Restarting try DHCP... Problem

Similar Questions

• Must regularly restart the DHCP Client - HP Pavilion 500-205 DT - Windows 7

  HP Pavilion 500-205 DT - Windows 7 Home Premium 64 - bit SP1

  Realtek PCIe GBE Family Controller - pilot 7.67.1226.2012

  Bought 3 identical machines for our daycare. Set up the same. All work fine except ONE of them becomes inaccessible periodically (every day more or less) on other computers on our small LAN-to-peer Windows. You can see, but cannot access any shared folder. To access OTHER computers on the local network of it there is NO problem. All 3 machines have the same profile sharing, workgroup, permissions, AV, firewall, all settings. I realized by restarting the computer solved the problem immediately but temporarily. I reduced to restart the DHCP Client service. Do all works well immediately, but temporarily.

  I tried the things:

  Call support HP - not useful at all. It is under warranty.

  IPv6 disabled

  Disabled wireless

  Disabled network card stopcock energy saving

  Definition of recovery CLIENT DHCP on:

  First failure = restarting the Service

  Second failure = restarting the Service

  Subsequent failures = restarting the Service

  Reset Fail Count after = 120

  Restart the Service after = 0

  But again, this is not the case for other machines with the default settings. Nothing works except the Client DHCP service is restarted. Loss of access occurs with or without someone connected or using it. It has happened since its first establishment.

  I don't know if the HP warranty covers the OS loaded at the factory. I don't want to restore the thing and start over. I'm not a Pro, just the guy in the office who did these things, but it seems that the network card may be faulty. I don't know if I can convince a person of first level support phone to have me bring the machine in an approved place.

  Any help greatly appreciated,

  Larry

  HP sends a FedEx box to put the thing in picked it up. I'll mark this resolved thing. Thank you all for your comments!

• Windows has stoppped working, search for a solution, restarts ther still problem

  cannot access message Office says windows has stopped working looking for a solution then said to restart but the problem is still there

  Hello

  1. don't you make changes to your computer, after which the issue started?
  2. don't you also get an error message?

  Assuming you are using Windows 7, I would suggest you follow these steps and check if the problem persists.

  Step 1:

  Disconnect all external devices such as printer, USB key, HDMI enabled devices and check if the problem persists.

  Step 2:

  Disable automatic system error reboot and note down the error message you get if any.

  Step 3:

  Check if the problem persists in safe mode.

  Let us know the status of the issue in safe mode.

• Trek PR2000 DHCP problems, maintains a drop connections, perhaps workaround

  Hello!

  A few days ago, I bought the new Netgear Trek PR2000 mobile wireless router. Goal was to have a point of contact for all my devices while traveling and be able to connect to a hotspot or wifi in the hotel.

  Configuration has been fine and I was able to connect to my home network in wireless client mode. My router is a TP-Link TL-WR1043ND running OpenWrt 12.09 Attitude Adjustment, wifi with WPA2-AES, DHCP service.

  The Trek has been able to connect, and the whole system was running. Unfortunately, I realized, that the Trek has kept falling connections every 3-5 minutes with the genius of Netgear annoying pop up and try to re-establish a connection. Sometimes it worked, then the Trek cannot connect at all.

  Since I read that OpenWrt Attitude Adjustment can be problems with some wifi connections, I have improved my WR1043ND barrier breaker. The connection drops continued, including OSX almost every minute. The WR1043ND showed various DHCP-wifi-a failed-to-recognize-errors and in his diary.

  After trying all possible setting changes in the Trek-config (and shortly before returning the Trek), I found something as a workaround. In the Trek-config, I disabled the DHCP Server for the LAN area and assigned static IP addresses to connecting clients. Well at least so far, it seems to work very well. No more connections, no more boring engineering arise not interrupted and try to reconnect, the system seems to work.

  But for now, I'm a little confused as to the reason. In my view, the Trek connects to a hotspot and gets an IP address assigned by DHCP from hotspot. Then the Trek uses NAT to connect the clients attached to the internet. Actually the IP addresses of the DHCP assigned by the Trek to customers connected to the LAN area shouldn't affect hotspot NETWORK settings at all. Normally the IP address and private DNS settings are just for private clients LAN, aren't they? If I'm not completely wrong in my assumption, there could be a bug in the DHCP server on the hike or the way how dynamic the client LAN IPs are handled. From the point where I changed to static IP in the LAN client, there was no error message in the log of the WR1043ND.

  Strange thing... Maybe someone could correct me if my assumptions are wrong? BTW, I use the stock PR2000 Trek firmware (which is something like 1.0.0.9) since there is no other is available.

  Thank you.

  @hksteve I wish to inform you that the fix is now available from our download page.

