U2412M monitor factory Reset problem

Similar Questions

• Satellite T130 - 11 H Factory Reset - problems later

  I factory reset my Toshiba laptop and now I have problems.

  When I start the laptop I constantly get the message "prepare your pc for first use" and it starts, Toshiba menu starts too and keeps telling me it's to complete the installation.

  Randomly, he finished and restarts, boots up to the same problem.
  I tried to reinstall via usb as disk media.

  It s really strange.
  Do you use an installation of recovery for the first time?

  The value of the default BIOS and try again. You can also try to format the whole HARD disk before starting the installation of recovery using your USB key.

• HP 15 laptop: factory reset problem

  I have my laptop HP 15 factory reset and it has been said to 99% for four or five hours now. What is a normal process or should I just wait it out until he finishes? I have my computer laptop factory reset because I could not remember the Windows password to connect to the computer while I was put in place.

  anconelly wrote:
  I have my laptop HP 15 factory reset and it has been said to 99% for four or five hours now. What is a normal process or should I just wait it out until he finishes? I have my computer laptop factory reset because I could not remember the Windows password to connect to the computer while I was put in place.

  That doesn't look good... a couple hours but goes on five hours is something serious goes wrong. Maybe you should order the HP factory recovery disc and try again. I think that something has gone wrong here.

  HP computers - get HP recovery disks or HP USB recovery disc
  Read this before ordering your recovery discs! (United States and Canada only)
  HP computers - performing a recovery of HP (Windows 8) system

• Satellite T130 after factory reset problems

  As the title says I have problems with starting laptop because it always displays the first menu to boot from. Toshiba.
  Why my topic has been deleted?

  The subject was not deleted but moved to another section.
  http://forums.computers.Toshiba-Europe.com/forums//message.jspa?MessageID=257385
  You can find all threads by clicking on your nickname ;)

  By the way: you must follow the first thread to avoid misunderstandings.

• Get a "Cannot find the files needed" error while trying to do a factory reset on ASUS zenbook.

  * Original title: "can't find the necessary files" Factory reset problem Windows 8

  Hello

  So I just bought an ASUS renovated online - zenbook that came pre-installed with Windows 8. There is some unnecessary programs from ASUS on it and the computer worked quite slowly, so I'm trying to do a factory reset, but when I try, I always get the message "Unable to find the necessary files" and then it asks me to insert the installation disk or media, but I don't have one of those. I tried to go to the command prompt and doing reagentc/Enable, but every time I try I get the message "Windows RE image is not found." Then... I don't know what to do and really need help.

  Thank you

  Hello

  I understand the inconvenience caused to you.

  To remove unnecessary programs provided by ASUS, you can uninstall programs and features.

  Here is the link for more information.

  http://Windows.Microsoft.com/en-CA/Windows-8/uninstall-change-program

  If you reset the PC, all your PC applications will be reinstalled. So, I wish that you contact the ASUS support for assistance to eliminate programs and get the recovery disk to perform the Reset if you want to do it again.

  ASUS also provides the partition recovery for certain laptop models, you can check with them and try to reset the score itself.

  Hope this information helps. If you have any other questions about Windows, please let us know.

• HP Pavilion dv4: can I factory reset with an external monitor attached to my laptop?

  I got a laptop HP Pavilion dv4 entertainment PC. It has a cracked screen and I use an external monitor attached. Can I do a factory reset with the attached external monitor? The monitor is an HP w1815 LCD, case ini that matters.

  Thanks for any help on this.

  I would like to add that I can see on both screens only on screen cracked that I can't see the bottom of it due to cracking. As recovery options are visible on the external display, it would be prudent to start the recovery process? I made a few choice, but I am now at the point choose to 'pull the trigger' and click next to start it or hit Cancel.

  Thank you.

  Hi @Auntboris,

  Welcome to the HP Forums!

  It's a great place to find answers and advice!

  You have the best experience in the HP forum, I would like to draw your attention to the HP Guide's Forums:

  Learn how to post and much more.

  I take that you acquired an HP Pavilion DV4 laptop and want to know if you can do a factory reset with an external monitor because of the cracked screen.

