Recovery of a backup CD...

Similar Questions

• Satellite L300 - 20 d - recovery system disk backup is missing

  I have Norton Protection against viruses and when I backed up my laptop I saved the backup in the D drive which is partition backup drive...
  I want to factory reset the laptop but I can't do t it says can t find disk backup

  Is there a CD I can clean the laptop with... I think there must be something missing in the D drive backup.
  Can someone tell me how to sort plsss
  I have no backup disk and no CD came with the laptop that I lost.

  The history is somewhat confusing.

  Factory settings you can have on two different ways:
  -using the installation discs for recovery
  -with the help of HARD drive recovery option > http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

  > I want to reset the laptop but I t this, as it says t find disk backup
  Can you please explain to us how you tried to reset the laptop to the factory settings and on how you got this message?

• Pavilion g71-343nr: photo file recovery from a backup of the hp system recovery

  I have 5 drives from a backup system recovery HP, how to recover my pictures and my music only
  Thank you

  apsyandme

  Instructions to retrieve the files can be found in this thread: HP PCs - restore files that have been supported to the top using HP Recovery Manager (Windows 8.1). HP® customer support

  Good luck

• Rescue and recovery lists no backup on USB Iomega eGO drive

  Hello

  I have been using an Iomega eGO external backups USB drive.

  I was able to identify and remove (if necessary) backups in Windows 7 and rescue & recovery running, but I can't get the list of backups at the start of a recovery in rescue & recovery DVD.

  Basically I replaces unencrypted with a SSD hard drive that supports encryption.

  The goal was to use a full backup immediately before removing the HARD drive to restore the complete system.

  At the start of the recovery DVDs, recovery utility & rescue lists not all backups, even when the check box for the list of backups on other systems is checked.

  It makes no difference if the selection of THE places or USB external drive.

  Any ideas?

  Backups are not much good if you can't get back them.

  If my old drive did not then I would be in a worse state than this. I can't say I'm impressed.

  Well, I've finally sorted this issue.

  I tried to create a new recovery disk.

  I even tried the recovery time in Windows and see what backups it detected. Yet once, I drew a blank.

  The question was this:

  On my W510 at least, none of the USB3.0 ports are recognized by Lenovo rescue and recovery software when you select the USB storage device. Once connected to a single USB 2.0 port the USB eGo has been recognized and listed backups.

  Unfortunately, this means a minimum of 6 hours to restore from a full backup!

• OneKey recovery has no backup option

  Hello

  Yesterday I bought a Yoga 2 Pro. Updates are finished, and now I want to create a backup on an external hard drive. According to the user's guide, I have to press the Novo button and click the backup of the system. Well, I pressed the button of Novo and there was only the restoration of the system; no backup option. Is the wrong manual or is there something else that I need to first install?

  Thank you.

  Sorry, I thought about her. The Novo button is reserved for them if the PC won't start not (recovery). I found a OneKey shortcut in the Metro interface with a backup option. Despite this, the user guide is wrong and must be corrected.

• Recovery on a backup hard drive that was accidentally erased discs. How can I get another?

  My PC HP TouchSmart 600 all-in-one allows only a single copy of the recovery disc. I got mine on a HDD that has been accidentally deleted external backup. How can I get another set of recovery disks?

  Hello

  You can order a set of replacement recovery disks using the link below.

  Order HP recovery disks.

  If you have a problem with this link, order them directly from HP.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• I purchasedUnable to create the ASR recovery diskette after backup

  I bought an external hard drive to use as a backup of the system. The backup was successful, but in the end, I couldn't create the ASR restore disk. Is it possible to create one now?

  Hello

  You must have the floppy drive to create (ASR, Automated System Recovery).

  Visit the links which has information about how to Set up and use automated system recovery in Windows XP: http://technet.microsoft.com/en-us/library/bb456980.aspx

  How to recreate a lack automated system recovery diskette in Windows XP: http://support.microsoft.com/kb/299526

• Factory recovery Dell Media Backup & Recovery

  Hi, I just upgraded to windows 10, I'm on a dell inspiron 3000 series, I accidentally deleted the partition as dell backup and restore made when I started the software. now when I try to create a new recovery media, I get the message saying that this device is already linked to this recovery factory media?... but there is no new disk partition?... and the recovery of media factory is not checked green?... can someone help me please?, thank you.

  8.1 Windows must be installed to clean:

  http://dellwindowsreinstallationguide.com/download-Microsoft-Windows-and-Office/Download-Microsoft-Windows/download-Windows-8-1-retail-and-OEM-ISO/

  Then, the system upgraded to Windows 10:

  http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/a-clean-install-of-Windows-10/upgrading-to-Windows-10/

  Recovery media can be done natively in Windows 10:

  http://dellwindowsreinstallationguide.com/Windows-10-RTM/creating-a-recovery-drive-and-using-it-in-Windows-10/

  As I said I don't know if there is a compatible version of Dell Backup and Recovery for Windows 10.

