text only' default printer and then set your normal printer back to the default value:

  1. Click Start , click Printers and faxes.
  2. Under printing tasks, click Add a printer, and then click Next.
  3. Click local printer attached to this computer, and then click Next.
  4. In the use the following port box, select LPT1: (recommended Printer Port), and then click Next.
  5. In the manufacturers list, click generic.
  6. In the Printers list, click on generic / text-only, and then click Next.
  7. Check the name of the printer, and then click Next.
  8. Click do not share this printer, and then click Next.
  9. Click No when you are prompted with the question whether you want to print a test page, and then click Finish.

  To change the default printer and the new driver, follow these steps:

  1. In the Printers window, click generic / text only printer (or your other existing printer), and then click set as default.
  2. Right-click your original printer and then click set as default.
  3. Try printing again.

• OJ j6480 all in one. : printer connected to the network, but will not print.

  OfficeJet j6480 all-in-one Windows 8

  My printer configuration report show that the printer is connected to my home network. My Control Center shows that my HP printe (my only printer) is listed as the default printer. When I open it, it shows a document in the queue, and offline. When I click on 'offline' the document in queue is considered and when I click on "Printer" in this window, the drop-down list displays the default printer, but 'use printer offline' isn't not verified. Bottom line, it's that I can't print. Help much appreciated woutd.

  I found someone with a similar problem and a simple solution. I deleted my printer in the "devices" list and reinstalled

  It worked. I suspect that your suggestion about the IP was probably on the brand, it had not occurred to me.

  Thanks for the quick response.

• When I try to print on a printer connected to my win7 I get code "printer not responding" 105-100003

  How to fix error code 105-100003

  I am running windows7 on my host network and vista on the other computer. I am able to connect to the correct internet on vista computer, but when I try to print on a printer connected to my win7 I get code "printer not responding" 105-100003. I printed before and I have not changed or added to any software since. Both computers are desktop computers and connected by ethernet cable. I have run diagnostics and checked all cables. I have a modem 2 son I had about 2 months.

  Hi, Jimmy.

  Make the printer and model would be useful.  Thank you.

  Try the following:

  If your printer is connected via a wireless network:

  1. Make sure that your printer is turned on. (Start button / stop is turned on).
  2. Make sure that the blue LED of Wi - Fi on the front of the printer is on and stays on.
     • If the blue wireless LED flashes, your printer is not connected to your router.
     • 1. Follow the steps in the configuration of wireless network Guide (named the network installation Guide, if your printer has Ethernet printer capabilities) to connect your printer to your router.
       2. If you are unable to connect the printer to the router:
          1. Turn off the power to the router, and then turn on the router
          2. Follow the steps described in the [wireless] Network Installation Guide once again.
          3. If necessary, see what should I do if I can't configure my all-in-one printer (including the connection of wireless configuration)?
  3. When the blue LED on Wi - Fi from your printer stays on (not flashing):
     • If the error ' printer does not "occurred while you have been setting up the printer:
     • 1. Open Software Center.
       2. Select the tools of the printer, and then select Printer Setup Utility (under Tools).
       3. Follow the on-screen instructions to set up the printer.
       4. Try to use the printer again.
     • If the error occurred after you completed the roll-out of your printer from Home Center Software:
     • 1. Make sure that the print queue is online.
       2. From your computer, click Start > settings > printers and faxes (or start > printers and faxes).
       3. Click on your printer.
       4. In the printer menu, make sure that use printer offline is not checked.
          NOTE: These steps may vary depending on your operating system.
       5. Try to use the printer again.

  If the error persists:

  1. Remove the printer from your computer.
     1. Select start > settings > printers and faxes.
     2. Right click on your printer, then click on remove.
  2. If your computer is WINDOWS VISTA or WINDOWS 7 OS, turn user account control.
     1. Select start > Control Panel.
     2. Double-click user accounts.
     3. Click turn user account control on or turn it off.
     4. Select the check box use user account control.
     5. Click OK.
  3. Configure the printer again.
     1. Go to start > programs > Kodak > Kodak Printer Setup Utility.
     2. Follow the on-screen instructions to set up your printer.
  4. Try to use the printer again.

  If the error persists:

  1. If you have updated to the Home Center Software v6.x or greater, disable the Hello Service.
     1. Select start > run.
     2. Type services.msc in the box, and then click OK.
     3. Locate and right click on the Hello Service and select Properties.
     4. Since the "Startup type:" drop-down list, select Disable.
     5. Click OK.
     6. Locate and right click on the network AiO Kodak Discovery Service, then select restart.
  2. If you configure your printer, run the KODAK printer setup utility.
     1. Select start > programs > Kodak > KODAK Printer Setup Utility.
     2. Follow the on-screen instructions to set up your printer.
  3. Select the Hello Service.
     1. Select start > run.
     2. Type services.msc in the box, and then click OK.
     3. Locate and right click on the Hello Service and select Properties.
     4. Since the "Startup type:" drop-down list, select automatic.
     5. Click OK.
  4. Try printing from the center of renovation again.

