Problem in Ethernet adapter R61 7733-A46

Similar Questions

• My USB to ethernet adapter works only if plugged into my MacBook Pro. I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports! Any suggestions?

  My USB to ethernet adapter works only if plugged into my MacBook Pro.

  I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports!

  Any suggestions?

  Juice what 'expander' did you use?

  What model of MacBook Pro?

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Ethernet adapter does not

  I can't get the hang of lightning Gigabit Ethernet Adapter (MD463LL/A) working on my Macbook Pro 15 inch 2014 (11.2).

  When I plug the unit in each port thunderbolt I don't see anything on the screen. However, when I look in the section "Thunderbolt" in system information, I see the following:

  

  When I look in Network preferences, I don't see anything:

  

  And when I try to add a new network interface, ethernet Thunderbolt is not listed:

  

  I searched around for this problem, and some have recommended the removal of all interfaces, killing the networkpreferences plist and restart. I tried this, and it did not help.

  Also, I went back the dongle assuming that I just got a bad copy and bought a new one. The same problem.

  Any ideas would be very appreciated.

  Did you turn off wifi and move the Thunder bolt to the top of the list. Set to zero if necessary

• Equium P200: realtek ethernet adapter Linux installation error

  I have an old Equium P200 - 1Ed, who started to play up.

  When I try to install Linux, it gives me an error for realtek ethernet adapter and I studied the problem on the forums.

  Apparently, my hard drive is old and decrepit.

  I tried to reinstall Vista from the default Toshiba CD, just out of curiosity, and installed fine, except, seemed unwilling to connect internet.

  Tried Linux, but still the same problem from realtek.

  Apparently I can download the driver bios flash and try to reinstall the bios... it looks like my last hope.

  Anyone know where I can get the bios driver for P200-1ED?

  Updates to the BIOS, you can find on toshiba BIOS support page - http://eu.computers.toshiba-europe.com/innovation/download_bios.jsp

  To be honest I don't know if the BIOS update will help with the installation of Linux, but you can try it.

• Satellite L770 - ethernet adapter has stopped working

  Hello
  I have three laptops all connectable to my home hub, but I seem to have serious problems with the latest model, L770-13D. The signal strength has never been as good as the older models, and most recently the Ethernet adapter has stopped working. I have updated drivers on the two adapters, but it did make a difference. I recently updated my connection and I wonder if the Ethernet adapter is not configured correctly because it was working fine before the upgrade.

  I also tried almost all the tests I can do - Toshiba config doctor returned a FAILURE on the verification of the material that I did, but the device manager says that the two network cards work OK. Also, troubleshooting reports wireless adapter that it "can be a problem", the evidence seems to be directed towards a hardware problem with this laptop.

  Any thoughts?

  Have you noticed this Ethernet problem on the first day? Otherwise, I recommend you to reinstall the OS using original recovery image and test once more with the factory settings. Recovery image contains the drivers right and tested. It is also configured to be used immediately after the first start, so it shouldn't be a problem.

  Have you ever done this?

• Thunderbolt to Gigabit Ethernet adapter not working

  Hello

  I'm new to this community has never had a problem on my mac since I had last year.  MacBook Pro retina mi 2014 running El captain.

  My ethernet is not picking up DHCP and thunderbolt ethernet does not appear in the network interface.

  I use also fell in love with VGA Converter works on the two test port.

  I also reset the PRAM and the MSC still nothing.  Also restored some peripheral preference to another forum I found on the internet.

  I created another account from administrator to test to see if the interface resumes, still nothing.  How ever wifi works without problem

  Thanks in advance if anyone could help with my problem.

  Dump of information systems presents its collection as below.

  Bolt of lightning to Gigabit Ethernet Adapter:

  Name of seller: Apple Inc..

  Device name: Thunderbolt to Gigabit Ethernet Adapter

  Vendor ID: 0 x 1

  Device ID: 0 x 8003

  Revision of the device: 0x1

  UID: 0X0001000203A8FCF0

  Apple serial number: DTN450706APDWKHBZ

  Route of chain: 1

  Firmware Version: 5.5

  Port (upstream):

  Status: Connected device

  Link status: 0x2

  Speed: up to 10 Gb/s x 1

  Port Micro Firmware Version: 0.0.8

  I have this problem as well. My crush to the ethernet adapter was working yesterday, but now I have not been able to run all day. I even tried everything said in this thread: ImtiazThunderbolt Ethernet does not work after upgrade to Yosemite , you should try what is in the thread, as it has worked for some people.

• Satellite C665 - Ethernet adapter has stopped working

  Hello
  A few weeks ago, I noticed that the ethernet adapter has stopped working. It has disappeared from the Device Manager, and I can only access internet by wifi.

  When I turn off wifi and connect the ethernet cable (which connects to the modem) nothing works.
  I tried to restore the windows settings, but that didn't work.

  Can someone help me?

  It is possible that the LAN module is defective.
  All you can do now is to check and install the original recovery image and check the functionality with the factory settings. If the problem persists it is definitely hardware problem.

  I think that it is not worth to fix it if you can continue to work with WLAN connectivity.
  What do you think of this?

• Use of the USB to Ethernet adapter to find cRIO Systems

  Hi all

  I'm trying to connect to one OR cRIO-9066 to my laptop using USB-to-Ethernet adapter.  But I have a problem with it; Find VI systems shows no results unlike the direct connection via the ethernet port on the laptop.  I wish that the connection of the USB-to-Ethernet adapter to support this feature as well.  I would like to know if somebody did, and I hope a solution to this.

