RAM test

Similar Questions

• My Satellite A110-180 always do a RAM test

  Hello.

  I can't allow a quick start (start without the RAM test) in my cell A110-180. I upgraded my RAM from 1 GB to 3 GB and I would like to disable the standard ram test when the laptop starts up because now becomes very slow. I've updated the original Bios HTW20 V1.30 for Bios HTW20 V2.00 but in the new does not have this option either.

  Can you help me?.

  Thanks in advance.

  > I upgraded my RAM from 1 GB to 3 GB and I would like to disable the standard ram test when the laptop starts up because now becomes very slow.
  How does something like this happen?
  After RAM upgrade boot is actually not different as before. Portable operations are faster.

  Can you please tell us which module RAM do you have used for the upgrade?
  I checked the laptop computer's specification and memory modules compatible RAM for your Satellite A110 are:
  1 GB-PA3411U-1M1G
  2GB - PA3513U-1M2G

• BIOME-1 error when you run the diagnostic material for RAM test

  In recent months I've known several blue screen errors during startup. Initailly, initially, I thought that maybe it's a hardware error, but after running Diagnostics of material (press F9 to start) and have all the tests passed so I assumed it was a software problem, I focused my attention on that. However, today, I started to run hardware diagnostics and I discovered that I had a RAM issue with the BIOME-1 error code. Is it possible that the hardware diagnostics can not full capture errors and that a RAM issue was first the cause of blue screen errors?

  I called HP support and they sent an engineer to the bottom. After you open the computer case, the cause of the problem has been established as a RAM module that was not properly secured. After getting the RAM module, the blue screen errors did not reappear again. The engineer also ran some tests and confirmed that everything was fine.

• S205 RAM/memory Test

  I was playing with my Ideapad S205 last week and found a place that allow me to make some sort of memory/RAM Test. I can't find a reason any. I checked the BIOS and other startup options, but I can't find it. Does anyone know what I mean? Where to find it?

  Thank you.

  Hello, CNMC

  The BIOS of S205 netbook has no memory test option.

  If you are using Windows 7, you can run "Memory diagnostic tool"

  Please refer to the cited web link below.

  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-memory-problems-on-your-computer

  Best regards

  Tanuj

• Upgrading RAM gives the Blue error screen.

  Original title: tried to grade until my memorey: 256 MB in the two slots to 2 1gigs RAM but keeps giving me a blue screen

  can anyone help im using a dell dimension de051 cpu 2'53 ghz intelceleron had 2 256 MB of ram installed ddr I tried up to grade 2 1 GB ram memory, I checked to ensure that it was compatible when I install 1 gig of his fine, but when I add the other happens with memory has changed that I want to go to boot options when I connect normally get help from the blue screen

  Well the upgrade: 256 MB to 2 GB will show a big improvement in overall

  applications. However, ram stick must be installed either with 1 or 2 faces

  chips on the module, mixing them creates incompatibility. If all have the same

  type, and then mix them up is fine, old and new, is not serious. However, the different

  sticks of size according to the Board of Directors (256 MB for slot 3 & 4, 1 GB for 1 & 2), some old maps

  requires it for optimal performance...

  If above is true, then install ram sticks 1 at a time, may be running microsoft ram Tester

  to see a problem. Reach: http://oca.microsoft.com/en/windiag.asp

• restore the firmware for macbook pro 13 mid 2009

  Hi all! This is my first time using the support community so forgive me for any rudeness and English summary.

  I recently bought a used mid 2009 macbook pro 13 "with no disc on this subject, I installed a new empty 120 GB ssd drive.

  I asked a friend and he has downloaded and made me a usb bootable with osx on it (lion). I instaled the osx and got the macbook running successfully and it was perfect.

