Try to add the second DC to vCenter instance.

Similar Questions

• Call "HostNetworkSystem.UpdateVirtualSwitch" for the error of the object when you attempt to add the second NETWORK card

  Hi there - first post here, so please be nice :-).

  We are just trying to place an ESX4.1 own deployment in our environment (no previous installation of VMWare) to our main office, using Dell M610 and blades blades M600 to what would become our DR - two sites site hosting VMS on Equallogic iSCSI SAN disks.

  I configured 4 of our blade M610 with ESX 4.1 successfully and they work very well.  These blades have double NIC onboard, and after the initial installation of ESX, I could go to the virtual switch and add in the second NIC like vmnic1 (because one had already been detected during installation).  This fine workd for 4 guests on the M610 blades.  However, I came today to make my first installation on one of the old M600 blades and I encountered a problem.

  Installation went without any problems and I was able to add the host in my vCenter.  I can change all the settings without problem (created the Port of VMKernal for my connection to SAN iSCSI etc, but as soon as I try to add in the second NETWORK card, he paused for a while, and then I get the following error message:)

  Call 'HostNetworkSystem.UpdateVirtualSwitch' of object 'networkSystem-56 "on vCenter Server"VCEN01." ournetwork.local"failed. (network name has been changed for post).  When this happens, it locks up again for several seconds, and when the system returns, I can no longer communicate with the ESX host (Observer of events in vCenter watch 'host is not responding' and I find that I can not ping the host unless I reboot it.)

  If anyone has any suggestions I would appreciate it that I don't want to proceed down to the line with our Installer if theres an underlying issue and I need to redo everything.

  Concerning

  EFIN.

  Do you get the same error when you try to add the network adapter by using the command line?

  1. esxcfg-vSwitch - L vmnic1 vSwitch0

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• Available to add the second internal hard drive to 17-e117dx

  Hello

  Can you let me know, if there is provision to add the second internal hard drive for HP Pavilion e117dx 17.

  If so, one) is there requirments or the specifications of the hard disk (any make or model); (b) what equipment will be needed and where I can get to and c) Finally will be doing so make sure the warranty of my laptop HP Sub

  HP Pavilion

  Product: F9J38UA #ABA

  Model: 17-e117dx

  Thank you

  Not in the way you probably do. Here is the Service Manual:

  Manual

  See Page 50. Unlike the Envy 17 and Pavilion dv7, Pavilion 17 has that a single hard drive Bay. The only way to add a second hard drive is to remove the DVD (optical drive) and insert a DVD to the hard drive bay adapter. The manual shows how to remove the DVD player and you can buy the adapter at amazon.com or jacobsparts.com. Note that this is a 9.5 mm thick disc, not a 12.7 mm. Both types are available. I do not recommend the adapter DVD player solution because you lose the use of the optical drive, and also because the interface of optical drive is usually not as fast as the main hard drive interface. Always fast enough for simple storage and you can run a video of her, but you do not want to edit the video of this disc, for example.

  https://www.jacobsparts.com/items/HDDBAY-02/

  If you decide to go the route of adapter DVD I would buy a large capacity 5400 RPM SATA 2.5 inches wide and drive hard thickness 9.5 mm. No sense in buying a reader more expensive high-performance.

  http://www.Newegg.com/product/product.aspx?item=N82E16822178006

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Using script - library locked when you try to add the file to it

  Hello

  I'm just a simple script that I can run with my engines of the action, so if I add new enum values I can create new wrappers quickly. I am able to create a new VI on disk, but when I try to add the the VI to the library, I get "error 1562: library, or the specified project is locked." Just before adding the article, I tried to adjust the State of the library "Not locked", but has not been the tower.

  Directions to see the error:

  Open attached zip file

  Open 'Engine.lvlib Action '.

  Run "Script - Create Wrapper.vi.