  Feel free to update your firmware and provide feedback.

  Thank you!

• Windows XP DHCP problem when authentication network enabled

  I have a weird problem with Windows XP. Here's a few of my observations:
  -Computer Lenovo X 61 does not connect to a wireless network with a network (that is, Shared/128 b/WEP) authentication. He can never get an IP address from the DHCP server.
  -J' checked the authentication settings. They work in another computer.
  -If I give it a static IP address (less good family), it connects to the router. However, it is very slow and flaky.
  -It connects to open networks.
  -In addition, if I have a wireless and a wired connection to the computer, the wireless connection gets a quick DHCP server address. If I disconnect the wired connection, the wireless connection works perfectly.
  I tried to reinstall the NIC drivers, apply all updates for Windows and Lenovo SW and looked at the values in the Windows registry. Nothing seems to help.
  Any ideas?
  Computer is a Lenovo X 61 Windows XP Professional

  Hello

  In the past, password WEP engines were rather flaky.

  Try using the HEX string instead of the password.

  Or switch to WPA. WEP does not guarantee these days.

• Linksys WAP200 DHCP problem

  Hi, I have problems with the Linksys WAP200. When you use WPA/WPA2 Enterprise client hangs for about 60 seconds to try and obtain an IP address after a successful authentication. AccessPoints from other suppliers do not show this behavior.

  I did a tcpdump and comapred an accesspoint of another provider in the WAP200 work, and it seems that the WAP200 is reject bids that are sent via unicast DHCP. When the dhcp server sends an offer through broadcast after 65 seconds, it reaches the client and all is well.

  This is clearly buggy since the access point seems to be filtering the DHCP responses, is there an option to solve this problem?

  WPA is a known issue with the WAP54G as well. He breaks the wireless link entirely if you use Repeater/bridge modes. It is possible that Linksys a general isue with WPA in several similar products.

  So that it is resolved I feel Linksys just to be notified in writing. This also provides a written question should be wound.

  Concerning

  Fred

• DHCP problem

  I entered the IP address of my wireless router (the one you enter the internet browser to display the parameters) and be stupid, that I disabled the DHCP. After that, I couldn't even connect to my router or go that meet. A few hours later, I managed to restart (factory reset) the router and now I can enter the address IP DHCP is on. However, again, when you start the computer, it displays the message DHCP - and these hyphens are shown. Then start windows. I wanted to re - configure the TP link router and when I run the Setup from the CD, it says that the DHCP protocol is not enabled. I don't think that the computer is still recognizing the router when connected, assuming that the DHCP is disabled for the tunnel router. I tried a static IP (not sure if I was doing it well), but don't know what to do after that. I changed back to auto, but DHCP appears again as a problem when the computer is started and all trying to install my TP Link. I'm stuck and I have no idea what to do, please explain as simply as possible, because in fact, I went in things I don't understand.

  Thanks in advance

  Hi Adriana,

  DHCP allows your computer to automatically assign an IP address to turn it off, it is not recommended, unless you have your network settings. Please follow the instructions below to ensure that DHCP is enabled:

  1. click on Start and open the control Panel.
  2. click on network and sharing Center icon.
  3 al ' View your active networks section, click on the link to connect to the Local network .
  4. in the Local area connection status window, click the Properties button.
  5. highlight the Internet Version 4 Protocol option and click the Properties button. You may need to do the following for option Protocol Internet Version 6 as well.
  6. make sure obtain an IP address automatically is selected, as well as the DNS server to obtain an address automatically.

  If that did not resolve your problem, contact your router manufacturer or your internet service provider for the correct settings.

  Please keep us updated.

  Kind regards.

• IPhoto library is locked and 'force quit' or restarting solves the problem. Any ideas?

  iPhoto has error message: library is locked. clicking on repair or force quit or restart has not resolved. How can I get the app to restart?

  Can you give us the exact error message? Generally, the most common one said something on a disclock. Is your library on an external? If so, what format is it?

  Also, what version of iPhoto?

  Assuming that is not on an external, try to download iPhoto Library Manager and use the rebuild feature. (In early versions of the Library Manager, this is the file-> control Rebuild. In versions later it is under the menu library.)

  This will create a completely new library. It will then copy (or try) your photos and all associated metadata and versions to this library and as close as possible to what you had in the damaged library fix it. It does this based on the information it finds in the iPhoto sharing mechanism - but it means that things not shared won't be there, so no slide shows, books or calendars, for example - but it should recover all your events, albums and keywords, faces and places.

