Satellite P500 PSPE8U: BSOD with Win7

Similar Questions

• BSOD with Win7 on Satellite L305D-s5928

  I have a fresh install of windows 7 and after installation I started the operating system and now made a reboot, it continues to show a BSOD with a memory dump and does not load in windows.
  What could be the problem?
  I just returned it from the repo.

  The error is a system fatal error c000021a

  What version of Win7 is this? Beta RC, RTM?

  Have you updated the BIOS?

  Have you used the Win7 drivers? Or XP/Vista drivers?

  Have you installed Win7 fresh, or you have improved?

  Have you tried to boot mode safe?

• Satellite P500 (PSPE8U) - can not find the drivers for it

  Hello

  I've been and down these forums without success. I watched a lot of forums for the drivers for my P500. I've been through the pages of support sites toshiba of Europe, Uk, Australia and Japan... no chance either. I tried to contact the ebay seller I bought, apparently it is now out of business. It goes without saying that the laptop came without any driver disk. Unfortunately, one of the drives died on me and had no time to do a recovery with all the drivers disk. So now I'm really stuck. Here are the details of the laptop should anyone have brain waves for me-

  P500 - PSPE8U
  Windows Vista 64-bit
  ATI HD 4650

  At the time the largest bad head are the video drivers and my battery life is around 30 mins without the toshiba software. The stock of the resolution is a disaster without the correct driver. I tried the ATI46 drivers * from their site, but the application tells me that my hardware is not supported.

  Any help would be appreciated.

  Thank you
  Chris

  Hi Chris,

  Satellite P500 with model PSPE8U number belongs to the US models and therefore all the drivers and tools that you can find on the Toshiba U.S. page:
  http://www.CSD.Toshiba.com

  Just check the underside of your laptop again for the exact model as P500-S1234 number, then you can find the right drivers for your model. :)

• Satellite C50D-A-133 with Win7 - cannot install the USB 3.0 driver

  I Satellite, C50D-A-133 with Win 7 x 64 and cannot install the usb 3.0 drivers.
  I download the driver from the support site of toshiba for usb 3.0 for win7 x 64 and it starts to install the driver, but in the end it saids...
  Windows found driver software for your device but encountered an erroe trying to install it.
  AMD USB 3.0 host controller
  The system cannot find the specified file.

  I try to point the location of the driver but same error.
  Other drivers installed ok only gives error

  I ve downloaded and unzipped the driver and everything seems OK.
  As far as I know laptops equipped with platform AMD isn't chipset driver and after installing display driver must be installed USB driver.

  Try to download it again and start the installation manually.

• Satellite P500-153 - display with LED backlight?

  Hi, didn't display Toshiba Satellite P500-153 with LED backlight? I want to buy this laptop, but I m a bit confused, because I read about the poor quality of backlight :(

  Thank you

  Hello Andrée,.

  According to the specification on the official website of Toshiba, this model is equipped with normal LCD display that supports a resolution of HD +.

  I have the Satellite P500 in front of me and I m very pleased with the screen. It has a really good and bright backlight so that I can work in the open air without any problem. :)

• Satellite P500 - Touchpad functionality under Win7

  Took me to upgrade to Windows 7 RC, when I got my new laptop and I discovered that my side-scroller has stopped working.
  The touchpad itself works fine, but the side scrolling didn't and I can't find the device for the use of Device Manager, it lists just a PS/2 mouse, so I don't know what brand of touchpad that is or how to get the drivers for it.

  Thanks for the help!

  Hello Dabake

  You use not released operating system.
  Win7 is not officially on the market and didn t Toshiba Satellite P500 for start-up support.
  I mean that you can be happy that most of the functions works well and properly until Toshiba starts Win7 support. This feature is so important to you?

  Anyway, as Akuma wrote most of the drivers Vista works on Win7. Now, all you can do is install Vista touchpad driver designed for Satellite P300 and hope it works well.
  I recommend you to use Synaptics driver version 10.1.7.

• Satellite L755-16U - BSOD with an additional RAM module

  Hello everyone.

  I bought my toshiba Satellite L755-16U nearly 4 years ago.

  This year I decided to buy more memory for my 4 GB,
  I bought Kingston SODIMM DDR3-1333 4096 MB PC3-10600 because they have the same characteristics. Since then occasionally

  BSOD began to take place. I don't know why.