  Please let me know how to get around this, I thank you,

  Gregory

  There are two reasons at least a library locks: 1) something he possesses is running, 2) is open in two or more instances of the application.  (This applies to classes too.)

  I started a project and took your scripts out of the library (to avoid the #1) and then open your Library Reference by path in your script, be sure to include the reference of the application (to avoid the #2).

  Works now.  (With the exception of the Init.vi but you mentioned earlier that you knew about it. But point 1 and 2 of article work fine.)

• I get "access denied" when you try to add the component 4543BD

  I get "access denied" when you try to add the 4543BD to my diagram. This component has been added since a previous version. I use Multisim version 12.0.0 student edition.

  Hi Diarra,

  I checked my database and the 4543 isn't in the student edition. If you open a drawing that was created in a version more recent as the education edition and copied the part to your database, when you place this part, you will get the access denied message.

  Attached is a diagram with the part, you can open it and build you circuit around it.

• My MMC crashes when you try to add the Certificates snap-in

  My MMC crashes when you try to add the Certificates snap-in

  Error: Microsoft Management Console has encountered a problem and needs to close.

  When to see the details, it shows a mfc42u.dll error.

  Hey Sankar,

  Try Mircosoft Fixit: http://support.microsoft.com/gp/slow_windows_performance

  You will need to authenticate Windows.

• I am trying to install a printer wifi (Kodak ESP 7250) and they are both connected to the same wifi but when I try to add the printer, my PC can't find it.

  I am trying to install a printer wifi (Kodak ESP 7250) and they are both connected to the same wifi but when I try to add the printer, my PC can't find it. I made sure they are both connected to my home network and when I go to control panel / printer and try to add a network printer / wireless. He won't find it. Any ideas?

  Hello

  I suggest you to visit these links and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  It will be useful.

• Media center immediately crashes when I try to add the extender for the Xbox 360

  I am running Windows 7 Home Premium.  I try to add the extender for the Xbox 360 to Windows Media Center. When I go to Media Center tasks and add an Extender, Media Center crashes immediately after I enter my Xbox console 8-digit code and click Next.  I have disabled the firewall of the router and firewall windows without success.  Restart the computer and the Xbox has not helped either.  Any suggestions that I can not yet put in place the Extender?

  Thank you.

  Hi Eric,.

  Thanks for posting your query in Microsoft Community Forum!

  According to the description of the problem, it seems that you have trouble connecting Xbox 360 extender for Windows Media Center.

  I will certainly help you with this issue.

  Here are some methods that you can try in order to solve the problem.

  Method 1: Disable the antivirus software and make sure.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Clear the Xbox 360 console system cache and check.

  http://support.Microsoft.com/kb/971755

  Method 3: Reconnect to Windows Media Center

  In the event that something happened to your connection, try to disconnect and reconnect to your Windows Media Center computer.

  To disconnect and reconnect to Windows Media Center:

  a. in the Xbox Dashboard, go to My Xbox and open Control Panel.
  b. Select computers, Windows Media Center.
  c. Select Disconnect.
  d. Select the installation program and follow the instructions on the screen to complete the Media Center Windows Installer.

  For more information, see the articles.

  www.Microsoft.com/Extender/Help

  Here is a demo for an Xbox 360 as an Extender for Windows Media Center unit setting http://Windows.Microsoft.com/en-us/Windows7/set-up-a-Windows-Media-Center-Extender
  http://www.Microsoft.com/Windows/Windows-Media-Center/learn-more/Extenders/help/Extenders-firewalls.aspx

  Tips for solving problems with Windows Media Center Extender Setup

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-solving-Setup-problems-with-Windows-Media-Center-Extenders

  If the problem persists, or you have questions about Windows, do not hesitate to let us know. We will be happy to help you.

