Re: People do not recognize the answers

Similar Questions

• PCMCIA card does not recognize the connection to the local network on Satellite Pro 4340

  Hello world

  I have 2 Satellite Pro 4340, running Win2K, SP4. I bought a card PCMCIA 10 / 100MB of Ultron (more or less no name :-))

  When you insert the card, Win2k recognizes the card, but when the I plug the network cable, it does not recognize the connection. Cable is fine. It seems there is no power on the PCMCIA card. I read on some forums that there is a problem with the Topic100 Card Bus driver and voltage. I see that many people have the problem but not where to find the driver for the problem :-/ I couldn't find a driver on toshiba support site. A

  ll have an idea, or better a link where I can download this driver? Any help is appreciated and thanks in advance for your help, support and answers.
  Corey

  If this card needs a driver you will not find it on the download page of manufacturer of portable. You must check the card producer site.

  As you know in the world of computers, it has set different standards. Produced very often cheap are not designed for these standards, and you can have different problems. I recommend you to use high quality products.

• Fingerprint utility does not recognize the password website - Satellite U400

  Problems with the password Bank (TrueSuite Access Manager, 2.5.29.0 latest version;) Vista); Utility does not work, does not recognize the Web site password entry, doesn't react at all. Tried it in IE8 and Opera 10, tried to reinstall Truesuite Access Manager. The fingerprint login works fine, very well file protection works.

  Someone at - it the same problem? Any ideas on a solution?

  Thank you.

  Thanks for the comments.
  If you have questions try to find answer using the advanced search options.
  In this forum, you'll find helpful advice a lot or comments about so many different issues with Toshiba laptops.

• DreamColor LP2480zx does not recognize the USB for calibration

  Hello

  I have a DreamColor LP2480zx, which does not recognize the USB connection to the computer during calibration.  I have my eye HP connected through this monitor, so I know the connection and the cable is good and mouse, keyboard.  My setup is like this:

  Reference Dell 690 running 64 bit + Windows XP

  DreamColor LP2480zx

  Apple Cinema Display 23 "

  I bought the DreamColor used, and in all other respects, it seems to work very well.  The original owner didn't have it calibrated within a certain time, but said that having had no problem with the previous calibration.  I installed the last APS (version 2.0) and updated to the latest firmware.  These updates produces no change in recognition USB problem.

  The interesting thing is, I was able to calibrate the Apple Cinema Display, using the same configuration of connection (mouse, keyboard, and HP eye connected to the computer via the LP2480zx) APS was able to see the USB connection and this very well calibrated monitor.

  I had trouble with this problem for a few days.  I've looked around quite a bit online and found a few others who have this same problem, but I did not yet find someone who can point out a solution.  If anyone has had this same problem, or has heard of results that correct it, please let me know, because it's very frustrating.

  Thanks for any help

  Clay

  An update to my previous post, I realized a work around for this problem.

  Apparently, this problem has to do with the Dreamcolor screen and/or software APS do not like working with 64 bit systems.  I'm not saying that it is always the case, but I saw the other posts on this problem on 64-bit systems, and I spoke with two other people personally who told me that they also had the same problem, try to calibrate its Dreamcolor monitor when it was attached to a 64-bit system.  HP does not seem to be concerned about this problem, because they do not even recognize its existence, but since I'm far from being the first to report this problem, he's obviously not a one-time problem.

  My solution was this: I had connect the monitor to a regular running XP 32 bit system.  After I did, I could re - calibrate the monitor without the problem of USB connection.  This isn't a very good solution because not everyone has access to several machines, running different operating systems.  But it's a work around, and it worked for me.

  Hope this helps other people who have this same problem with their Dreamcolor monitors hooked to their 64-bit systems.

  Clay

  PS- I posted this as resolved, only because I was able to calibrate my monitor.  It's not really solved the problem, but it gets the monitor working again.  Maybe HP will address this problem in the future, but I'm not holding my breath.

• sync iTunes does not recognize the photo library

  Hello

  I've been messing around with my photo library, and now when I try to sync my iPad, iTunes does not see my photo library.  The Photos app connects to the library, which is located in the folder images for the user account, no problem.  But when I connect the iPad to the iMac and iTunes opens, if I click on the header of Photos on my iPad, sync Photos box is unchecked, and when selected, the option copy photos pictures, looks as the pictures in the folder is empty, when in fact the photo library is located here.  She received no related some how?  I had my library on an external drive and passed to the user account on the internal disk without problem.

