ReadyNAS shown on the network, but not accessible after upgrade to OS 6.5.0

Similar Questions

• Computer connects to the network, but not to the Internet, connect to the only local

  Hello world

  OK, so I have a HP computer with the installed version of Windows Vista Home Premium 32-bit. I've had it for almost 2 years now and have had no problems connecting to Internet... until now.

  I can connect to networks... both wireless and cable, but I can not get Internet. I used the IP, subnet mask, gateway and server settings DNS to another computer that works with this specific local network just to see what happens... my computer has failed.
  Until recently, I could connect to this WiFi connection in a coffee shop, but the last time I tried it didn't work. I've connected to the network but not the Internet. He told me that the DNS server did not. I'm starting to think that something is wrong with my computer.

  I saw that the solution for some people running the Norton removal tool, however I had uninstalled Norton almost as soon as I got my computer 2 years ago and ran McAfee instead. I don't think that Norton should have an impact on me more.

  Is there a solution to this problem... or I'll just have to try everything that is out there?

  Thanks for your help!

  Hi MomPlaysBass,

  Finally, my problem has been resolved - it wasn't my computer after all. The modem may only be connected to a computer. If you want to connect to another computer, you can connect the computer to the modem and then put it back. My computer worked fine after that. Whenever we want to switch between computers, even if I have to reset the modem.

  I don't think you have the same problem, but just in case, you can try to reset your modem - it's a button on the back or a small hole that you can reach with a pen... Hold the stylus for about 5 sec or maybe a bit more and then let go. That should reset your modem and might help you with your problem. Your computer should also have created a restore point... If all else fails maybe you can try to get back to the final point where your computer worked.

• WRTG54S to connect to the network, but not internet

  I have a WRTG54S and Mediacom 12mbps. My router worked fine on my old laptop (a Dell Vista), he was sitting in a box for about 6 months and now that I have a new (Sony running 7) I can connect to my network, but not internet. I have updated the firmware of 7.6 to 7.8 without change. I have tried no security, wep and wap without change. Also, I cloned the MAC, once again no change. Windows cannot detect all problems, and when I try to activate the router to connect to the internet it always says connection failed. I can connect directly connected to the modem but not when connected to the router or wireless. Any ideas? Thank you

  Problem solved. I had to go to a Motorola SurfBoard 4100 to a 5100. Thanks anyway

• Laptop connects to the network, but not Internet.

  I'm trying to fix a HP DV6000 laptop that can't connect to the Internet. It is running Vista Home Edition. It will connect to my LAN cable or wireless network, but not the Internet. I checked a few things and discovered that the TCP/IP protocol is missing. When I try to add using properties of LAN, TCP/IP is not an option.

  I did a complete system restore. System set!

• My laptop, connect to the network, but not the internet!

  My laptop connects to the network media blank but not internet. My roommates using the network can connect to the internet. I tried various things but not vain. I also tried to get in touch with the Virgin on this subject, but they can help. Is it my laptop and is there something special I need to do with a computer hp laptop. Help, please! Thank you!

  Hello

  On the Start Menu, click programs principally made, click Accessories, right-click on command prompt and select "Run as Administrator".  In the prompt, type the following commands, pressing on enter after each command.  Include spaces in the commands, as indicated.

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int ip reset c:\resetlog.txt

  netsh winsock reset

  Type exit and press ENTER.  Restart the PC and see if you can log in now.

  Kind regards

  DP - K

• 2 13 pro tablet of yoga - to connect to the network, but not the internet

  Hello!

  I got my new yoga today and immediately connect it to wifi...

  It connects to my home but not internet network (or connection very very creepy)

  tried home through my phone LTE and still...

  tried by bluetooth and same result... slow as hell... maybe approx. 10 KB.

  im looking good on the web and don't find anything...

  probobly you are the people with the experience...

  help would be appritiated!

  Kind regards.

  Hey guys quick update!

  After sending the lenovo Tablet and a few screams (sad that we cannot otherwise)

  they replace them with sealed brand new...

  so thanks for the help!

