Paper size and locked type

Similar Questions

• All-in-one HP Officejet 6500 has: paper size or the type of error message problem

  I have a HP Officejet 6500 all-in-one a and am running Win 7 on a desktop computer.
  I get a paper mismatch (type and paper size is incorrect) error message.
  The printer is not connected to the internet, but it is connected by a USB cable to the computer.
  I look at the instructions to make an internet connection and they were just too complicated. So I download the update of the firmware and ran to the computer. He would not go beyond the area of printer selection where no printers were found. Clicking Refresh has not helped.
  This update of the firmware seems to have solved the problem for some users, but I need to know how you install it.
  Thanks for your help.

  17/03/2015 #2

  I think I solved the problem. I went to the website to download drivers, etc., and, rather than to specify the printer, I clicked the button to let HP identify it. It came with the correct name (see post) preceding. Then, I downloaded and installed the full feature software and driver. The first attempt to print from Excel led to the mistake of page size, but, on a whim, I tried twice and had two successful prints without error. Until further notice, I mark this as solved problem.

  Thanks for your help,

  LK

• HP Laserjet M401A: HP Laserjet M401A not will mark the different paper size and tray on the printer properties

  Hello all.

  I have a custom paper size in question and the plateau in the properties of this printer.

  I would like to implement three different printers on the same port, to print directly on a specific tray (without going into the properties of the printer and select the appropriate tray and size).

  I have this printer with the additional third tray.

  I implemented the A4 in the Tray 1 (bypass), a custom size in tray 2 and 3 on the printer.

  When I enter the printer PROPERTIES I want to set up the paper size in tray 2 and 3 value. No question.

  The only sizes I see is 13 x 8, a4, a5, letter, legal and so on (there are choices may 7).

  So, I choose NON SPECIFIC.

  When I go to printer PREFERENCES, I can set up my custom paper size.

  But when I choose my custom paper size, tray 2 and 3 go away and I can choose only bypass or Tray 1.

  If I attributed to A5 (for example) the tray 2 and 3 re - appear.

  How is that possible? where I'm wrong?

  Thank you very much, any help would be appreciated.

  See you soon,.

  Luca.

  Hi Luca,

  That is expected, custom paper sizes are supported only on tray 1.

  Tray 2 and 3 are supported specific sizes of paper.

  You my find graphics of the following as a reference, it lists a paaper supported size for each tray:

  http://h20566.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=5096252&docid=emr_na-c03303423&docLocale=en_US

  Kind regards

  Shlomi

• the paper size, and paper also prints the profile color inkjet

  I intend to use an inkjet printer to print at least one (or more) copies of a drawing of YOUR CONTINUOUS created in Ps CC 2015. I have several questions about the TYPE of DOCUMENT and the ADVANCED OPTIONS:

  
  

  1 Wkind of hat of paper do I need to buy, and should I use one of the presets U.S. PAPER?

  
  

  2. If I don't want to design to BLEED on paper, should I create the design that is smaller than the HEIGHT and WIDTH I choose (e.g. would allow a larger size such as 8.5 x 11 for the margins between the edge of the paper and the design itself)?

  
  

  3. is it true that inkjet printers are usually set to 240 and, therefore, the image of RESOLUTION must not exceed (eg. something higher is too much data for the printer to process in a reasonable period of time and there is no difference in quality anyway)?

  
  

  4. should I work in RGB mode and CONVERT them to CMYK when I finish the design?

  
  

  5 should I use the default PROFILE of COLOR RGB (sRGB IEC61966-2, 1), Adobe RGB (1998), the "color management this document" option, or some other?

  You'll want to experiment with the printer.  Save copies of the file in separate RGB profiles as I explained in my post.  You will be surprised on the different color prints, you will be able to achieve.  As you work in a workspace 'closed circuit', you can print RGB strictly.  This will allow a wider range through the barrel.  Certainly use color management in the print driver.  For what is the resolution of the image, use the 140 to 150 pixels per inch.  No interest to enter in the halftone screening technology platform.  Suffice it to say, 300 pixels per inch is unnecessary and too much data for inkjet.

• Physical size and the type of disk hard drive in my XPS M1210?

  Hi, for the first time poster here. I'm about to buy a new hard drive to replace the original one in my XPS M1210. I just need to know the physical size (3.5 "? 2.5"? etc) and type (7200 rpm or something else?) of him so I don't know the correct type to buy and replace by.

  Thank you!

  notch16

  The physical size of the SATA hard drive is, 9.5 MM x 2.5 ", either 5400 or 7200 RPM works perfectly.

