Photosmart 5510 - part dead touchscreen

Similar Questions

• Printing with the photosmart 5510 and MAC 10.7.2 is a dream? and I don't even go to part scanning

  Wauw, buy a photosmart HP 5510 printer and you are very busy for Christmas together to print wireless?

  Unpack your photosmart 5510 and install?

  Well, it prints 1 page and then you get the message printer isn't ready if you want to print your next page.

  1st day, I try with my own knowledge.

  
  

  Updates

  Reset the router.

  Work with difficult IP put in the printer.

  Change the IP address via the Web interface.

  Change the settings of the router

  Try to reinstall the software which is not even possible that most all do the manual says that it is.

  Still 1 print and then nothing. Reset the printer or change the IP in the difficulty of the printer, labour, still 1 print or scan or 1 airprint but then nothing.

  (printed about 35 pages of BS as test)

  Day no. 2, new day of new towers

  Looking around the God thank you forum I'm not the only one who has this problem.

  A lot of people, same problem, some struggle for 6 months, contact support without success.

  Damm scan I even was going to this party and look at all the users having problems. Allow me to first impression please.

  And right now, it looks resolved advice and try to do the same. No results at all.

  Day still no 2, but I can't download now...

  Come on guys read it all, it seems that you are lucky, when it works. You must be a programmer if it works.

  My main question is;

  -Is this or Steve Job knew this?  This product is in its Apple store, HP uses the Apple logo.

  -Sell HP t - he produced cheap now and get the money back to test everything print and use the cartridges?

  -Are there hope or solution let this work smooth with what the box and ads tell?

  -J' just forgot a small no and someone give me the solution?

  -In a lot of wine in these days of Christmas?

  Hope someone can help me and get this Photosmart 5510 working (printing, scanning and airprinting it says on the box)

  Hi ShiomiL,

  A tried these last few months, a lot of time to get the HP works as it should work (especially the airprinting and scan) without any success.  We used with IP printing/scanning, which wasn't a problem, but does not give us the full possibility of the HP printer.

  Today I bought an apple Extreme airport, connect and a few seconds later all works perfect

  In the end, so it was the TL-WR741N (the latter replaced by apple airport) that give problems.

  I just wanted you to know and say thank you for the support you give.

• Server connection error:-1 there is a problem connecting to the server... hp photosmart 5510

  HP photosmart 5510 e - while a printer B111a

  Windows vista 32-bit

  connection error message-Server error:-1 there was a problem connecting to the server, press Retry or ok to continue

  No changes have been made to my operating system

  Try to add new applications with eprint center of my Compaq Presario CQ60 laptop to my HP printer. Computer tells me that the new applications are there and ready to use, but printer says 'server connection error "? I followed all the instructions to connect to the wireless router, but I'm not sure how to connect to the "Server"?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

  Let me know if you have any additional questions. Thank you!

• do not install the driver for XP photosmart 5510

  I tried in vain several times to install the driver for my refurbished XP for my laptop HP photosmart 5510. I said I want to install via radio - he finds the printer and lets me select - then it starts the installation.  It gets about two-thirds through the bar of "installing network printer." "and crashes.

  I let it rest, go to walk my dogs, prepare dinner, and it moves of there.  When I click on cancel, it crashes during the phase cancellation and I'm relegated to "force quit" process.  It's annoying!  All I want to do is wireless printing.  Scanning the computer would be an asset.

  BTW, I had NOT of PROBLEMS installation on laptop of my wife under System 7.

  Help, please... Thank you

  Docswan

  Hi docswan,

  I can't wait to hear that you are experiencing installation problems.  The following steps may resolve this problem. You can also view documents related to this issue by clicking here.  If you are unable to install the full features software, a generic driver can be installed via windows to enable printing only.  Here is a link that will provide the steps to do this.  Click here

  1. connect a new printer.

  2. the software freezes when "control network.

  3 allow software to sitting there for 3 minutes (to fill in the background).

  4. go into the Task Manager process tab.

  5. complete the process of HP network Communicator.

  6. This should push the software to a point to choose wireless or Ethernet.

  7. Select Ethernet or wireless depending on connection.

  8. Enter the IP address manually in the appropriate box.

  9. the software freezes probably during the 'network of control' all or part way through.