• Published the network Variables not accessible by other computers on the network

  I am trying to create a system where a computer will display network variables that can see any computer on the network, this includes a person bringing in a laptop computer and the connection for a short period.  So I was looking through a large number of forums to find an answer and tried many solutions and nothing has worked.

  This is where I am.  On a single computer if I update a variable network it appears on the DSM NOR (Distributed System Manager) under which the name of the computer and I use this variable and it is updated.  Any other computer connected to the network also appears on the DSM.  On the other computer, he sees the first computer in the DSM, but cannot see any one of the variables.  I also register the IP address of the computer, but it does not help.  If anyone has had this problem and know how to fix?  I had the same problem using my code for the project and the example code in the shared Variable Comms between Executables.Ivproj.

  Thank you for your time

  Mitchell

  I had some problems lately with the network stream. I know that this isn't nearly the same as shared variables, but it uses the same underlying process in windows. In my case, it's the windows firewall in Windows 7 that has the problem.

  This link help me configure my firewall correctly:

  http://digital.NI.com/public.nsf/allkb/0D7B86F4B4D19A5E86256F9A006EECB1

• HP Pavilion 2 x 10-N000NA: HP Pavilion x 2 10-N000NA connects to the network, but not to the internet

  Hello

  I have a problem with my HP Pavilion 2 x 10-N000NA Windows 10, 32-bit version...

  I have a router TP-Link W9980 and the laptop connects to the 2.4 GHz network, but there is no internet access.

  However, if I use a range extender (powerline TP-Link Wireless extender), it connects to the network and the internet!

  So, I guess that the equipment is working well, there must be a setting somewhere?

  I've updated all the drivers, etc. for the laptop and the router.

  Any ideas?  Thank you.

  Hello

  Well, the strangest thing happened!

  There was a huge update of Windows, and it seems to have solved the problem.

  Connections now say '(network) secure' or '(network) open' - which they did not before.

  So now that I know that the network was very good and it was a laptop problem which needed fixing.

  However, I do not know what exactly the update fixed, so I can not pass on any knowledge to solve the problem of someone else who suffer.

• Windows XP sees Win 7 computers on the network, but not Windows XP-based computers (7 can see 7, but 7 can't see XP and XP cannont see XP)

  We just installed a new Netgear Prosafe 16 port switch.  We use a wired Linksys router.

  With 10 computers on the network, XP can't see XP or 7.  And sees only 7 other 7 computers.

  We are able to ping to all computers.  All computers have access to the Internet.

  Network neighborhood shows computers only 7 to 7.  XP doesn't show anything.

  Error message:

  "The Working Group is not accessible.  Migh Tnot you are allowed to use this network resource.  Contact the administrator of this server to find out if you have access permissions. »

  "The network path is not found."

  Thank you!

  Hello

  -Are you connected to a domain network or a home network?

  Please follow the steps below and we update with the results.

  Method 1: Error Message When you try to access a network Windows XP computer: "you might not have permission to use this network resource".

  Please follow the steps described in the following article and check if it helps.

  http://support.Microsoft.com/kb/913628

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  Method 2: Error Message When you try to access a network share on a Windows XP-based computer: "workgroup is not accessible.

  http://support.Microsoft.com/kb/915107

  For more information, see the articles:

  Why can't I connect to other computers?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  Let us know if it helps!

• distance can see the computers on the network, but not their actions

  I rv042 vpn setup linksys was able to vpn in and see the actions on however my client machine can connect and see the computer network but denied trying to see its shares of the GET access.

  XP pro on both

  any ideas?

  Whenever I have problems like this, I'm trying to access the share by using the IP address.  For example, if the IP address of jobloe is 192.168.10.20, then try to access \\192.168.10.20 and see what happens.  If it works with the IP address, but not the name, so it's a problem of name resolution.