  Here's my setup. I bought the adapter USB-to-Ethernet of RadioShack. I connect the adapter to a USB port on my laptop. The adapter is the female Ethernet port on the other end. I directly connect cRIO and the adapter using a crossover ethernet cable. What is of note is that ethernet connection works.  I can specify the IP address of the cRIO then I can communicate with crio in the same configuration. However, finding systems VI cannot find any system.  LabVIEW 2015, is what I use.

  Instead of using the adapter, if I use a direct connection via the ethernet port on the laptop, find systems VI works fine.

  Any help or suggestion is appreciated.

  Thank you in advance.

  After all, my conclusion to this problem has been the model of Ethernet USB card I was using was not good.

  Gigaware USB to adapter Ethernet (from Radio Shack) was working not with find systems VI on my environment even though it is still able to connect to CRIO if I know the IP address. I even had the other, but the result was the same.  The solution for me was to use another model of the BADGE, which is NS-PU98505. It is cheaper, but has worked with find systems VI.

  I don't know what's behind the different behaviour, but the issue is resolved on my end for now.

  Thank you all for all the tips and ideas. Congratulations to all!

• Intermittent problem Realtek ethernet driver

  I have an office p6703w Pavilion with Windows 7hp, Realtek PCIe FE Family Controller.  Just got a new integrated modem/router to Comcast.  Wi - fi works very well on all devices.  Wired connection works fine on my laptop. Wired connection on the desktop shuts down intermittently for 3-5 seconds and then comes back.  You can see cycling on the icon.  It happens both when opening a new site or when it is idle.  Tried other cable, ports, etc. and almost excluded from each variable.  Latest version of the driver is installed, diagnosis say it works very well.  Any help would be appreciated, thanks.

  Hello

  The USB/ethernet adapter works without problem.  I never got to the root of the problem driver Realtek.  Thanks for your help.

• F5D5050 USB 10/100 Ethernet adapter Belkin for Windows 7

  I have windows 7 and I checked the comparability on the Microsoft Web site and it says that the F5D5050 USB 10/100 Ethernet Adapter is compatible but when I plug it in, I get an error message that the Broadcom Bluetooth 2.1 + EDR USB device has a driver problem.

  Anyone had luck to get this product to work on windows? Does anyone have an idea how to operate?

  It was the procedure to install it on Vista http://www.belkin.com/support/article/?lid=en&pid=F5D5050&aid=4404&scid=220

  It does not have Windows 7 drivers and looks like it is be misidentified.

  You can get more help on the Windows 7 forum.

• D-Link DUB-E100 high speed USB 2.0 Fast Ethernet Adapter

  I have a problem with my LAN card when I come overseas for a business meeting. I choose not to send my new phone Samsung difficulty since it is necessary for a meeting. So, I bought this adapter for temporary. It took me an hour to make it work on my Windows 7 with WinXP driver (there is no Win 7 drivers available). I found it works well if I use only for my Microsoft Outlook, but not at all for the Web site. Most of the time I try to surf, my system crash and blue screen appear. Any people have any idea what should I do? I have to be on this thing for months and I have so much to do between this computer and my office.

  Why can't you buy something that is Wondows 7 compatible? The DUB E100 is also old

  On the site of D-Link...

  «The D-Link DUB-E100 is a Hi-Speed USB 2.0 10/100Mbps Fast Ethernet Adapter specifically designed to plug into a port Universal Serial Bus (USB) available on a computer desktop or laptop PC running Microsoft Windows XP, Me, 2000, or 98SE.»

• So, updated for Win 7. Clean install. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Clean install. 2 problems. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Probably you run first win7 Upgrade Advisor, who did you would probably show your system as not supported under win7

• Best for PC to Macbook Pro Ethernet adapter to transfer files

  Hello

  I was looking for a straight answer to this question. I am a new Mac user (Woo hoo) and I need to transfer my files from a PC to my new Macbook pro. Which is the best ethernet adapter (if this is important) do so... a USB adapter or the adapter thunderbolt?

  I thought I read that love at first sight was the fastest, but then I read that I might have a question of transfer to a PC.

  Thanks in advance!

  The best ethernet adapter's ethernet cable connecting ports ethernet on both computers.

  There is no need to bother with love at first sight or USB to do this.

• HP DL180 Gen9 server: HP 10 GB 2 port 561T Ethernet adapter

  Hello

  Can you help me if this 561T HP 10 GB 2 Port Ethernet adapter is Compatible with my HP DL180 Gen9 Server?

  Thank you

  Mark

  Hello

  This compatible list does not DL 180, but it is compatible with many other DL Gen8 servers:

  http://h20564.www2.HPE.com/hpsc/doc/public/display?docid=emr_na-c03909467

  It must be. But my suggestion: talk with representatives of HP in your region drirectly, they are ready to help you.

  Kind regards.

• Cannot install Ethernet adapter integrated into my 300 S1700

  Hi guys,.

  I reinstalled my S1700-300 Satellite with W2K Pro. At the back of the laptop, it is possible to connect an ethernet cable, left for the modem, labeled plugin with "Ether". But Win2k is not able to find the ethernet adapter, do you know what to do or do you know where to find the driver of fitting for her?
  I also looked at the manual provided to Toshiba, but for this model nr. There is no information on an ethernet card, but I'm sure that on mine is a.

  Thank you
  Babsi

  Hi Babsi

  Please go to http://eu.computers.toshiba-europe.com. Under Support & downloads, you can find download drivers. Select your type of machine, OS and driver. There you can find driver LAN for W2K.

  Good bye