  10 allow software to sitting there for 3 minutes (to fill in the background).

  11 go into the Task Manager process tab.

  12. end of the process of HP network Communicator.

  13. This should push the software before saying that the printer cannot be installed correctly, but can be installed via the IP address.

  14. click "continue".

  15. the software should continue and give a green check mark.

• Photosmart 5510 not printing and noises when toggled or asked to print?

  About 6 months ago, we purchased our printer HP Photosmart 5510 alongside our Touchsmart computer, and so far, both work fine.

  However, there are a few weeks at random, when I sent a document to print, the printer started making a very loud noise, sounding almost as if he was that something stuck in the back there. Only to make the noise stop, I cancelled the printing and has turned off, which again triggers intense noise. This back on once again, he made the same noise and, before moving on to the usual display a notice on the monitor of printer flashed by saying that the device had extinguished itself incorrectly.

  It lasts for a few weeks now, and after having scoured your Web site for all the details, I couldn't find anything on this issue. After detecting that other factors may have come into it, I watched some of your videos on how to fix etc. paper jams. After pulling some paper in the back, I thought the culprit of all this, the message on the monitor said he had a 'ink cartridge problem' or could not detect the paper, even if we just replaced the ink and I have to reload the paper. I watched the videos of these two problems troubleshooting and tried 20 seconds thing etc, but nothing worked.

  Really, I'm so frustrated and I would like a little help from a very kind person out there?

  

  Hey mollycat,

  It seems that there is a problem with the power of the printer mechanism paper.  If the unit was loud noises, then it might be a part out of alignment or a piece of paper caught in the unit.  However, you mentioned the continuation of the measures is stuck, remove the paper, and now the printer gives error ink system.

  I will provide documentation of troubleshooting below for the two issues, but if these steps don't erase the question then I would advise to contact HP Technical Support on this printer.  Is it is only 6 months old, then it would still be under warranty by the original manufacturer.

  An "Out of paper" message on the control panel and the all-in-one doesn't pick up paper

  An alphanumeric Code (example: ' 0 x 'r' C2...) ") or 'Ink system failure' Error Message is displayed on the front panel when printing

  To contact HP Technical Support: contact HP worldwide | HP

  Hope this helps,

  Jason

• photosmart 5510 HK copy problem?

  problem copying HK photosmart 5510.  He can't copy the whole a4 page.  lower part is missing.

  Hello thomasylam.

  Try changing your printer is set up for the country.

  Installation - Set country/region and select a country where A4 is the standard paper format and not letter. Europe / UK should work. Then you might be able to select A4 in the size of the destination for the copy feature.

  See you soon!

• HP photosmart 5510 won't print black

  I have a photosmart 5510 which do not print black. All other colors are OK. Have changed cartridge and went through all the steps on the site of diagnosis without success.

  I really need to turn it on. Any ideas gratefully received.

  See you soon.

  Here is a link that can help you with this problem. It can a be a print head.
  http://goo.GL/OTmPV

• Photosmart 5510: customer paper size

  Hello world

  I have never posted on a forum before, but I'm about to have a magma down! I try to print my wedding invitation. they are a custom size of 19.7x13.9 cm., I tried to add the custom paper size by following the instructions on the other posts, but this has not worked. paper/output is missing from the advanced settings.

  help would be greatly appreciated because I alsways bought of HP printers, but if I have to buy a new one for that I won't buy HP I'm worried sick have the same problem.

  Thanks in advance

  Hi @lilrhi,

  Welcome to the HP Forums!

  I see you are trying to print on paper 19.7 x 13.9 cm with your printer HP Photosmart 5510, on Windows 7. And I'm happy to help you!

  According to the specifications of the printer, it is not a supported paper size. The paper sizes supported for this printer are:

  Type of paper

• Photosmart 5510: Out of warranty 5510 won't print black

  My Photosmart 5510 off-warranty will not be printed in black and color blocks on the test page are weak and upholstered.  I have responded to customer cleaning tips with no improvement.  Not enough messages about the problem detail advise to proceed.  What to do next?

  Greetings @HLDLC,

• HP Photosmart 5510 'Printer offline' show

  To the right,.
  
  I started having a problem with my HP Photosmart 5510 - running on a Mac OS x 10.6.8 computer wirelessy.
  