  I checked my drive with chkdsk and checked my memory with memtest86 - no error.
  Separately, the two work well in different locations. I'm desperate.

  Should I buy another a kingstone and try to put in 2 kingstones memories or what should I do?

  Hello

  According to specifications of the laptop, your machine can handle with 8 GB of RAM, so you can use 2 4 GB of RAM modules.
  Compatible 4 GB of RAM has PA3918U-1M4G part number. Part number of Kingston for this RAM module is KTT - S3B / 4G.
  That's all I can say on the upgrade memory.

• Satellite C670D-121 - problems with Win7 recovery

  I have a problem and I need your help.

  I have a laptop Satellite C670D-121 in the original hardware configuration.

  After a message on a process (my 10 year old son told me. "" But I have not seen this message), press the OK button and then the cell phone has rebooted. "
  But restarting didn't work no more.

  Also the recovery with the recoveryfunction of the laptop was not possible.
  Now, I ordered the UDF of recovery and the restoration of the laptop is possible.

  But in the moment where the UDF must be removed and the laptop should be repeated, I see the letters "Start window", the screen goes black and I can only see the cursor.

  After a short time, the cursor jumps into the upper left corner. And then comes the whith window an error message. (s. picture)

  I ordered a new UDF = the same error recovery!
  Support couldn't help me.
  Boot Linux from the CD, the laptop works very well.

  If a HARD disk error and memory can be excluded.
  [photo s | http://www.dienagelschmiede.com/win.jpg]

  Can someone help me please?
  Thank you.

  Hello
  I m not quite about this error message, but it seems that s associated with memory issue I/O (input / output).

  You mentioned a cursor blinking in the upper left corner.
  This symptom is already known to me. I had such a problem blinking cursor also and in my case it was related to abnormal or bad memory and HARD drive.
  I had to replace the HARD drive after all firstly by the modules of memory in order to solve this problem.

  From my point of few your question may be linked to the faulty memory because the I/O message is linked to problems of memory too.

  You said that Linux works properly using the Live CD?
  I guess you booted the laptop using this live cd but did not install the system on the HARD disk.
  Well, I don t think that this could be a clear proof that the RAM or HARD drive is OK.

  In my opinion, these parts must be checked

• Satellite A500-17 x with Win7 64 bit - map gfx says its 32-bit

  Hello

  my laptop, Satellite A500-17 x, on Windows 7 64 bit, but the map gfx says its 32-bit.
  I saw this on the nVidia control panel. I was wondering if the 64 bit OS is having compatibility problems when I play games.

  I posted a thread on the game board on my gambling problem and I thought this might be a contributing factor.

  Thank you.

  Can you please send a screenshot? I have Win7 64 bit and nVidia card and when I open the nVidia control panel and click on system information, everything is displayed properly.

• Satellite L300 - 16L - BSOD with new modules of RAM

  Hello

  I have a Satellite L300 - 16L and make me the same problem.

  Has got 2 x 1 GB DIMMS standard and ordered 2 new 2 GB DIMMS. If I put the 2 new 2 GB DIMMS in I get the BSOD, Memtest also crashes as soon as it starts to test. If I place a 1 GB Dimm in the lower slot and a 2 GB in another windows starts fine, if I try to put the 2 in the lower slot and 1 GB in the higher the BSOD that he.

  But if I put either of 2 GB on the lower slot his own windows boots fine, mem test has also allows to test the two GBs 2 individually and said no problem.

  Any ideas anyone? My laptop is supposed to support 4 GB, I'm sure of it.

  Thank you
  JJ

  Hi Jack_Jumpin,

  > My laptop is supposed to support 4 GB, I'm sure of it.
  Why you are sure that your laptop supports 4 GB of RAM?

  I checked the specification of your laptop on the Toshiba page and this L300 - 16L supports only 2 GB. This means that you can only use two modules including 1 GB of capacity.

  Sorry, mate, but you can use t 4 GB. The chipset supports only 2 GB.

• Satellite C850-1NU - BSOD with Page fault in non paged area error

  So basically I was looking through the web on my laptop, and then suddenly I got a blue screen of death.
  It said Page fault in nonpaged area.

  Some people say it means that the RAM could be faulty.
  Is this true and if it is faulty should I take it back to PC world where I bought it?

  Thanks ;)

  Hello

  The BSOD could be caused by system problems or malfunction of the equipment.

