Satellite A300D - FN keys and fan not detected

Hello

Crashed my HDD (winlogon, MBR, boot,... deleted. Just a disaster), so I have to format the drive and make new instalation of Windows. And it happened Toshiba utility installation. And I can not find the drivers for the FN key. I googled to be called "Utility Flash Cards", but only what I founded is pdf of it. And also my Everest or Notebook hardware control is none of my fans.

So I ask, where can I find it? Or better... is a place of grand ' ol pack after the new installation of the operating system? Why my fans are not detected by the system? Maybe I just forgot to install a driver. It is quite possible. So, where is a problem?
And... I'm just curious, y at - there a programe, utillity... etc. which can control the fans?

I have the Satellite A300D, Windows Vista 32-bit

Thank you very much!

Hello

Can on mate, you can find all the drivers and utilities on the Toshiba site:
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

You must install Toshiba Value added Package. That's all that you need for the FN keys. ;)

But I m wondering about your question about the fan. Why do you think the fan isn't recognized? Everything about the fan will be controlled automatically. You can change only the method of cooling between performance and battery optimized in Windows power management.

Tags: Toshiba

Similar Questions

  • Satellite A300D - is overheating and can not play games

    Hello
    I'm quite desperate. My Satellite A300D is overheating. I can not play new games. Temperature hit 94 degrees and laptop is restarted. I cleaned it several times, very precisely and nothing. So I decided to send it to the official service of Toshiba. After that, the phone is still the same.

    My only hope is buy cooling grease and cooling stock-base. But before that ideas, advice?

    Thanks for everything...

    Hello

    I can understand you mate, but have you contacted Toshiba service center again? You should speak with the technicians and explain the situation. I put t know what they did, do you know that?

    Cleaning of the laptop is still a good idea but if it doesn't work maybe the thermal compound must be renewed. So ask a technician for help laptop.

    By the way: what OS are you using? You can use the same problem with the factory settings and preinstalled display driver?

  • 500-210qe Pavilion: Pavilion 500-210qe: cpu fan not detected after update BIOS

    Pavilion 500-210qe started showing ' 511: cpu fan not detected; F1 = boot' message.  I checked the BIOS rev level and set to upgrade to the latest (80.13 FRIEND) but the problem persists.

    At startup, the cpu fan is not running, but after pressing F1.  Please notify.

    From the least expensive option, replace the cpu fan (which comes with the heat sink) has solved the problem.

  • HP Pavilion 500-164: the printer error HP Pavilion 500:511 - CPU fan not detected

    I have a HP Pavilion 500-164. Every time I start it, I get a 511 - CPU fan not detected error message.

    At the bottom of the screen, it says F1: Boot

    Then he begins to run smoothly. It becomes annoying.

    Examination of the aircraft, but when I find the two fans running?

    What is the problem and what I take in repairs?

    Hello

    Use a can of compressed air to clean any dust from the fans in the PC.  With the side panel, power on the PC and still observe the rotation speed of the fan.  What do you see? slow, medium, or high speed?

    Open the windows to RUN and enter: MSINFO32

    What level of your PC BIOS runs?

    Install the latest diagnostics for your PC. Start your PC and press ESC then F2 to run a diagnostic.  Run a complete set.

  • C.P.U fan not detected at boot

    When I turn on my desktop, it says cpu fan not detected & the bottom 'F1 boot' button appears after pressing on which I can log on, I had windows xp on my computer.

    Please tell me how to fix this error...

    Hello.

    Open your computer case and check the fan I have well connected to the motherboard, and it is infact turns when you turn on the computer.

  • fan not detected

    HP Z800 workstation

    Windows 7 Professional

    error 511 and before error 512 chassis and CPU fan not detected

    It is still in warranty?

    This error message is usually an indicator of a fan or vent. I recommend that you do not use the PC, unless you have checked that the fan is indeed running. If it runs and you still have this error message fan needs to be replaced with a new one.

    If you use your PC with a fan that is not operational, then the CPU will become non-operational for still some time.

  • When I try to activate it with my old key that I got it comes up with an error message saying its an upgrade key and will not work.