  Because this process creates a completely new library and does not change your old, it is non-destructive, and if you are not satisfied with the result, you can simply go back to your old.

  https://www.fatcatsoftware.com/iPLM/

• Satellite C870-1J6 wired LAN DHCP problems

  Hi all

  Here, I have a new laptop C870-1J6, which makes my life miserable. It won't start not reliable PXE, and the network card also does not start in Windows.

  On a cold start the PXE boot Gets an address dhcp fine most of the time, but a warm reboot fails most of the time.
  In windows this NIC also does not start. After five to ten minutes, he finally gets an address from the DHCP server. Rest of the network works fine.

  No points for guessing the manufacturer of the network card, of course, there a realtek :-(
  "RTL8102E/RTL8101E PCI Express Fast Ethernet controller.
  PCI ven: 10EC, dev: 8136

  None of the solutions, or can send Toshiba somehow? because I don't think I can do a lot on the PXE problem myself.

  At first, I have to say that I m really wondering why you have problems of LAN under Windows.
  Have you noticed these LAN issues from the first day of use?
  Are you using the original pre-installed OS that you got with your laptop or a facility clean or even company?

  Maybe stupid question, but I assume that LAN is set as first boot device, right?

• Using 3500 as a Wireless Extender DHCP problem iPhone X 6

  Hello

  If all goes well, a simple question with a simple answer.

  Background:
  I stayed away from my DSL provider to a cable provider (VirginMedia). My new ISP is delivered with a modem cable (SuperHub 2 ac) and I connected the two devices together to extend my wireless home network. The cable modem, it's that the two routers are physically apart from others - connected through just their Ethernet ports - the technology of power line (Devolo dLAN 1200 +). Both routers have the same SSID broadcast, but on separate channels.

  Question:
  All devices in my house, the tablets of laptops, phones roam between the two areas wi - fi transparently * except * the iPhone 6 (iOS8.1), this works on the cable modem wi - fi, but not on the X 3500 wireless. I also have an iPad Mini 2 (also iOS8.1) which works too - aptly / wrong I have excluded iO8.1 as the issue. Oddly enough, the iPhone 6 connects to the x 3500 but isn't getting an IP address (the cable modem's DHCP server). Even if a static IP address doesn't help.

  Comments:
  If the X 3500 is configured as a DHCP server, the iPhoen connects (and gets an IP address), but then the default gateway is incorrect (gateway IP address of the X 3500 is not the modem cable remote). I can't find anywhere to specify a default gateway configuration.

  Question
  I start thinking, it is a problem with the iPhone 6 (know all other devices work correctly), but I want to just make sure I am the X 3500 configuration correctly. I am particularly interested in it if I use the right to 'Mode' ADSL / Ethernet. I tried 'Bridged Mode Only' (ADSL) and "Automatic DHCP only" (Ethernet), but does not seem to solve the problem of having the iPhone 6.

  any suggestions on how to fix / help would be most welcomed.

  Thank you!

  Thanks a lot for the details... Now I have a config that works also for the iPhone6.

  Basically, I connected the cable on the 3500 x port and the Ethernet port on the cable modem connected to the internet (via the Powerline). I then changed the network on the 3500 of 192.168.0.x x range (this is the range of network addresses used by the cable modem connected to the internet) to 192.168.168.x. Finally I activated the DHCP on the x 3500 which seemed to be the element that was killing the iPhone6.

  The iPhone6 connects now (which he always did), but with DHCP running on the x 3500 on the new range of network addresses of the iPhone 6 also get a valid IP address.

  Looks like that much just to get the iPhone 6 to work... never found a manual way to specify a default on the x 3500 gateway when you run DHCP (appears by default which is her own IP address - with no provision to change).

  Anyway... This works for now... I'll keep an eye on the iPhoen updates 6, just in case where the anomaly is something specific to the iPhone 6, if something changes I will post here.

  I have attached a picture for furture reference. Thanks again for your advice and support.

  

• z3 is restarted and sd problem

  Hi all

  I just told you about problems with my Sony Xperia Z3 Compact phone and my micro SD card:

  The purchase of my phone, so I presented my card micro sd responsible on 6000 and 800 photos mp3.

  The card is recognized without problems, scanned normally. The problem appeared on the next reboot of my phone. I go then go realize that this train a lot and especially it heats excessively to a boil in a few minutes. Through the application of GSAM Battery Monitor, I see that the "Multimédia" application takes too many resources. This application system includes four processes:

  -Download Manager

  -Multimedia storage

  -Memory

  -Downloads

  I run my application 'Album': no picture, we see that the application looks for the files.

  I run my application "Walkman": no mp3 does not appear, we see that the application looks for the files. Once the phone

  restarts!

  What can I do?