• I'm trying to download 11 items that I already have on a new computor windows 8.1 after downloadind the first file and the extraction I get the error message when I try to download the second file: the party reach the components file is missing

  I'm trying to download 11 items that I already have on a new computor windows 8.1 after downloadind the first file and the extraction I get the error message when I try to download the second file: the party reach the components file is missing

  Make sure you have both. (1 of 2) file .7z and .exe file (2 of 2) under the same folder files

  Then double-click on the .exe file (2 of 2) it will start the installation process.

• I have purchased Adobe Design Standard CS6 2013 with serial number, but can't find the to no download on a new mac laptop. When I try and add the serial number to 24 digits on my account it doesn't seem to work?

  I have purchased Adobe Design Standard CS6 2013 with serial number, but can't find the to no download on a new mac laptop. When I try and add the serial number to 24 digits on my account it doesn't seem to work?

  CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  CS6: http://prodesigntools.com/adobe-cs6-direct-download-links.html

• Advanced conditional action does not work when I add the second condition

  I use CP 8. I can't understand why I'm running on this problem. I have a series of If-Then conditional actions, but I am running into problems. I narrowed down it to this problem.

  It is a simple check box that must show either the box or not.

  

  As long as I have only one condition, it works fine. As soon as I add the second condition, it stops working.

  

  Any suggestions? I appreciate the help!

  Rick and I tried to explain that a conditional action is always executed completely. This is the reason that the second decision has been reset what had been done in the first in your first question. I have a lot of articles on my blog where I point out that bad sequence in the decision (or) is causing most of the problems with conditional advanced (shared) actions.

• I try to add the Youtube widget, but I get a plugin saying blocked black box. I even tried to incorporate both YouTube and it does the same thing. But when I drag the widget Vimeo more, it connects properly. What I am doing wrong and

  I try to add the Youtube widget, but I get a plugin saying blocked black box. I even tried to incorporate both YouTube and it does the same thing. But when I drag the widget Vimeo more, it connects properly. What I am doing wrong and how can I solve this problem?

  Make sure that the web browser you are using and its Flash plug-in is up-to-date. Google Chrome has its own plug-in Flash, it updates on its own. Firefox, IE and others have separate plug-ins.

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• Is it possible to add the second cooler to my QOSMIO

  I WOULD LIKE TO ASK IF IT IS POSSIBLE TO ADD THIS SECOND COOLER TO MY LAPTOP * (TOSHIBA QOSMIO - X 300 130) BECAUSE MY LAPTOP SHUTSDOWN WHEN I PLAY GAMES...
  * PIC ALL WHAT I want TO SAY... * http://www.irisvista.com/tech/laptops/Toshiba-Qosmio-X305/big/removing-laptop-motherboard-33.jpg

  AS I HAVE SEE YES BUT WHERE CAN I FIND ONE SUCH COOLER IN YM (BULGARIA)
  EVRYTHING STILL IN WARRANTY

  Post edited by: aloushi

  Hello

  No, it s not possible to add a second cooling fan to the motherboard notebook from the motherboard layout allows and the laptop does not have such extra part.

  But you can test some buffers cooling like this:
  [Photos of cooling pads: http://www.google.de/images?hl=de&q=cooling%20pads&wrapid=tlif130302876 790621 & um = 1 & ie = UTF-8 & source = og & his = N & tab = wi]

• Is it possible to add the second graphics card for this model Y510p?

  I've been doing mixed responses from customer service chat lenovo so I'm posting my question here. Recently, I bought this laptop. It comes with a single graphics card. I heard this model has ultrabay and you add another graphics card. My question is - is it true that you can add a second graphics card in this system by using ultrabay? Please let me know. I'm confused if SLI and ultrabay means the same thing. If this is the case, then this system is not sli. I appreciate your help.

  http://shop.Lenovo.com/us/en/laptops/LENOVO/y-series/y510p/?SB=:000001 C 9: 00011E0A:

  Also, don't forget to find the extra $20 or sometimes $50 discount code for the Lenovo y510p and apply it to the Fund. The time I bought my laptop I used the code USPY5168320, you will find a similar code if this does not work.