  Until yesterday, I was able to print wireless towards her, even when he was asleep he wakes up and print.
  
  Now, however, I get a "Printer offline" message whenever I try to print what he's awake or not and I have to turn on the printer and on again before it prints.
  
  My printer HP utility can see the printer and it is connected to my network.
  
  Any help would be appreciated,
  Thank you
  Ronan

  I found this on the Apache site:

  "You unexpectedly see an Apache HTTP Server installation page when you visit a Web site. If you sent us mail because you have seen a page saying "it worked!" (or something similar indicating that Apache has been installed) on your screen or a Web site you have visited, please go back and READ the page. It must also specify what happens. The page is the equivalent of a demo or the Readme file from a Windows installation of the application; It is intended for the person who has installed the software and is supposed to show that the installation has been completed successfully. The problem you are experiencing has nothing to do with us, and we cannot help you. You must contact the webmaster of the site. If the site is www.foo.com, for example, try to send mail to . If it is www.toddsbeer.org, send an email to . And so on. »

  I think that there is something funny, with (probably your DNS of ISP) your router's DNS settings.  You can enter the configuration of the router and change the google DNS or OpenDNS DNS?

• HP photosmart 5510: hp photosmart 5510

  I have trouble scanning photosmart 5510 on my PC since I installed windows 10: there is no problem with the software, but pinter them cannot see the PC

  Hello

  try to install the most recent to win 10 S/w

  http://ftp.HP.com/pub/softlib/software12/COL39102/MP-108875-4/PS5510_1315-1.exe

• This issue is still pending. My PhotoSmart 5510 continues to go offline during the generation of printed documents.

  I have a PhotoSmart 5510 and a Toshiba i7 Quad 4 laptop running Windows7 with a Trendnet Wireless router.

  My PhotoSmart 5510 disconnects when printing is generated.    All systems are go: online wirelessly connected wireless, does not not offline, set as the default printer, checkmark, etc..  Sometimes it will make an impression and disconnect and sometimes it will disconnect the first time and will not be printed.

  If I run the diagnostic utility I can usually get it online.  But the said diagnostic utility it is disconnected and the problem is not "resolved".

  It also has a problem with the USB.  If I've set up as a USB printer will crash the entire operating system and laptop computer will not restart unless the USB is disconnected or if the printer is turned off.  This does not happen with my laptop computer on the same Lexmark printer.

  obewan,

  This article should help to keep the Wi - Fi connection (including things like setting a static IP address for your printer to avoid the crash between you OS/router/printer):
  http://support.HP.com/us-en/document/c02817031

  Give the steps described a try and tell us if it helps.

  Good luck!

• Photosmart 5510 - wireless Mac - printer offline

  Hi there, I am trying to print from a Mac again photosmart 5510, wireless is connected, tested printing via an ipad - runs like a dream.  Unable to print message error "printer is off-line" laptop (Mac 10.7.2), the printer is not connected.  Printed with a cable but I can't via wifi. Have checked all troubleshooting tips, no luck.  advice is appreciated

  Download and install this: http://support.apple.com/kb/DL907

  Reset the printing system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• an I can cushion of wireless photosmart 5510?

  can I an I Pad wireless connection with photosmart 5510?

  No, you cannot connect to this printer (or the most current HP printers) directly on an iPad without a wireless router.

  If the router is n it is backwards compatible to g.  If it is g, well, then this is g.

• Photosmart 5510: photosmart 5510 doesn't scan

  My Photosmart 5510 left scanning for computer (HP Pavilion with wireless connection). I get a msg of unsuccessful scan from the printer and an HP 5510d series is not found msg on my computer.  He still won't print.     I restarted everything.   When I opened the printer from start I get a box Priinter configuration and software with connect a new printer and add more software options.   A ran the full feature software and driver and get msg that I need to insert the disc and the earlier version cannot be deleted.   Ran print and scan doctor and it says Installer get full software not installed.  I don't know what else to try.

  Hi @dmorfy,

  There is a utility called Microsoft mount it that might be able to help to uninstall the old version of the HP Photosmart from your PC software. It is pretty Strait before running.

  Once it's done try to reinstall the software.

  Please let me know how it goes.

  Thank you!