• Error occurred in making the disc of recovery with Dell backup and recovery

  Mr President.

  When I was doing a System recovery DVD with Dell backup and recovery when all steps were completed and finally when he was checking the disc a dialog box appears showing "AN ERROR has OCCURRED". How to get rid of this error?

  Please answer fast. Any suggestions will be appreciated

  Thank you

  Hey Himanshu Teli,

  Please provide the model of your operating system and Dell. I would also recommend that you try a flash instead of a DVD disc.

• Rescue and recovery cannot delete backups

  Hello

  I have problem delete old backups with Rescue and Recovery - always when I try to delete them, it seems to work, but it is not, it never ends... I tried to remove one of all backups, only the last or only the oldest or all of them together, but without effect. I have 6 backups about 45 GB together. And by the way that r & R does not well at all - also when I click on optimize backup storage space, it does not work...

  Eventually, it is normal that when deleting old backups, computer seems cold and it takes a long time, but I don't know if it never ends.

  I have the latest version of Windows XP Pro SP3, R & R 4.21.0016 R61.

  Is there a solution?

  Thank you very much!

  V.K.

  Uninstall rescue and recovery of add/remove programs. It will remove the backups in this way.

• Rescue and recovery cannot find backups - EXCEPT in the restore function. Help

  I recently optimized files, including placement
  the disk - machine now flying.  "I wanted to start from scratch with R & R).  Thus,.
  delete all local backups and USB.

  I started a basic backup - initialized manually, close,
  restarted, returned the top could not backups - display Message "No. BACKUPS
  FOUND "hen"show all the backups", or"delete backups"Advanced"
  menu.  However I can find them using the RESTORE OF THE BACKUP.

  Repeated starting a new backup, same results exactly, except
  now I have two BASE backups.  I even started in the R & TV R
  environment may find things out there.  No luck - no possibility to launch a backup Boot TV
  environment, but could restore from the backup.

  I don't see any other choice other that uninstall 3.01?  Do you have?  However, the most recent
  version there is 4.22... Any reason why I shouldn't go to the
  new version?  I read all warning, installation notes, bugs, etc., none seem to apply to me.

  If anyone has any ideas, I would be happy, or if you know any
  reason why 4.22 isn't a good option...?

  Thanks in advance

  Type of computer rescue & Recovery version 3.01 T60 = 2623 - model.
  D7U

  All, I finally managed to replace the version of R R & on the Master Boot Record.

  First, I started with a R boot drive at & R.  You can either use one you did with R & R when (if) you put always a full backup on CD (which I do every year), or the startup disk (a, a) that Lenovo is sent to you with the 7 product Recovery CD, you can restore your PC to specifically state that you received from the factory or store (if you have purchased again).

  R & R starts automatically on startup with the version of R CD R & makes the startup disk (be it when you or Lenovo is the startup disk.)

  My experience is that after you start with this CD, I shut down R & R normally, then restarted the computer by using the MBR (pushing the Thinkvantage or F11 key at the beginning in the trunk) and voila - it starts with the same version that you started with the CD in the last step.

  I also discovered that if you use R & R to restore to a time when the Version of R & R was different from what is working on the MBR, which also change the MBR.  Again, both are good information that will certainly be useful trivia some time.

  Thanks again to all who jumped and provided information that ultimatelly led to the solution

  concerning

  Fred

• With the help of Rescue and Recovery to make backups of 3 different machines

  Hello, I have three laptop Thinkpad T400, X 61 and R61i. I want to back up by using an external hard drive. The HD is divided into three partitions, the smallest of X 61, the middle of R61i and most importantly - for T400. I backed up all my laptops in the appropriate partitions (base backups), but now, so I want to make partial backups, they go to the bigger partition (for the T400). Is it possible (and how) do R & R to always use the same partition for each laptop while safeguarding it?

  A few notes, to respond to your previous post:

  (1) Sysprep is used by administrators to deploy and image system to other machines. Basically, the system starts standalone RNR and save the image (drive C and the same HARD drive partitions) on the service partition.  Comment enumeration pleasure has to with additional partitions on the C drive HDD.  For sysprep to work, additional partitions must be of type Extended. The windows PE, is a windows "skimpy" PRE environment. For win7, the EP is based on Vista with a small set of win7 features added.  Thie PE is used for developers (as Lenovo) to install their systems.

  * None of this applies to a user at home like you and me *.

  (2) the logic used in the RNR for the GUI vs bent the advanced GUI are DIFFERENT.

  Example: the user has part C, D and E on C disk HARD drive.  Uses advanced parms to set backup (local) to go to E drive.

  If the backup through the advanced graphical interface, drive E is honored.

  If the backup is performed through simple GUI, the partition with the largest free space is used.

  Note: using the Second HARD drive don't offer NO choice to designate a partition target of \RRbackups.

  (3) view of backups.  It's clearly too.