  .. and Yes; the BSOD containing the paginated Page Fault in any area error could be related to memory problems, but it could also be a temporal problem that appeared one last time

  But if this BSOD will appear in the future for the umpteenth time, I recommend you contact the service partner to verify the material.

• Satellite P500 - migrate from Win7 32 bit to Win7 64 bit?

  Help, please. My old operating system is Vista 64 bit and I changed it to 32-bit Windows 7. I would like to install now 64-bit Windows 7, but the system says that the CD that I put (Windows 7 64-bit) is not compatible with the current operating system.

  How I change my OS? I can't change the boot settings. I have a Toshiba Satellite P500 series. Thank you. Hoping someone could help me.

  Besides, even the original Vista 64 bit can t be installed because he says the same reason is not compatible. Thanks again.

  I think you need to do a clean install.
  Do you mean that you can't change the sequence of booting with F12 (?) to the power on?

• Satellite P500-12D - a problem with the cooling system has been detected.

  Hi there everyone,

  I bought a Satellite P500-12D, which was a return of retail. When I start it up it runs a few minutes and then it appears on the screen:
  WARNING: A problem with the cooling system has been detected. Please, turn off computer immediately and return it for service.

  Follow the health of toshiba CPU is less than 50% temp and if it goes much higher that the cooling fan turns on and it lowers down and the fan stops again, I noticed that only the fan works r/h to cool the cpu, both should come together? What is a software problem?

  TThe unit is new without even the plastic off the surround screen or webcam. Any help or even point me in the right direction would be much appreciated, gary

  Hello

  Which program gives you this error message about the cooling system?

  Before contacting a service partner, as you can read in the error message, you must clean the cooling system using a jet of compressed air. Maybe dust blocking the fan or something else. Of more to clean up it of not necessary to disassemble.
  Here is an article on this topic: [how to clean a Toshiba laptop cooling system? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=40]

  If it doesn't help, contact the nearest service partner.

• Satellite P500-1DZ starts only with remote control

  Hi, I just bought a new laptop Satellite P500 after owning a P200-13Z and P300-160 years without ever having had a problem with one of them.

  I have a problem with the P500-1DZ that I bought because it does not start the power button when he was arrested for a period of time, as for example the night.

  If I stopped and immediately press the power button its fine and it starts as well with the remote control.

  In the BIOS, I noticed that there is an option for remote start to the top of the control that is enabled, but Im a little worried about this deactivation in case I can't restart the laptop... everyone has ideas?

  Also for other users of the P500 who are dissatisfied witht the audio output of the laptop, I fixed that uninstall the Audio drivers Connexant HD, then by restarting which allows Windows to install its own audio drivers... which has greatly improved the audio output of the laptop... even if its not as good as the old P300.

  Thank you

  Hi spidercpfc,

  This question really strange s with this start of the issue and I think that it of difficult to say why it happens exactly, but as written Akuma you should try upgrading the BIOS. You can download it from the official page of Toshiba:
  http://EU.computers.Toshiba-Europe.com

  Last week I updated the BIOS of my P500 also and it worked, I t has not had any problems. I updated the BIOS to the version preinstalled Windows as an administrator. Also, I closed all programs running (AntiVirus, Firewall, browser, etc.) and disconnected from the network. After a few seconds the update was done.

  After the update, you should also load default settings in the BIOS. So press F9 in BIOS setup and save these settings.

  I hope this works. :)

• Satellite L850 - Intermittent crashing with BSOD

  My Satellite L850-1LK crashes with the following error message intermittently: DRIVER_IRQL_NOT_LESS_OR_EQUAL (athw8x.sys). An online search in some other forums suggested that I should update the driver for my Atheros wireless network adapter. I did - including uninstall it completely before reinstalling with the driver downloaded from Toshiba's own site.

  I always get the BSOD, so any other suggestions would be appreciated. (I'm under 64-bit Windows 8)

  Hello

  What version of driver and what version of BIOS that you use?

  I had the same problem but not with the Toshiba laptop.
  I discovered that the installed McAfee utility causes the BSOD.
  I suggest that you remove and replace with another software antivirus like Avast! or Avira antivir.
  Both are free and can be downloaded for free.

  But of course I updated the Atheros Wlan driver too!
  You must remove the driver and uninstall the driver properly package.
  This can be done in Device Manager!
  Then clean the operating system using CCleaner!
  Reactivate the wireless lan, then install the latest driver.
  Previous updates must have replaced only part of the package of driver causing the problem.