  Remove your SD card and test it on a Pc and phone performs a system repair

  Realization of a system repair using PC Companion , this will often fix questions - this will be factory reset your phone and erase all data so better to save before you start

  Turn off your phone and unplug the PC (Hold to increase the volume and power for 10 seconds)
  Start PC Companion and select the area of support then updated my phone/Tablet then blue fix my phone/Tablet and follow the instructions on the screen - when prompted connect your phone turned off always press and hold volume or back button - this should begin the process of repair or reformatting

  If you use Windows 8/8.1 or a 64-bit operating system and then adjust the settings for PC Companion and run in compatibility mode and choose Windows 7 or XP

• Cisco AP 561 - DHCP problems

  Hello

  We have a customer with a number of AP561, there are 2 configured SSID, IP are provided for each network via dhcp, it is managed by a switch of small business and the other is managed by a windows client server.

  The issiue is that IP address are not always given to the devices, it will work for a while then just stop, until the AP is reset, this seems to be the same for several good AP so I don't think we have any physical AP questions, it can be solved in rest normally the AP.

  I see there are other discussions with people with the same problem, we have upgraded to the latest firmware 1.1.2.3 and the problem is still happening, force wireless is not a problem because the task bar displays full strength.

  Thank you...

  Hello Sir, I am sorry that you are having this problem. The latest firmware is actually 1.2.0.2

  Please download and update your Access Points. In the release notes, it is no indication that this new firmware solves the problem:

  CSCus23303: wireless client cannot get the IP address of the DHCP server after a period of time

  Eric Moyers
  .:|:.:|:. CISCO | Pre-sale technical support of Cisco | Expert on wireless

• Blue screen when you restart the computer "problem event name: BlueScreen, BCCode: 116"

  my computer still restarts and gives me this message and I don't know what the problem

  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.1.7600.2.0.0.256.1
  Locale ID: 1033

  More information about the problem:
  BCCode: 116
  BCP1: 84E25510
  BCP2: 8E8389B0
  BCP3: 00000000
  BCP4: 0000000C
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 256_1

  Files helping to describe the problem:
  C:\Windows\Minidump\080914-17300-01.dmp
  C:\Users\ahmed\AppData\Local\Temp\WER-28220-0.SysData.XML

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  Service pack 1 update.

  
  http://Windows.Microsoft.com/installwindows7sp1

  Learn how to install Windows 7 Service Pack 1 (SP1)

  http://Windows.Microsoft.com/en-us/Windows7/learn-how-to-install-Windows-7-Service-Pack-1-SP1
  
  Additional resources:
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-SP1
  http://Windows.Microsoft.com/troubleshootwindows7sp1

• Restarting the player problem

  Hi friends... I made a simple application which streams. WAV files on net... now recently m get this problem...

  After streaming began and the song ends... If I call "player.start" again to restart the song streaming, it gives me the following exception...

  MyApplication (125) the application does not. process is complete...

  There is no reason apparent is that this is due... Some1 can you please throw some light on it...

  and by the way, I took each exception when starting the player... including the parent "Exception"...

  You can't take this one - this exception is thrown by the disaptcher, and that means that you the app has stopped maintenance of the queue of the event, which results in an overflow.

  This means that something has "blocked" your thread main event.

• SGE2000 relay DHCP problem

  I'm looking for more help with DHCP relay on a switch SGE2000.

  I have configured the two VLAN on the switch, (192.168.10.x/24) VLAN2 and VLAN3 (192.168.9.x/24). I have the Layer 3 switch. I configured the 192.168.10.4 DHCP and the DHCP Interfaces like VLAN3 relay server. All static IP Routes have been generated by the switch.

  If I put a client computer on a port which is Untagged VLAN 3 and try to get a DHCP address from the server on a port that is not tagged VLAN 2 I never get a response.

  I made a few captures package and here is what I found:

  1. I see the DHCP on the client computer
  2. I see the DHCP Request to the DHCP server from the IP shown in the switch to VLAN 3 (192.168.9.254)
  3. I see the server DHCP responds with a DHCP offer
  4. The DHCP offer never gets the client computer

  I can't get a DHCP address to any system not on the same VLAN as the DHCP server. 82 option is disable, and tried him, that made no difference.

  Any help would be great.

  Thank you

  Phil

  Hi phil,.

  Have you created a static route on the DHCP server that points to the network 192.168.9.0/24.

  The entry door for this network, in the perspective of relay DHCP servers, is the IP address of the switch SGE2000 VLAN2.

  I think that if you tried to ping to the IP address of the switch VLAN3 with the DHCP server now, you will not get a response.

  When you create a static route to be persistent in the DHCP server, you should then be able to address IP VLAN3 ping of the switch.

  Best regards, Dave