  I decide to update and went up el capitan wich sucessfully installed. After the update I tried it out, web navigation simple, when suddenly, out of nowhere the mac stop (much battery left and the led indicator to confirm) and has not started since... when I turn it on the led light flashes and it gives the s.o.s. beep (3 short beeps followed by 3 long beeps and then 3 short beeps) the optical drive made his usual looking noises of boot and the fan continues to spinning, I tried to remove the battery 10 minutes several times and nothing... I read a lot about the problems of ram tested with one stick at a time in the two slots and no improvement... bought a new pair of hynix 2 gb 1066 mhz pc3-8500 ddr3 sticks as recommended for this model and replaced the "old"... did nothing.

  I have no original discs just the macbook itself and the charger. Also tried to boot from the usb drive... not good... tried to start mode revovery... nothing that the black screen and a beep sounds.

  I did some research and read a looooot online and in discussions such as this apple and found it to be the sound warning for bad/corrupted efi rom (as opposed to the majority of people declaring it to be a ram issue) which needs to be restored or flashed... However, apple does not provide or at least I can't find a picture of recovery for my model cd special I know it's the macbook 5.1 (a1278 / emc2254). Is there any solution for this? Please help in some way that you can welcome suggestions!

  Thank you

  Then, you say at the end of your post, you say that it is a MacBook, but it is a MacBook Pro. Check which model you have.

  On the updates of the EFI and SMC firmware for Mac computers with Intel processor - https://support.apple.com/HT201518

  What to do with all these "beeps mean at the start? - http://forum.insanelymac.com/lofiversion/index.php/t62919.html

  Power on self-test beep definition - part 2 - http://support.apple.com/kb/HT1547 - old Macs

  Mac Power on Self Test RAM Intel processor error codes - http://support.apple.com/kb/HT2341

  iMac (mid 2007) and later models: on startup tones - http://support.apple.com/kb/HT2538

• kernel [0]: disk0s2: i/o error and AHT freeze on 27 "iMac

  Hi all

  According to the title, I have serious problems with my iMac 27 "with El Capitan.

  It started all of a sudden with wheel rotation in a way that I am still unable to reproduce.

  I have not installed anything again for weeks. Enough I traveled a lot for business, so my iMac has been mostly off.

  The logs show a recurring kernel [0]: disk0s2: i/o error.

  Initially, I tried a repair disk that consistently failed, so I tried AHT, once to short and long.

  They both finished in a gel semi then very close to completion.

  I'm talking about gel semi as mouse reacted but with seconds behind and jerks and stop button has not actually no result so he needed a hard stop.

  I also tried to leave the long test running overnight to prevent my impatience for her give up too soon.

  The next day, I found it hung there, very close to realization.

  Not sure if it's relevant information, but the only way to get my iMac on the way of the AHT was pressing command + D and the iMac sarched necessary information on the net.

  THE D only has not given any results.

  I decided to enter recovery mode, format and reinstall El Capitan.

  Everything went well and that the system worked very well.
  I opened Safari and scoured Internet. Everything seemed very well answered.

  Then I turned off the system as another business trip is expected.

  3 days later, I rebooted my machine and still ONCE, spinning drying up and disk0s2: error e/s in the newspapers.

  Repair disk fills very well this time (Foundation nothing to fix) but same thing AHT: semi freezes almost to the end.

  As a bonus, I now get a system that is very slow to restart: it takes 10 minutes to show me the office and there is in fact the largest part of 10 minutes for the gray Apple with a progress bar that seems to never end.

  Then at some point it ends and I can connect, but connection takes at least 2 minutes.

  Saw that AHT is a RAM test and a test of logic board before freezing, but I don't know when exactly it freezes because it does not end and I have no error reported trials.

  Now, the question is: are these symptoms more of a HARD drive or a logic board failure?

  
  

  I apologize in advance for my mistakes and spelling errors, it should be obvious English is not my main language.

  Thank you very much.

  Probably a fault bad cable/connection between the logic and HARD drive, hard drive external pension, pension bad logic in that order.

  Make an appointment with a genius at your nearest Apple Store. Diagnosis is free and they'll give you a quote for repair.

  If you are on a budget to replace a HARD drive in an iMac is pretty simple DIY job provided you watch YouTube videos and get the right tools.