  Thank you!

  It is surprising how a simple search does not turn the answer to such a question, which one would think would be quite a common problem.  Indeed, several people asked similar questions, but often with no response.  However, I managed to find the solution on manual site Apple of all places.  And in the interest of the public service will post it here.  The problem is even if I had taken my photo library with the preferences window, I had not designated 'Library system' as in below.

  

  Once the user has clicked on 'Use as system library', then iTunes could see the library.

• Fax does not recognize the incoming fax signal

  Fax does not recognize the incoming fax on Officejet 6700.

  Hey Bills6700,

  Welcome to the HP Forums!

  To not recognize the incoming faxes, I've included the document "cannot send or receive faxes. I know that's not the exact error message you get, but the steps will always help you.

  If you are still having the same problem after troubleshooting, could you please answer the following questions.

  1 is on a dedicated phone line fax machine, or is it shared with another phone?
  2. are you using a separator, or is plugged directly into the phone jack fax line?
  3. the phone cord is plugged you need two wires of copper at the end?
  4. do nothing missing on the fax test report?
  5. do you have an answering machine (physical box), or voicemail (you must call to access your messages)?
  6. What is the rings before answer on?

  Please let me know the results for the troubleshooting steps.

  Thank you.

• Compaq presario cq57-339WM does not recognize the drive as a bootable disk recovery

  Compaq presario cq57-339WM does not recognize the drive as a boot drive recovery, I'm sorry people, I searched and I entered the job in New York as a matter of research. Operating system is 7 Home premium. Hard drive went bad, so I rplaced with new. I have had I have windows image backup, but the wizard could not find the hard drive. I ordered the HP poped the first of the two recovery disks, but the machine does not recognize the drive as a bootable disk recovery. I did factory retrieve records a large number of times on computers with different operating systems and have never seen this. TNA

  Randy Rich

  I found this on PC world. I downloaded everything I need, I hope. I tried not to build the disk again. I need some rest and sleep. Stay tuned for more develonents. Here is the link http://www.pcworld.com/article/2364269/how-to-reinstall-windows-like-a-pro.html?page=2

• HP Solution Center does not recognize the network printer

  Network has a hp 309 a printer, can print from the computer, the problem is:

  HP Solution Center not load-says incomplete installation.  If I plug in the USB cable and let it continue, it sets up a second printer that only works on the USB cable and it still does not recognize the network printer.

  Question how can I get the Hp solution program to reward the network printer.  If I reload the CD, then reinstall the will other people on the network of the problems?

  Resettlement on your machine won't affect only you, no other machines on the network.

• When I go to move file e drive windows does not recognize the format

  ORIGINAL TITLE: files and folders

  running windows xp pro version 2002 service PAC 3, when I go to move the file e disc windows does not recognize the format, already file types are jpeg and php have tried a restore and fix computer center has not helped. Any suggestion or solutions would be appreciated ARTuro_974

  Thanks to all the answers, don't know how, but the problem fixed, have learned a little about pc THANKS AGAIN to all.

• Western Digital WD10EARS internal hard drive Caviar Green 1 TB - my system does not recognize the new drive

  I recently bought a computer Dell 4700 to a friend with Windows XP installed. I've updated the memory to 2 GB and now seeks to install a WD10EARS 1 TB harddrive. The new works of fine memory is not the hard drive. My system does not recognize the new drive. I contacted WD for help and they told me to try diferent rider combinations that were Jumper 1-2 and 5-6, still does not work, I checked the hardware compatibility list and he said he would start uo without modification. This isn't. I would be very greatlyful for any suggestions, to HELP!

  I've had several people tried to help me solve my problem. They were all, I thought, more than I am computer savvy. As time progressed, solutions became more complex. After they all left without resolution I thought and it appeared to me that the simplest solution might be correct. One person had checked. I turned on the computer and when the Dell logo came I pushed the F12 key to open the Dell configuration screen. The drive on which the new drive has been installed has NOT been activated! Duh! I activated the he and the program Acronis recognized and everything went like clockwork after that. Phew! What relief! Thank you for your comments I am just glad that my problem it doesn't require resolution. Are Mod

• New installation of XP PRO sp3 does not recognize the 500 GB HD

  OK, here are the details:

  System: Computer PORTABLE of Acer Aspire 1700 Pent4, 2 GB of RAM, 80GB (3.5 "full-size, trainee) IDE HD [this is the original HD on this laptop of size important which is designed to use disks 3.5" hard].