  Bev.

• Paper size and the size of the cells do not match LR4

  Hi I have a prob with the format and size of cells not matchng in LR4 using a Sony UP-DR150 printer.

  I'm running on Windows Home premium 64-bit.

  I installed the Sony 64 bit printer driver.

  When I print the photo, it prints the size of 4.31 x 3.12 on 5 x 7 paper.

  can anyone help?

  

  

  I put my printer paper 5 x 7 (no border, of course)

  gutters and margins not controlled

  moved all margins to 0.0

  then changed the layout height and width of 5 x 7

  everything is fine!

  -janelle

  Give it a try. If your printer does not print 5 x 7 borderless, you might have a problem...

• Have a HP E709N series does not recognize paper size and only prints in color

  original title: have a HP E709N series with 2 numbers.

  (1) fax - does not recognize the format of paper on every page. He feeds a blank page out and I have to press OK to print each page.
  (2) when a print job is qued, it prints in color, not black.  Color cartridges are low, but I am printing black docs.

  Hello

  ·                         try to uninstall and reinstall and use the latest printer drivers VISTA for your model of the manufacturer of the printer

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the information of the links to the other

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  using the information how to use etc. and drivers for your printer, please read the information contained in the links below

  drivers

  Choose vista or vista 64-bit according to your operating system

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3795406&LC=en&cc=us&DLC=en&submit.y=4&submit.x=11&lang=en&cc=us

  and read the information on the use of the manuals troubleshooting etc. for your model below

  http://h10025.www1.HP.com/ewfrf/wc/product?product=3795406&LC=en&cc=us&DLC=en&submit.y=3&submit.x=8&lang=en&cc=us

  If that does not fix it try hp support

  http://h10025.www1.HP.com/ewfrf/wc/contacthp?LC=en&DLC=en&cc=us&lang=en&product=3795406

  or hp support forums

  http://h30434.www3.HP.com/

• Failure of hard drive in Dimension 8250, the maximum size and the type of replacement tips please

  Dimension 8250 (Feb 2003), Windows XP Home SP2, 60 GB HDD, 512 MB of RAM, BIOS A01 - entirely standard

  My hardrive suffers from weird deaf noise for a few months, but last week, it was a lot worse. Sometimes it starts up and is ok, othertimes it takes 1 hour to start and everything produces the deaf noise and is so slow, that it's unusable and other times simply clunks and not even start.

  Error messages received:

  (a) "drive Dell, monitoring system has detected that drive 0 on the primary Eide controller is out of normal, backup specifications and replace the HARD drive.

  (b) "error was detetcted on the HARD disk during the paging operation" (in the event viewer)

  (c) "driver detetcted a controller the HARD disk error" (in the event viewer)

  (d) when I run the Dell IDE Drive Diagnostics (F12), it says FAILED return Code 6

  Issues related to the:

  (1) am I correct that the drive needs replacement?

  (2) I want to just keep it very simple and buy a drive and adapt it, do not worry about BIOS or other upgrades. What I do pay attention to the size car that I buy, is there a maximum size that I can have with BIOS A01? Maybe thought to 120 GB? I just want to be able to adapt, without having to play around with BIOS upgrades so simply the easiest option, which is to buy, set up and reinstall the software. So, is there any limitation integrated with BIOS A01? The recovery CD is XP SP 1

  (3) am I correct that the PC supports up to 100 ATA if you need to make sure that I buy ATA 100 no ATA 133?

  (4) original drive is Hitachi, Seagate Barracuda would be better?

  (5) think active drive a 2 MB cache, a cache 8 MB drive would work ok without me having to pay anything and if yes is it useful on the 2 MB cache?

  Thanks for your time.

  Message edited by craiguk on 02/06/2008 18:27
  Message edited by craiguk on 02/06/2008 18:28
  Message edited by craiguk on 02/06/2008 18:47
  
  

• HP 4520: Eprint and all in a print module won't let me pick the paper size I want to print 5 x 7

  EPrint and all in a print module doesn't let me choose 5 x 7.

  Hello

  Are you referring to the eprint & all in one apps for android?

  Please make sure you have the right selected and that all other paper size and paper type settings are correct.

  Another option is to download the plugin from HP for android (you must also enable it in Settings download afte) and try to print that way. Once downloaded and activated, you should have the ability to print photos directly without going through the applications.

• Paper size for eprint jpg files

  I use a HP 7520.  When I epring a jpg type file, it will only show for the photo tray.  Is it possible to print to the main paper tray?  I don't see this option in the configuration of printer options.