  C.

• Flashing black screen with - after post "fix."

  -flashing at the start (Simplified) mark no restore needed.

  Only f2 and f12 not work 0 and not f8

  After buying a windows boot cd and try to fix the mbr if bootrec and chkdsk and repair windows, I got that chance didn't so that never (waste of money). I even tried to delete the keyboard key thing I was stuck and the withdrawal / ram test with no luck what so ever. then decides to Flash the bios and the n t work I had no backup office and refused to lose everything then there even when we begin I decided to download ultimate boot cd to ultimatebootcd.com (its free lots of programs)

  1. using another computer download and burn the file to ultimate boot-cd.iso (make sure you use an iso burner and burn and 10 x or below sub form of image and data are checked.

  2. Start computer press f2 to enter the bios and change the boot order to cdrom, boots first. Press ENTER to boot from the cd and let the program startup.

  3. in menu cd boot chose press down to the HARD disk, and then press ENTER.

  4. press on toward down to the Startup Manager and then choose special fdsk (this command won t repair work on windows at the moment that s why using the disc.

  5 choose the partitioning tool (you can get a mistake just press on enter)

  6. new screen marked hdd1 or hdd2 according to hard drive.

  7. Select the partition with the highest Go list (may have a heart next to it or be marked hidden press ENTER.

  8 red screen options chose to set the partition as active and press ENTER. (follow the orders of the screen for saveing and restart.

  9 restart the computer remove disk, then press f8 and choose repair windows (you have this option now)
  try to let the computer automatically repair it may restart several times.

  10. now enter prompt to repair windows and type.
  Enter the letter of your ex partition type then
  Bootrec/MBR press on enter
  Bootrec /fixboot press on enter
  Bootrec /rebuildbcd press on enter
  Chkdsk r - press on enter (ignore code 50)
  Chkdsk f - press on enter (ignore code 50)

  11 restart the computer should boot properly.
  (if you get a blue Ref lash bios windows loading screen to clear a questions)
  My computer is running now on windows vista and I n t lose a single file.
  a court boot sector mark the partition hidden or inactive and that s how to fix without restoring your windows and losing everything you have if you n t have back up the drive.

  Thank you for your detailed report.
  Out of curiosity, do you have for Toshiba laptop?

• Satellite U400-10N fails to start all by showing a black screen!

  So, I press the power button, the 3 LEDS are fuctional appearing but CPU - GPU fan does not start!

  After a while, it shuts it self and then he tries to start again, but the fan fails again while the power led and not others (Led 1 and 2 down).
  Must say once again that the screen always appear black (maybe also dead)

  I thought it was a problem of overheating, so I cleaned the fan but with not a lot of dust!
  But it was not the problem crearly because I tested it!
  Now I think that this could be a GPU problem, but I don't know about you!

  Any suggestions that he could be and how o solve this problem? Thank you!

  Hello

  It may be RAM problem, it may be a motherboard problem, it can also be a problem of CPU or GPU.
  Any party may be affected.
  So what to do?

  You can see the part as RAM. You could buy new Rams tested and could replace it but what happens if you buy new RAM modules, replace it and laptop will NOT turn on?
  You would spend the money for the new RAM but eventually the other party could be faulty

  So I think that a professional technician must check the unit first.
  Guys could give you an answer as to the defective part and then you could decide what to do
  You know what I mean?

• Tecra A7 PTA71E - Win XP BSOD

  Hello

  Since 2007, I have my Tecra. I bought it with win XP. Until the middle of 2011 OS works OK, but not later.

  When I turned toward the top of the computer, it starts and when the Office was running, I just started with the trackpad or USB mouse on any item on the desktop, but he could not close more. I could only use of the keyboard and the selection of logoff windows blue screen n to log in again.

  From that moment, I could turn on or off each application or component on the desktop.
  The problem with Windows XP.

  Unfortunately, after replacing the windows 7 32 bit with a previous disk formatting problem remained.