  Initial situation: Windows XP Pro (SP3 integrated) installed on HDD of 80 GB and works without poblems. BIOS does NOT show the ability of the intern HD in the BIOS screen. BIOS reports only the model and the serial number of the HD, and there is no options to specify the HD type/format (e.g., MLA, etc.)

  Available: Win XP Pro bootable CD slipstreamed with SP3; It is tested and verified work well to install PC or laptop!

  When running XP Pro on a partition internal 80 GB HD, and when I join a brand new WD 500 GB IDE HD via USB, HD is recognized correctly. I can partition and copy data on the HD 500 GB with no problems!

  When I replaced the old 80 GB HD with the new HD 500 GB HD interning on the laptop, I have the following problems:

  1. I can NOT boot into Windows XP Pro (SP3) which was Ghost on the HD 500 GB of the old 80 GB portable HD it recharges, and if I try the console recovery or secure boot, then the laptop restarts also.
  1B. I have Ghost xp partition to 80 GB HD to a piece of spare HD (40 GB) and replaced the 80 GB with the 40 GB HD and was able to start the laptop without problem. So the problem is NOT related ghost!

  2. I can't perform a clean install of Windows XP Pro (SP3 integrated) because Windows XP Setup recognizes the HD 500 GB GB 131 HD. Therefore, the remaining capacity is not recognized.

  3. I can NOT perform the installation of Windows XP pro (SP3 integrated), even if I have previously partition new HD 500 GB by attaching it to a free desktop PC and use Partition Magic, partitioner of Paragon Disk or other partitioning tools. After partitioning prior, when the 500 GB HD is installed on the laptop (as a trainee HD), then win xp installation lists quality HD of GB 131 and lists the existing partitions as corrupt!

  4. Curiously, if I use Knoppix, Debian, Ubuntu or linux boot CD Mint and start the laptop computer with one of these linux distributions, then the linux installer recognize the HD properly during the phase of recognition of material and later during the phase partitioning HD, the linux system to report a full capacity of 500 GB available for partitioning. In addition, when there are partitions, partitioning linux program then lists these partitions properly as well!

  Considering the 4 points and especially MS Windows XP PRO (integrated with SP3, which should recognize HD with sizes exceeding 137 GB limit - from MS says you must be at least XP SP1 to overcome the size 137 GB limit - and that the different distributions of linux can see the full-size HD 500 GB with no problems) which is exactly the problem with Win XP? Why it does not recognize the full capacity? And how to win xp recognizes a 500 GB capacity, if the new HD is attached to the laptop via USB as an external drive when running XP PRO (SP3) of the 80 GB internal HD?

  so... Can anyone sheds light on the issue with Win XP Pro installation on HD 500 GB IDE?

  Nicely,

  LO

  Hi Palcouk and Doc,

  I think that's the final answer!

  Although, there is a mixture of simple to complex responses to the problem at hand, what it all comes down is that there is a significant difference between the installation of Windows XP and Linux installer program. The XP installation program needs help from the BIOS to deal with HD, and if the BIOS does not support, XP not has no facility to remedy the situation. OTOH, most of Linux new kernels rely on the BIOS for a limited number of extended, but communicate directly with the hardware, in this case, with the HD and therefore manages the material accordingly.

  It seems among users of dual-booting (win/linux) using old PCs, it is a matter of very pretty. What they end up doing is using the first 137 GB that is seen by the BIOS without problem for XP (either as a single partition or divided into several partitions), and the rest of the space is used for Linux because linux has no problem.

  I guess that it really nails the problem with my laptop to a BIOS NON-lba-48-bit!

  Then close this thread as answered or matter who has more to say about this?

  LO

  P.S.: It was very nice meeting you fellows and appreciate all the help and tech expertise.

• Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

  Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

  The duplicate thread information:

  Cannot connect Epson scanner/Nikon camera to printer!

  Hi Carolyn has Culp,

  
  Thanks for asking this question to Microsoft Community!
  
  I understand that your scanner and Nikon camera is not getting recognized in windows vista.

  He would be grateful if you could answer these questions. This will help us to a better way to get a resolution of the issue.
  1. have you made changes on the computer before this problem?
  2. What is the brand and model of the scanner?
  3. are you an error message or error code?
  4. is that your other USB devices work?
  I would suggest trying the following methods and check if it helps.

