Unable to connect to laptop E1200 Vista.

Similar Questions

• Unable to connect XP laptop to my wireless network. Diagnotics says 'error trying to validate the Winsock base providers' couldn't get cable or Internet.

  Unable to connect XP laptop to my wireless network. Diagnotics says 'error trying to validate the Winsock base providers' couldn't get cable or Internet.

  Hello

  Try the methods below to solve the problem.

  Method 1:

  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357

  Method 2:

  How to determine and to recover from Winsock2 corruption in Windows Server 2003, Windows XP and Windows Vista

  http://support.Microsoft.com/kb/811259

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

• Unable to connect my laptop XP Prof on printer Officejet J6450 AIO usb (in network)

  Due to some problems of scanning, I have reinstalled my AIO on my USB port of office instead of the old Dell (Windows 7-64) ethernet link. However, I'm unable to connect from my laptop with XP Pro. I downloaded and installed the latest version of the software of full J6450 and can do a test print, but cannot access the printer through the center of Solution, that's why the scanner and other features are not available from the laptop. Also, is anyone know hence the hp software file is extracted to so I can re - run the Setup file?

  The IOA has a w/l button, so I'll try an instalation w/l on the laptop.

  Hello Tracer_C

  Thanks for responding. The error was 'the scan cannot be performed because another program or computer uses... ". "The w/l installation was successful, after that several unsuccessful attempts. (I accept the blame for it). After 2 or 3 tries, I noticed the obligation to connect the printer to the USB port of the laptop to install the drivers. Apres_que the drivers have been installed the software it reset the network, and it does not connect until I plugged in the printer on the desktop).

  I thought I could do a no-w/l installation, but it is just as well, because I don't often print the laptop anyway, so I can keep the w/l off on the router function until I need to print from the laptop.

  I found the installation for Xp folder: C:\Documens and Settings\Temp\7Z***.tmp\Setup.exe Settings\nom of utilisateur\Local.

• OfficeJet Pro 8610: Unable to connect 2 laptop HP Officejet Pro 8610

  I have 2 HP laptops each with Win7 (64 bit) SP1 and I'm trying to connect to the computer laptop 2nd in an OfficeJet Pro8610 to print wireless.  I tried using the CD rom and download the drivers online but I can connect this laptop to the printer.  I get to a point where the login process requires the printers claim id code but when I enter the code I got a message that this code is already in use (the other laptop is connected wireless) and in order to connect, I have to delete the other laptop.  I am at a loss here because I had both the same laptops connected to my old 6700 OfficeJet and could print without any problem installing wireless at all.

  What I'm missing here with the 8610?  Thank you

  Alkymst

  Alkymst

  The code you enter is likely to set up ePrint for the printer address.  Once this has been done it is not necessary to do it again.

  An alternative is that the laptop is connected directly to the printer with direct wireless wireless.  In this case, you will need to disconnect the laptop computer from the printer to use the other laptop.

  A better configuration would be to connect the printer to your router wither wireless or cable LAN cable.  It would give the IP address which you can find by pressing the front panel of the printer to the printer (if the printer is in mode "sleep"), then tap the wireless at the bottom of the screen.  This will bring up the LAN wireless status, where you can find the IP address of the printer.

  You should be able to set up the printer with the driver available at http://www.hp.com/go/toolsinstallation wizard.

• License is disabled and unable to connect to internet after Vista Home Security 2012 malware

  Original title : Ceased to be able to connect to the Internet and Messagesays invalid Vista

  No longer can connect to the Internet will pop up saying threat privacy, another attack Vista Home Security 176.224.57.149 Alert 2012 port 45168.  Then an internet window saying Windows Security Center. Now, he also says that my licende is not valid.

  Hello

  Vista Home Security 2012 is Malware.

  The link provided in this answer read the different names that it goes under and the recommended uninstall information.

  http://www.bleepingcomputer.com/virus-removal/remove-win-7-AntiSpyware-2012

  As you are denied access to the Internet > press F8 at startup > in the list of available options select Safe Mode with networking by using the arrow keys > press > now you should have access to the Internet, unless you are using a wireless connection, follow the instructions to remove on the link provided. If you are using wireless on a laptop computer, use an Ethernet cable connection.

  See you soon.