  Now, do not turn off your single computer switch to hibernation. Each full stop ends the same, and I have to log off and log in. Mouse USB and touch pad work the same way. It makes no difference if the mouse is connected or not.

  Hello

  It seems that the problem of equipment.
  I came to this conclusion because the installation of the new operating system (Win 7) has not helped to solve this problem.
  So I think that you agree with me.

  What part of the material could be affected?
  Well, I think that some common parts such as RAM or HARD disk should be tested.
  How?

  Well, the HARD disk might be tested using some freeware like Drive Fitness Test Tools.

  Software RAM tests are not really useful, and I believe that laptop must be tested using new modules of good work.
  But of course it s just a guess on my part

  If you put t want money spent on the new RAM modules to check if its ok or not, consult a technician who could do it for you.

• The subsequent update (10.11.4) kernel panic

  After the installation of 11.4, I got a kernel panic in the very early phase of startup. Recovery disc reinstall OS X did not help. Secure boot has failed. No newspaper that I could find. I went back to 11.3 from a backup, but is there any thought on how to diagnose / troubleshoot? I have tried disk first aid, nothing helps.

  It is a Mac Pro mid-2010 system, using an SSD for boot and a physical backup drive, both encrypted. 11.4 does not, because of 11.3. No problem for RAM (use a RAM tester). Everything tests OK.

  Send a copy of the kernel image.

• Satellite A660 - 10 X - freezes several times

  Hello

  A few months ago I bought the Satellite A660-10 x. On installed original system it freezes once (I used laptop maybe an hour) but I thought it was an accident, or maybe something was misconfigured. Then I installed the clear disk from Microsoft (Windows 7 Home Premium) system and install only the necessary drivers, but the problem from happening again. At first I thought as this only, when I don't click or move the mouse for over 1 minute, but that for now the problem appears also when I click or write something. I very rarely use this laptop, but as you can imagine it is very annoying and it is that I can not trust this laptop computer and the data on it. Maybe you know what are the causes of the problem or maybe some new drivers have been released to remove this problem?

  I read that not only I have the same problem.

  Best regards

  Hello

  You are using the latest driver for the Toshiba page graphics card?
  Please do
  In addition new BIOS version just came out too much it is s BIOS update!

  In addition, you can run some RAM tests using the free tools like memtest86 + or similar.

• Satellite Pro 4600 very unstable and BSOD

  Hello

  I have a Satellite Pro 4600 c750/128 with xp installed.
  It was ok, but slow, so I've updated at 500 MB of memory.

  He now became unstable under windows and throw a screen blue after awhile, which is a related, but firm and we will restart until I have a chance to read the error message.

  I tested the new memory from one day to the next with memtest and run 4 passes all tests without error, about 9 hours of operation (on the back).

  The event log indicates a discharge, but this does not mean a lot to me.
  The event log has an error during startup, what was there before the memory upgrade.
  Googling Sugest a fix to update the bios, it's always available for this laptop bios?

  The BIOS should be available for this former Satellite Pro 4600.
  The BIOS and drivers must be placed on the page of European driver of Toshiba.
  Here, you will need to search the Archives!

  But I doubt that the error is caused by the BIOS.
  Is the laptop ran stable also with the previous BIOS and it foolish to update the BIOS to fix this problem.
  I'm sure it won't change anything!

  Upgrade the RAM and BSOD appears now.
  I think that the problem is related to the RAM, even if the ram test didn't find any errors
  The RAM may be not compatible also if no error has been detected.

  I recommend that you test the laptop without the new RAM and check if the BSOD will appear again.

• Portege Z10T keep restarting

  Hello

  We have a few tablets of Z10T, they are always reboot with DPC_WATCHDOG_VIOLATION.
  We have changed the motherboard and RAM tested. I will give the result to memory dump file.

  Please tell us why this continue to happen.
  Says memory dump file: igdkmd64.sys readers is a problem, but we have checked on the Toshiba support site and the Intel support site. graphic tablet drivers are up-to-date.