  Yes, you can always make a recovery.  Here is a link to HP Notebook PC - perform a recovery of the system (Windows Vista) HP

  Here is a link to HP laptops - how to restore backup files created during the backup procedure F11 to help restore your files if you selected this option.

  Please keep me updated.

  Good luck!

  Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as yourself. Please consider tagging the post in order to solve your problem as "accept as Solution" to help other members of the community!

  To show recognition for my efforts, please click on the ""Thumbs Up Icon " below."

• Factory reset wireless router connection problems?

  Hello

  I recently did a factory reset on my HP6745f desktop running Win7 sp1 and I don't know if my problem is with HP or Linksys/Cisco (my router). I already contacted the support Cisco who reported the problem seems to be "a matter of HP, a corrupt driver or other third-party issue" and then offered to help, for a price. I'm hoping to avoid that if possible.

  This office computer is directly connected to the router via an Ethernet cable. Cisco software was that I want to install that 'control' of my router (called Cisco Connect) and when I try to install the software, I get a message saying: "We could not find your router" (that's why the software will not install) - although I am accessing internet through that router. Even if I try to enter my network name and the password, it cannot find anything. I am also unable to access the router via my browser "168.198.1.1".

  I am unable to connect wireless with the same desktop so, my 2 wireless laptops have no problem of connection at all, which leads me to believe it's something specific to my desktop pc.

  The Cisco Connect software has already been installed on my desktop and it worked fine. I guess my question is: someone has any suggestions for me? This could be a driver problem? How can I identify what (s) for 'check '?

  Any help would be greatly appreciated.

  I thought about it! My router can use a "network key" to connect other computers to the router. I guess when I reset my pc all this info has been removed and the router could not communicate.

  I have just created a network key on a flashdrive USB of my laptop, plugged the USB in my office and hop, I reconnected properly. Thanks for the suggestions, I really appreciate the help.

• problems printing e-Studio 160 / factory reset

  Hello

  I have a multifunction Toshiba Copier e-Studio 160. After trying to connect to an office network and off it, I lost the settings I had set up on my Copier. Now whenever I use the copier I get "cut" copies; I mean that the copies printed by the e-Studio160 do not include all of the original.

  Does anyone know how I can set up border printing or how do I do a reset?

  Thank you very much.

  I see that no one was able to provide a solution to your printing problem.

  I found e-Studio 160 manuals (manual Local and network operator)
  http://www.Eid.Toshiba.com.au/n_manuals16-160-20-200-25-250.asp

  I recommend you to consult these documents. Probably you will find the details in these documents how to print borders, or how to do a factory reset

• What is the problem with my iphone? He says still no service but my sim card works with other phones, after a reboot it says searching until I have to remove and reinsert the sim ive done all what is the factory reset to open the phone to verify any damag

  IPhone 6 64 gb

  iOS 9.2.1

  The phone says no service but the SIM card works, everything in the phone works except the flash still lights up and flickers sometimes before becoming stable but who don't mind not 'that' much, ive tried factory reset and everything, ive also open the unit and looked for signs of damage, the phone knows there is a SIM card in the phone , but he never says the name of the carrier, also after the restart he said looking and does not stop until I have remove and reinsert the SIM card.

  You can restore the factory state after an iTunes backup

  If this does not resolve the problem then you may want to align on Apple or an approved repair shop

• [SOLVED] A3500-FL problem after factory reset

  After a hard reset / factory reset I have boot, but after that, all I see is a black screen with a rotating circle / turning point in the middle.

  I can access the notification area, but I can't access settings or Launcher.

  help, please!

  P.S. I read this drug on this model and could not find a solution. Any help will be much appreciated

  AMAZING!

  the problem was that I was holding the tablet in portret orientation while it starts.

  So, I've ACCIDENTALLY keep it in LANDSCAPE mode, and voila! He seized the allowed parameters. So easy!

  I hope this will help others

• Problems with factory reset on a Packard Bell

  Hi cox.haley1,

  After a Microsoft update Tuesday May 13 laptop Packard Bell Easynote TK85-GN-051UK of my granddaughter had a huge problem with the start-up that could only be ordered with a Factory Reset. Finally I had all this work and re-installed all software programs. Several days later, after update of Microsoft more, another problem arose that could only be fixed again with a Factory Reset, so I had some things to begin to repair, but it got stuck in the Installation of the software... Install Office 2010...33/45

  18hrs. later he was still stuck there.