  Method 1:
  

  Try connecting to another USB port and check if the camera is detected or try to plug the camera on another computer.
  Method 2:
   
  Hardware devices do not work or are not detected in Windows: http://support.microsoft.com/mats/hardware_device_problems/en-us
  Method 3:
   
  Remove and reinstall all USB controllers.
  To remove and reinstall all USB controllers, follow these steps:
  (a) click Start, run, type sysdm.cpl in the Open box, and then click OK.
  (b) click on the Hardware tab.
  (c) click the Device Manager button.
  (d) expand Bus USB controllers.
  (e) right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  (f) restart the computer and reinstall the USB controllers.
  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.
  
  Method 4:
  To update the chipset drivers and check if it helps.
  Update a hardware driver that is not working properly: http://windows.microsoft.com/en-us/windows-vista/Update-a-driver-for-hardware-that-isn ' t-work properly
  
  Reference:
  The problems of scanning: http://windows.microsoft.com/is-IS/windows-vista/Troubleshoot-scanning-problems

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• Windows vista Manager or the device does not recognize the cd/dvd drive

  I have windows vista and it is not recognize my cd/dvd drive. When I click on my local drive (c :)) and recovery hp (d) shows up, I checked my device manager and nothing shows here either for my cd/dvd drive, so I checked the cable but it looks fine.) checked the files of the upper and lower register, but that fact so I just bought a dvd burner external made by polaroid that is USB2.0 and supposed to be plug-and-play, but when I connect it nothing happens nothing. the power turns on two cd players and the disc starts to spin but it stops after 15 seconds and I get nothing. I am confused and don't know what to try. Please help thanks. so I tried to use the running microsoft dvd set and the message I said 'dvd cd drive not detected '.

  I tried these steps with no luck

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Hello mike salinas.

  1. you have any third-party burning software installed on your computer?

  2. have you checked if the external CD drive works on another computer?

  I suggest that you check if your internal CD-ROM drive is detected in the BIOS.

  Usually, you must press a key (for example, F2, F12, DEL, ESC) or a key combination whenever you turn on your computer, but before I get to the BIOS to start Windows. Check to see if there is the CD/DVD drive in the BIOS.

  You can see the article for more information about the BIOS:

  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions

  Regarding the external CD/DVD drive, I suggest you see if it works on another computer.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• I have a toshiba laptop purchased recently. After the scheduled updates it does not recognize the wireless network. I have to do a system restore. is there a solution for this problem?

  I have a toshiba laptop purchased recently.  After the scheduled updates it does not recognize the wireless network. I have to do a system restore.  is there a solution for this problem?

  Hello

  Make sure you have the latest network adapter drivers fron toshiba

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  and if windows update is at the origin of the problem change how to get updates to uncover the problem update

  When you have found the issue, a right click on it then invited uac then hide

  read the information on the link below

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Download updates but let me choose whether to install them - if you select this option, Windows will download the updates on your computer, but not install them automatically. If you want to install updates, then you must install them manually. You should only select this option if you have a reason to not install updates automatically. Only advanced users should use this option.

  Check for updates but let me choose whether to download and install them - if you select this option, you'll be alerted when there are new updates available for download and install. You can then choose to download and install the updates that you want. This option should really be reserved for people who know exactly which updates they need, or those who have little access to the Internet.

• Backup does not recognize the previous backup CD

  When you click on backup:

  1. backup does not recognize the last backup cd. The only beginning of path to create a shadow copy backup is to insert a blank disc. How can I fix it?

  2 ive run backup from one day to the next day while he created a cliché. In the morning, it is only 1/5 complete suggesting that it is not working properly. I canceled the backup. How can I fix it?

  3. If I try to do another backup he asks the cd of your previous (cancelled backup) despite the fact that it was cancelled and the cds do not exist. How to reset to ask these latest records backup?

  Since then, I have downloaded all windows updates but the problem persis

  Thank you, Kel

  You mean by cliché, creation of backup image, right? Shadow copy volume is not Windows Backup.

  If you canceled the backup Windows is trying to finish the last backup. It's normal.

  All over again, trying to backup in a different medium, an external HARD drive.

  At first is a stop at the backup in progress"

  1. Restart the computer
  2. Run as administrator command prompt and run this: wbadmin stop job
  3. Typing sdclt.exe in command prompt and click on change settings
  4. Connect your external HARD drive or DVD
  5. If changing the settings is not available, then click on set up automatic file backup
  I hope that it will work. Please let me know the results to help others.

  Kind regards

  Helene

  Is this useful? Then please click the button to Vote as helpful . Is that an answer? Then click Mark/propose as answer