• Can ping the router and the computers to the network, but not beyond router

  I have 2 computers in linux and 3 Windows XP computers.  All can ping the router and inside my network.  Anyone can browse the internet.  None can ping outside my network (google.com or its IP address) if connected directly via the switch or router.  Traceroute shows stopping at the router.  Router firewall is disabled.  Ping on the router tool not working anymore. Linksys WRT54G Router is and I've just updated to firmware 4.21.1 but the old firmware is has never worked. I use 192.168.1.1 for the router.  Linux has some IP fixed all the other usind DHCP.  ISP is a provider of mobile phone to the modem.  Just like cable or DSL, I guess.  I've looked everywhere with no solutions.  Anyone have any ideas?

  Yes, contact your ISP to get it resolved.

• Vista can connect to other computers on the network, but not to the internet

  I have a Vista computer that I just reinstalled and it is connected through a router Thomson to a Win7 machine and internet (or at least it should be).  For some reason any Vista machine refers to the network as a public network that I can change this private and turn on discovery.  If I do that, then the machine Vista can see the Win7 machine through the router, but cannot connect to the internet.

  I tried to use the disk driver for the Thomson router on the Vista machine, but at the time wherever he tells me to connect cable internet installation program does not detect that the cable has been connected.

  Troubleshooting with software Vista suggests simply reboot the router (that I tried without success).  Needless to say that the Win7 machine connects to the internet fine.

  I was wondering whether to try to remove the connection and start again, but unable to do so because when the cable is plugged in tells me you cannot delete an active connection and when I disconnect the cable network connection disappears and so cannot be deleted.

  Grateful for pointers

  Ian

  Hi IanRC,

  Try the following steps.

  Step 1

  You can try to disable the antivirus software on your computer and check if it works. Activate antivirus once you check the status.

  Note An antivirus program is designed to help protect your computer against viruses. You must not download or open files from sources that you do not have trust, visit Web sites that do not trust, or open attachments when your antivirus program is disabled.

  Step 2

  Try the Microsoft Fixit. Open the link below and click it on the Fixit button.

  http://support.Microsoft.com/kb/928233

  Check if it works and post back the result.

  Bindu S -Microsoft Support
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• E-all-in-one printer, HP Photosmart 5520 connected to the network but not detected by computers

  Hello!

  My printer HP 5520 indicates that it is connected to my network, but the wireless printing does not work correctly.

  In the implementation of the process of the driver software the printer displayed after resetting my router, a Huawei HG655d. I get a "no connection" error when I try to send a print job to the printer. Function AirPrint doen and the printer is not visible on the iDevices. I have the latest version of my OS (OS X 10.8.3) installed, I also tried to reset and reinstall my router and my printer several times but nothing works.

  Is there a way to make printing wireless correctly?

  Access my printer directly via its IP address works, so the network connection should work. I've added details of the network below:

  Your router may not support Hello, who need your Mac to find the printer.  Enter the configuration of the router and see if there is a way to activate it.  It is sometimes called mDNS.

  Additionally, make sure that the multicast is enabled.

• Xbox 360 recognized on the network, but not as Extender

  Hello
  I've been running my XBox as extender on Vista computer for a year.  Just upgraded to Wireless N router.  Xbox is always connected to the router.  Now XBox appear on the network map, but my computer no longer recognizes the XBox by trying to set up Media Center.  Went through all helps troubleshooting.  Still no luck.  XBox does not even recognize the computer for video/music sharing, even if she has no trouble finding my old XP computer on the same network.  Any help would be appreciated.

  Hello

  The question you have posted is related to the Xbox and would be better suited to the Xbox online community. Please visit the link below to find a community that will provide the support you want.

  http://forums.Xbox.com/

  Concerning
  Anthony.

• can connect to the network but not internet XP

  I use a computer on a local network xp, can connect to the network, ping the DNS server, gateway, etc.  However, I can't not conncet to internet.  When I ping a web address using the address of the site name or xxx.xxx.x.xx I have no success.  Tried to reset winsock, tcp/ip, without success.  Would appreciate any help.

  First course of action:

  1. turn off the PC.

  2. turn off the router.

  3. turn on the router.

  4. turn on the PC.