  Here is the result of dump:

  ERROR: Module load completed but symbols can be loaded for igdkmd64.sys
  ERROR: Module load completed but symbols can be loaded for dlkmd.sys
  Probably caused by: igdkmd64.sys (igdkmd64 + 6393f)

  Follow-up: MachineOwner

  1: kd >! analyze - v

  Analysis of error checking

  DPC_WATCHDOG_VIOLATION (133)
  The CPD watchdog detected an extended operation to an IRQL of DISPATCH_LEVEL level
  or higher.
  Arguments:
  Arg1: 0000000000000000, just a DPC or ISR exceeded his time d. Delinquency
  component may generally be identified with a stack trace.
  Arg2: 0000000000000501, DPC time (in ticks) count.
  Arg3: 0000000000000500, DPC time of bids (ticks).
  Arg4: 0000000000000000

  Debugging information:

  OVERLAPPED_MODULE: Address regions for 'condrv' and 'tunnel.sys' overlap
  DPC_TIMEOUT_TYPE: SINGLE_DPC_TIMEOUT_EXCEEDED
  DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
  BUGCHECK_STR: 0 X 133
  Nom_processus: System
  CURRENT_IRQL: d
  ANALYSIS_VERSION: 6.3.9600.17298 (debuggers (dbg). 141024-1500) amd64fre
  LAST_CONTROL_TRANSFER: from fffff80162a0a3c8 to fffff801629cdaa0
  STACK_COMMAND: kb
  FOLLOWUP_IP:
  Igdkmd64 + 6393f
  fffff800'b2c8893f eb06 jmp igdkmd64 + 0 x 63947 (fffff800'b2c88947)
  SYMBOL_STACK_INDEX: 8
  SYMBOL_NAME: igdkmd64 + 6393f
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: igdkmd64
  Nom_image: igdkmd64.sys
  DEBUG_FLR_IMAGE_TIMESTAMP: 526eddae
  FAILURE_BUCKET_ID: 0x133_DPC_igdkmd64 + 6393f
  BUCKET_ID: 0x133_DPC_igdkmd64 + 6393f
  ANALYSIS_SOURCE: KM
  FAILURE_ID_HASH_STRING: km:0x133_dpc_igdkmd64 + 6393f
  FAILURE_ID_HASH: {3723beb4-0ab8-f99b-e05f-eeaf7db55d72}

  Note: these use Tablet Targus DisplayLink Docking Station but sometimes I found Tablet reboot without connect to it.

  Thank you
  Jean Charles

  I can't say for sure why this BSOD error pops up, but according to Microsoft knowledgebase article the question of the DPC_WATCHDOG_VIOLATION occurs when the DPC routines one or several drivers exceed the CPD Watchdog time-out.

  Purge details mention igdkmd64.sys file.
  As far as I know that the gdkmd64.sys could be the Intel Graphics driver.

  Probably the Intel driver causes this problem.
  It could also be the processor that supports the graphics unit causes this problem.

  Sorry, but all the pieces of equipment must be checked to provide detailed diagnosis.

• Tecra S5 - endless beeps and start-up

  Hello

  I have a strange problem:

  Start button / stop
  Beeps without end
  Start screen offers operating system, only Vista Business installed.
  Also offers the RAM test.

  I did the normal and the RAM test extended, without any error. I push the load Vista option and it loads.

  It seems then that the cycle screen all the icons in the task bars. I can't start anything via the quick launch or a tray. Once I loaded any program office all settled and I can use the phone normally.

  Restart or turn on will cause the same behavior.

  I looked at the various newspapers and nothing is displayed on the POST or system failures.

  Can someone point me in a direction where I can start looking?

  Hello

  Beep codes usually occur if the motherboard does not work correctly or if there are some problems.
  In most cases, a beep is displayed if the motherboard is ok and the MESSAGE could be passed correctly.

  But if there's some beep codes at the beginning of the boot order, then this would mean that an error has been detected.

  See this page for more details on the different beep codes:
  http://www.PowerOnSelfTest.com/Post4.htm

  Perhaps, it might be useful.