  What ePrint do you use? If you use the ePrint Mobile application, you can adjust application ePrint settings to send pictures to the tray paper. Open the application, select 'photos', select the photo you want to print. Click on print, then select the settings in the upper right of the window. Here you can select the paper size and adjust accordingly.

• paper detected does not match the paper size

  After clearing a paper jam when I go to print the 7310 all in one, beeps and has "paper detected does not match size of paper or type". When I hit OK the printed page is slightly bias. How can I fix it?

  First thing I want you to try is cleaning the rollers.  You said that the printed pages were asymmetrical.  Which can be the cause of the printer read the incorrect paper size and give this message.  The document below the link should help you clear up the problem of tilt.  Let me know what happens.

  http://support.HP.com/us-en/document/c00242765

• Odd paper size does not print on B8550

  Hi all

  I have seen this issue before, but the answers don't seem to work for me, so let's try again:

  I'm on a Power PC Mac dual G5, OS 10.5.8, connected to a Photosmart B8550 via USB. I'm in Photoshop CS4, I'm trying to print on a paper 12 x 15 for which I have a paper size custom, implemented and registered. I try to print to the paper size, and I get a message that says: paper size or type does not match the paper size and type in the in tray.

  The really weird thing is, it worked a few minutes ago, and I do exactly the same thing now. Any ideas would be most appreciated.

  Thank you

  Peg

  No, thanks to HP, I found the solution. The paper type must be HP Advanced Photo paper, and I can print what I want, to any size I want, no matter what program I want.

  Hey, HP, do you think you could indicate this to your support the so-called people?

• OfficeJet Pro 8600 - paper format and copy

  I have an original document which is 216 x 330mm (8.5 x 13 in) and the paper of the same size. I want to copy the document to its original on the document size. When I try this, thumbs down, or so of the original are not copied. Now, for reasons known only to HP, the "Paper size" menu (on the printer) in the copy options gives a very limited number of possible paper sizes, and 8.5 x 13 is not one of them. From there, I understand:

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/unable-to-copy-legal-size-on-HP7610/m-p/297...

  that replace the region of the printer setting affects which paper sizes are available under the menu copy and this seems to be true, but I tried a lot of different countries and none of them include 8.5 x 13.

  My only option was to scan the document and print it then my PC. Note that when you print from the PC the 8.5 x 13 size is available, and if I get the result I want - an enlarged copy on paper of the same size. However, it's much slower just made a copy of the printer, and if I had to copy a large number of documents, it would be really possible.

  So is there a solution to this? I for the life of me don't understand why everyone thought it would be a good idea to limit considerably the range of sizes available destination when copying. What would be really nice would be to have all of the available formats, the same list see you if you go to 'Print Options' on the PC, the printer, what that is the region, and if this list is deemed to be a bit heavy so to choose the settings by default, perhaps in an 'Advanced' options menu

  Hi Bell,

  I cut paper format legal until Folio and tested on a 8600 JO.

  I found that the setting of the copy to legal size and feed the page via the ADF has copied the entire page on Folio paper I created.

  There is no errors if the printer did not bother the paper more short.

• For HP Deskjet 2514 custom paper size

  When I try to print using my deskjet 2514 the document never fills the entire page. I use 8.5 "x 11" paper, but I don't have this size option when I try to change the paper size and I can't find the custom size option.

  Hello

  8.5 "x 11" size is listed as LETTER in the pilot.

  By never fills the entire page, you earn printing without margins? (Edge onboard borderless printing)

  If Yes, do not forget to click the button in the screen printing Advanced Options and set the option to print borderless as borderless printing.

  Shlomi

• What new photoquality garlic in those support paper size in the printer driver?

  I have a new HP Photosmart AIO 7510.  Much to my surprise the printer driver does not support create 6.5X10 inches, 5.5X8.5 inches for card stock for example custom paper sizes.  I used to have this feature in my old HP Photosmart 5150C all-in-one.  My PC is Windows 7 Edition home premium, SP1 operating system.

  Is anyone know 1. What new models - printer or in a single - support a photo quality printing and custom paper sizes?  Am open to return my current template and replace it with a new model of HP.  Or with Canon, Epson. anything that works to regain this ability.

  or 2.  is there another driver that is compatible with the 7510 which will create custom paper sizes and quality photo printing.

  You can use customized with the 7510 paper sizes, but you must use another driver to do it. Follow the steps in the post below the link for your operating system. With the help of the other driver should get the custom print size to work. Hope that helps.

  How to assign other print in different Versions of Windows drivers:
  http://goo.GL/zCk2r