    Original title: installation problem windows

    I recently had to reinstall windows for my pc that my HARD drive is dead and when I try to activate it with my old key that I got it comes up with an error message saying its an upgrade key and will not work. Ive phone microsoft and they say, I have to buy a basic disk and then upgrade with the disk that has always worked for me? any suggestions?

    License upgrade and the key that's exactly right, used to upgrade a previous version (Vista, XP) for the version shown on the license (7).

    In order to use this key, you need to pre-install your o/s original eligible before moving to 7.

  • Satellite L850 - 1-5 - no battery not detected and slow down the orange light flashing

    Hello

    I'm helping a friend with a problem with its Satellite L850 - 1 5.

    No battery detected is report to Windows, and the light on the front of the machine of battery flashes orange slowly.

    I saw a few forums suggesting removing the power and the battery and holding down the button for 30 seconds. I tried a few times and seems not to have had any effect.

    Is there something that can be done, or is broken for good battery?

    Thank you
    James

    Remove the battery and start your laptop with AC power only. What happens when you put the battery in place when Windows is fully charged?

  • Satellite A300D - function keys no longer work

    Hello guys!

    I have a problem with my Toshiba Satellite A300D - 13 - PSAK4E.
    Given that I uninstall some programs of Toshiba, my function keys (stop, play, pause, silence, etc.)
    not work more.

    I hope you can help me.

    Greetings of the Germany
    Jeane Wendy

    I agree with Akuma.
    The VAP Toshiba offers a lot of features, and they have other Toshiba Utilities.
    I have my laptop installed Satellite PPV and FN keys work.

    Try with the latest version you can find on the Toshiba site:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  • Satellite A300D-205 - Fn buttons do not work with Win XP

    Hi all!

    I installed windows XP for my toshiba Satellite A300D-205,

    I found compatible drivers and all devices work properly except multimedia functions Fn and sensor-buttons next to the main keyboard!

    I tried to install Toshiba Value Package added, but it does not work in win XP...

    Do you have ideas of how make this stuff work? Y at - it Toshiba VAP for XP?

    All responses appreciated. Thank you.

    Kind regards...

    Post edited by: freackh

    Look, man

    The VAP (value added package) was designed for Win Vista and Win 7 ONLY!
    There is no PPV for Win XP!

    Satellite A300D-205 belongs to the PSAHCE but the Toshiba series European driver page does not provide the Win XP drivers for this series! There are only Vista or Win 7 drivers.

    To be honest, Win XP is oldie was a King in the past, but the King living death the King (Win 7)

    I doubt that you will get Win XP drivers created for this series and so I doubt that you will get to the buttons FN.
    But of course, you can try to install common Module, Hotkey Utility, utility Hotkey to published display to other devices perhaps series (A300, A200, etc.), you could get the tools running that would allow the FN keys

  • Satellite A300D - overheating issue and it stops itself

    Hello

    Computer: Satellite A300D (PSAHCE)

    Bought my A300D two months ago. It was pre-installed with Vista, which, unfortunately, after a while, became so slow, that it was impossible to get anything done. So I decided to install Windows 7, the other day and it worked like a charm. Except for the fan stops after about 1-2 hours of work. Even if the temperature exceeds 60-70 ° C. The computer stops at about 80 c.

    I do not understand why the fan stops working.

    So far, I have tried the following: I tried to clean the fan with compressed air.

    I read this thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=46796&tstart=0 on an update of the BIOS, but the one I found, dated February 09 is the same version I already have. Are there any new?

    I read this thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=46117&tstart=105 that connects this http://aps2.toshiba-tro.de/kb0/HTD84026Q0000R01.htm guide where there is something called Toshiba Power Saver Settings. I searched for her to Toshibas support center, but it can not be found for my model.

    I tried using Speedfan freeware without results. I work as a developer, and I only have my netbeans IDE and Spotify ongoing enforcement, even if the computer gets hot after about 1.5 to 2 hours of work because the fan stops.

    Anyone have any idea on how I can solve this or something else I can try?

    I forgot, I also put the cooling system active strategy.

    Hello

    If I understand you correctly, this happens only on Windows 7. Is this good?