  If the error persists:

  1. Make sure that any firewall software blocking the required services and that it does not block the firewall of the router. See cannot use a wireless printer to computer on the same network with firewall security program.
  
  NOTE: If you use BitDefender Total Security 2010, the problem can be solved by turning on the game mode in the firewall. If it does not turn on the game mode, temporarily disable the firewall to enable wireless printing.
• Make sure your computer is not connected to a virtual private network (VPN) or wireless home another network of safe working when you use the printer on your network. See using printer with the virtual private network (VPN).
• Check that your printer is not connected to the network trouble with the same name (routers with the same default SSID in your area). It is common for users to keep the value by default, out-of-box, SSID as the manufacturer provides (for example the linksys). If your router still has the default SSID, change the SSID under a new name specific to your router.

NOTE: updated to the latest version of the firmware of the printer and the software when prompted will help you have the most reliable connection possible. Go to www.kodak.com/go/aiodownloads.

If the error persists, contact us.

http://support.en.kodak.com/app/answers/detail/A_ID/36674/selected/true

• My HP C5280 printer only prints part of photo

  Original title: Mr

  My HP C5280 printer only prints part of photo

  My HP C5280 printer only prints part of photo

  Hey BlueWaterParadise

  ·                        try to uninstall and reinstall and use the latest printer drivers for your model of hp

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the other links here

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Walter, the time zone traveller

• DeskJet 2540 all-in-one: Deskjet 2540 only prints PDf files

  I got a 2540 for my grandfather a few weeks ago. When I put to him that it worked fine. Now, however it will only print opend with Adobe pdf files and I have no idea why.

  Any other print command will result in a blank page or a page with a few veins of black or color. It will not display even a test page.

  This could very easily be a problem with the machine of my grandfather because it is very old and running Windows XP 32-bit. I also have no way to connect his machine on the internet before taking him home and update mine and I prefer not to do so.

  I tried to download the drivers on an external device and then editing them, but that has done nothing to solve this problem.

  Any ideas?

  Thanks for the replies

  It is black ink. It must have been damaged as when I replaced it with a new one that he started printing very well. The reason why that worked the pdf was because it was all in color and like the fool that I am, I have not noticed.

  Thanks for the quick response.

• printer connection

  I recently bought a hp Pavilion p6 2335ea to replace an old pc from dell.  Two dell computers were connected to my printer, a device All in hp officejet 4315, via a belkin device, which is passed from one user to another.

  The new pc works fine with the printer connected directly, as does the old another dell, but does not connect via the belkin.

  How can I reconnect the system so that the two PC works with a printer?

  I don't understand, and this Board is still topical. You're trying to network a printer between multiple computers through the Belkin router. However, the difficulty lies in the fact that it is a Deskjet and it is connectable via a USB cable only. Here, there are two options:

  First of all, if the router has a USB connection, you can connect the printer via the router and use the Add Printer Wizard:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_setup_indirect_printer.mspx?mfr=true

  Second, you can install the printer via a computer and share the printer through the network. You must set up the computer on the network as a designated working group and share the printer through that.

  http://Windows.Microsoft.com/en-us/Windows/sharing-files-printers-help#sharing-files-and-printers=Windows-7&V1H=win8tab1&V2H=win7tab2&V3H=winvistatab1&v4h=winxptab1

  These are your best two solutions with this printer, but I would recommend get a printer with at least one Ethernet connection - this would simplify the networking of the printer in a simple and clean process.

  I would like to know how this happens and have a great day!

• Aspire One D255E don't look for a printer connected to the USB port

  My D255E an Aspire don't look for a printer connected to the USB port.  I've never used a printer on this computer before.  Windows 7 Starter will support a printer?

  It should be.  Try these steps and results reports:

  When you turn on and connect the printer via USB, shows tasks for animation in the system tray at the right end of the bar, click it and monitor driver installation.  If the pilot goes then printer must print and perhaps scanning of base via the Windows fax and scanning utility.  To find such a piece of utility type its name in the search box.

  If the driver does not load type of devices and printers in the box to start the search, open it, check if printer is already displayed, right-click on it to open the properties, and try to print a Test page. If it does not print right click on printer again to solve problems.

  If the printer is not listed visit Support downloads of the printer Web page to download and install the base driver.  If a wireless printer, you will need the complete package to do it fully implemented.  If you want to be able to scan from the top of the printer to the PC, then you also need the full package.  Keep track of the configuration screens when you install the software.

  If you still have problems after return the exact error with photos if possible.