  I sent to Packard Bell for re-installing operating system Windows 7 DVD & utilities drivers & Applications DVD... Incl. postage. £37.

  They have not worked as once more stuck in the same place.

  Packard Bell is a Dutch manufacturer and a subsidiary of Acer will help so I don't need to waste money on recovery discs.

  Can anyone suggest something to help please?

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/Windows-cannot-complete-installation-in-safe-mode/5e913a56-B29B-4386-A462-20e1991a1edc#LastReply

  Thank you. All sorted now. There is a corruption of Microsoft Office files. Formatting of hard disk. Re-installed my Windows 7, etc and then all software, updates everything and now all is well again.

• Problem to use "factory reset" Cisco VCS!

  I have problems with equipment of VCS to achieve the formats it, when I use the command "factory reset", it shows me an error with the number series and the release-keys as you can see in the picture as an attachment.
  In addition to the above problem, it does not allow access to the console with administrator only with root user interface and does not connect via the browser (white screen).
  Anyone had a similar experience, or have information which may help to be able to format the device to see if the return to normal operation?

  When logged in as root, you can manually enter the release key into the system.

  Use the following command:

  echo 1234567890123456 > /tandberg/etc/rk

  where 1234567890123456 is your key to unlocking 16-digit following, restart the VCS. Wayne - don't forget the frequency responses and mark your question as answered as appropriate.

• Pavilion dv6t-7000 CTO: problem factory reset Windows 7 to 8

  Hello

  My laptop came pre-installed with windows 7, I've upgraded to windows 8 when he was out. Now, I want to do a factory reset me back to window 7.

  (1.) I tried to use the HP Support Assistant on my PC but received a message that there is 'some missing files', was able to complete the restore process and that I should "insert media". I then inserted the recovery that I was responsible for copy for security reasons. I got a message saying "try again".

  2.) I tried tune security, it's the same deal.

  Please, help because I don't know if my recovery is corrupted and when he is grateful the disks copied recvoery.

  Assistance on how to use the restore disks would be highly appreciated. *

  Thanks a bunch

  Please read This GUIDE on how to perform a restore of the entire drive.

• RNDU2000 problem after factory reset

  Hi all

  A friend of mine gave me his RNDU2000.

  I tried a factory reset. RAIDar find to restart and gave me the choice. I chose XRAID2.

  After several minutes (test drives, intallatation...) device reboot and stuck with these configuration LED: Power On, Bill, 1, 2 flashing.

  RAIDar is more and I had no access to admin frontview.

  I changed hard drives, are doing a factory reset again and got the same results...

  Ping device response.

  Any idea?

  The firmware on the flash has been corrupted, so I put the latest firmware on the flash.

• Laptop computer Lenovo running Windows 8 factory reset (damaged Sceen) while unattended.

  Good evening everyone

  Could someone please help in a process that could help tracking? My Lenovo laptop running Windows 8 had been trying to run a factory reset and, unfortunately, while left unattended, my younger brother accidentally shot the cables, resulting in my now... current portable computer damaged screen. I left my laptop Lenovo intact and charged through my diet (Yes, I removed safely the internal battery) for more than 24 hours in his supposed factory reset process. I'm unable to view the entire screen and reading a part of the legend that led to believe me that my laptop is in a phase of repair? My current attempt must connect an external monitor to my Lenovo laptop and the caption "D - SUB POWER SAVING MODE" APPEARS. There may be ways to substitute this mode or could someone help please I can find myself having a restless night without solving my unfortunate situation.

  Kind regards

  Use chic

  Hello

  Welcome to the Microsoft community.

  The parameters of the screen and the screen shorts can be different for each OEM (Original equipment manufacturer). That's why I suggest you to contact the manufacturer of your computer.
  http://support.Lenovo.com/us/en/SelectProduct?c=1&returnUrl=%2fus%2fen%2fcontactus

  I hope this helps. Let us know if you have other problems with Windows in the future.