  When a backup is performed, and RNR is locked on him, it will REFRESH the registry entries for the content of backup.dats in the \rrbackups folder. Subsequent backups of view will probably be read from the registry. That is to say no record of reloading. Simpified mistletoe might once again, just to use the registry, the locks of GUI in the new backup folder.

  (4) your letter removal/restoration

  a: I have no idea how autonomous RNR will react to the 3 folders on the second \rrbackup, IE the part 1, 2, 3.

  b. If rnr backups locked in the wrong \rrbackup folder, you will have a total mess. A symptom of this: you take a basic (full) backup, and the next backup, which should be an incremental, is actually another full backup.  This error could occur if you deleted the wrong letters.

  (5) you have a mess.

  If I save it again this PC, R & R is a point instead of a differential backup<>

  It would take a lot of work on you end to look in the backup files.  Not worth it.

  Again, the simpifed GUI backup use different logic. He likes the larger partition.

  From what you say, you used simplified and got the base of the machine backup 3 all go good part 1, 2, 3.

  Somewhere in this mess, he locked in a \rrbackups without a base backup folder and took another backup.

  who knows.

  ==

  Release notes:

  Review 4
  ----------------
  Location of backup changes when you select a smaller partition through the advanced interface of the Rescue and Recovery program.

  In the advanced interface of the Rescue and Recovery program, you select a partition more small capacity on your local hard drive as the backup location. Then, you switch to the simplified interface to create the backup. However, the backup is created on the partition with the highest capacity.

  To resolve this problem, back up your system in the advanced interface of the Rescue and Recovery program after you have selected the backup location.

  ===

  The solution is the cleanest way to follow. I would always use the GUI advanced for now on.

• VM data recovery - delete older backups

  Hello

  If I go into the VM data recovery > restoration I can see to test the backups that I did a few weeks ago, how do I remove the?

  I see the backups have a red cross next to them, as I tried to delete last week and he said that they have been marked for deletion, but they are still there.

  Any ideas on how to remove them?

  Here is a screenshot, I can not just delete these old backups:

  

  Thank you

  Click the Configuration tab, click Destinations. Now you will see your destination data store (s). Click on the Destination (in this case /SCSI.0:1/), click on the integrity check. Answering the question 'Would you like to perform a manual check now?' with YES.

  There is a KB article for this:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1029296

• Recovery from a backup made in the database of Sun Solaris 10 g on a windows 2008

  Hi, I took a backup of a database on a solaris 10 machine. (solaris 10.2.0.4 database sparq x 64) with this script:
  
  Configure controlfile autobackup
  
  Run {}
  backup incremental level 0
  format ' ${RMAN_BKP_DIR}/Bkp_%T_Full_%d_%u_%s_%p'}
  tag Full_bkp
  database;
  current backup controlfile as ' ${RMAN_BKP_DIR}/Bkp_%T_ctl_%d_%u_%s_%p';}
  }
  
  After I transferred the files by FTP on my machine Windows Server 2008 64 bit on the witch I already created a database (10.2.0.4 x 64) with DBCA. Now I want to recover the controlfile and here is what I get:
  
  RMAN > RESTORE CONTROLFILE to 'E:\oracle\10.2.0\oradata\WAGNER\controlCORP01.ctl '.
  from "E:\fichiers\Bkp_20090527_ctl_CORP_c0kg2e66_384_1"
  
  From restoration to 27 May 09
  using the control file of the target instead of recovery catalog database
  allocated channel: ORA_DISK_1
  channel ORA_DISK_1: sid = 156 devtype = DISK
  
  RMAN-00571: ===========================================================
  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
  RMAN-00571: ===========================================================
  RMAN-03002: failure of the restore command at 2009-05-27 09:27:20
  RMAN-06172: no autobackup couldn't find or handle specified is not a valid copy or a piece
  
  
  
  Can you help me on this?
  
  Thank you
  
  JP

  Hi again!

  I don't know it. Try the following query and you will see information about the endian format.

  COLUMN PLATFORM_NAME FORMAT A32
  SELECT * FROM V$TRANSPORTABLE_PLATFORM;
  

  Best regards

  Florian W.

• Block Media Recovery and RMAN backup incremental level 1

  Hello
  
  I read somewhere that block Media Recovery will not work if a database is backed up with 1 incremental rman. Is this true and if so is there a work around?
  I can't find it in the documentation of oralce.
  
  Concerning
  Me

  Hello

  Yes you are right, for the recovery block media, you must have full rman backup. Incremental backups are not used by block
  media recovery. Only full backups and archived logs are used.

  See this doc on part III

  http://download-UK.Oracle.com/docs/CD/B19306_01/backup.102/b14191/TOC.htm

  concerning

  Jafar

  Published by: jerome on October 22, 2008 19:51

• recovery of the backup for ipad files

  How can I display files that have been backed up if I did more than 1 backup in the same day? Thank you

  Look here and see what you can find files

  https://support.Apple.com/en-us/HT204215