    If so, you should go back to Vista or let's say the factory settings. I assume you are using Windows 7 beta or Release Candidate, and this isn't an official version of Windows. In addition Windows 7 isn't on the market and there is therefore no support of official rider for the time.
    Maybe Windows 7 peut t control the fan settings correctly.

    But this problem could be caused due to a third-party display driver. Then you should try the display driver for Vista on the Toshiba site, maybe it helps

    Welcome them

  • Satellite A300D-15B - off and charging problem

    Hello

    I have a Satellite A300D-15B, running Windows 7 32 bit, which has bought used recently. I encountered some problems and I hope that someone can help me with!

    First of all, the day I got the machine, he spent all of a sudden, but turned back immediately and seems to be ok. Subsequently, 3 weeks later (Saturday 2 July) I was installing some software when I got an AGV virus warning, in a few moments the machine again is turned off suddenly. Unfortuanetly right now it will not turn back and the costs/AC power indicator do not come. After some research, I found that remove the BIOS battery and power dissipation allowed me to turn on the machine. Are there any known issues that could be the cause?

    Second, once I had the laptop to turn on after you stop suddenly on Saturday, I found that the charger will not yet be you register as being plugged in unless I have use the folling procedure.
    (1) disconnect the power cable fuse from the transformer block
    (2) remove the battery
    3) plug into the DC Jack
    (4) plug the power cord for the transformer that causes the power led on the laptop to turn on.
    (5) reconnect the battery

    The laptop then charges normally, I use it to write this post.

    I must use this process whenever the unit is unplugged the sector or charger, which is irritating and also concern that there could be trouble on the horizon.

    Any help would be much appreciated.
    see you soon
    John

    Hi John,.

    You wrote that your laptop runs with Windows 7 and the first question you mentioned could be linked to the operating system only. You can test one thing please? Restore factory using Toshiba recovery disc. The disc will restore original settings of the case which is pretested by Toshiba.

    If it s just a software related problem the recovery disc will resolve this problem.

    Unfortunately, it could be a malfunction of the motherboard also. Are you using the original Toshiba AC/DC adapter or 3rd party one?

  • Satellite Pro 6100: keys Fn does not

    Hello

    Ive got a laptop Satellite Pro 6100. IM of problems using the secondary function keys (I'm not sure what they call them!). When I press the function (Fn) key, the light below the F10 button as it should, but when I press one of the brightness of i.e. F up/down buttons, nothing works!

    I had a quick glance at some of the tool and using keyboard in the Control Panel, which suggests that the driver may be incorrect, so I tried looking for an updated driver, but windows says: I have the latest version of the driver.

    Anyone else have this problem with the SP6100? Can it be fixed? If so, how?

    Any help would be great.

    Thanks - Kavi.

    Post edited by: kavi

    Hello

    Even the windows said that you are using the latest drivers, you need to reinstall the drivers.
    First remove emulator utility Hotkey to display Add & Remove programs.
    Reinstall it modules common Hotkey Utility Emulator for display devices.

    Hope it helps average known us if it works or not

  • Satellite A300D-157 problem with WIFI not working after installing XP

    Hello

    I downgrade from Windows XP in my computer Vista laptop Toshiba Satellite A300D-157 has been too slow, but now my Realtek RTL8187B wireless drivers do not work
    I tried many drivers but the result is the same. Please suggest a solution.

    Thank you very much.

    The wireless network card is Atheros and not Realtek!

    The LAN card is Realtek but not the wireless network card!

    The Atheros driver can be found here:
    http://APS2.toshiba-tro.de/WLAN/

    Welcome them

  • 512-chassis fan not detected

    Hi all

    I h8-1114 office and I put the card mother and hardrive in case Antec 900. I got message from BIOS 'fan of 512-chassis not detected. " From this point, I have to use F1 to start.  I know that this rear fan is no longer connected to the moetherboard. Really, I is not necessary that fan because Antec 900 has a much better fan system. Antec fans are huge and not connected to the motherboard.

    I tried to disable this BIOS message in the BIOS settings, but it seems that there is no option. What should I do to disable this message and start without the use of F1? Thanks a lot if anyone knows.

    ramburak,

    Connect the rear fan on the motherboard or use the left side mount for the original fan option. If you use the rear fan, don't forget to put the fan at maximum speed.

Maybe you are looking for