• Unable to connect the laptop to the printer in a home network

  I just installed a HP Pavilion dv4 laptop, running windows 7 (64 k) and a router Linksys E-1000 of wireles in my home network, consisting of an HP pavilion a6150y desktop, running MS Vista Edition home premium (32 K), to which a HP Photosmart C4280 printer is connected via a USB port. All internet and e-mail functions work perfectly across the home network, except that I can't print from the laptop to the printer. I understand that the C4280 should function as a print server through the Desktop, but I can't print from the laptop. Heterogeneous operating systems cause inability to print from the laptop? Any suggestions?  The laptop has no problems printing to the C4280 when connected directly via a USB cable to the printer.
  Troubleshooting: I ran across the network installation procedure, but nothing helped. The printer has never worked since installation of network components House (e-100 of Linksys and the HP dv4 laptop) anyone can propose a solution?

  First of all, you need to set file/printer sharing and share the printer. If you have already done this and can successfully transfer a file both ways between the two systems, ignore the information of networking at the end of this post. Then you download from the site Web of HP for Windows 7 64-bit print drivers.

  http://welcome.HP.com/country/us/en/support_task.html

  Install the printer on Windows 7 computer and it should be considered during the installation procedure. If it isn't, then install the printer as a local printer instead. To do this:

  Go to the computer to which the printer is connected. Note the name of the computer that you will get to the control panel > system > computer name. Now in the Panel, go to the printers. Find the printer in question, right-click, and then click Properties. Note the name of the share. Of course you must have already set up file sharing / print on all computers involved and share the printer.

  Now, go to the remote computer to which you want to add the printer. Control Panel > printers > add printer

  Click Add a local printer. Click on create a new port. The default value in the drop-down list box is Local Port. Don't change that. Click Next. A dialog box appears for you request that you enter a port name. Type in the \\FullComputername\SharedPrintername

  ex: \\mycomputer\HPDJ (that's why you wrote the names of computer and printer in the first step)

  Click Next. In the manufacturers list, select the correct printer manufacturer and the correct printer model in the Printers list. Under "do you want to use this printer as default printer select"Yes"(if you do!). and click Next. When asked to print a test page, select 'Yes', then finish.

  If you have not already created your LAN file/printer sharing:

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  The Windows 7 network type must be on "Home" or "work". The type of Windows Vista network must be on "private". "Public" is for when you are connected to an Internet connection 'foreign' as an Internet café, at Starbucks or a hotel, etc. In Windows 7, go to control panel > everything in Control Panel > network and sharing Center. Click on "change the advanced sharing settings. You don't want to use the residential group unless you have all Windows 7 machines. If you do and you want to use the homegroup, see Windows 7 Help & Support. Otherwise, in sharing advanced:

  Discovery of plug in the network
  Open the files and printers sharing
  Turn on the sharing section Public folder sharing
  Plug the password protected sharing

  In Vista, turn on password protected sharing.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, turning on window file sharing and printer as the above will take care of that for you. In XP, you can run the Network Setup Wizard or just enable file sharing / print in the Windows XP firewall exceptions. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  Start > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  XP - set up Windows to automatically connect (MVP Ramesh) -http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers on your network are XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. In Windows 7 I usually share the Desktop of the user and the Public directory.

  MS - MVP - Elephant Boy computers - don't panic!

• Unable to connect the laptop to the TV via the s-video port

  I was able to connect my PC toshiba laptop (windows XP) to our old TV using an s-video cable.
  We have improved tv to another TV (pdp-507xd) and I can't the link with the laptop.

  I tried the s-video and also a RGB. The RGB show on 'view', as if I'm linking to a PC. The s-video looks ok but no display on TV.

  I miss something really simple, but any ideas please?

  Hello

  To my knowledge on many television s-video option must be activated first.
  I put t know your TV device and I m really not a TV expert, but check the user manual and check if this option should be enabled before using it!

  Then again try the FN + F5 key combination to switch to the TV device!

  Good luck

• Unable to connect my laptop to the new wireless printer - error "installation failed" after entering my password/security key (WPA)

  I just bought an Epson printer. I went through the installation process on my laptop but I get the "Failed to install" error message after entering my password/security key (WPA). I am with BT and my home hub I have "Wireless Key", "PIN WPS wireless" and "Admin password" - which is it? I tried all three and not joy. Help!

  It is almost certainly looking for your "wireless key".

  The WPS Pin is only used if the printer supports "Wi - Fi Protected Setup" - which it probably isn't, and the "Admin" password is used to access your BT home hub to make configuration changes.

  In addition to identifying what wireless Epson printer you have, you can either

  • b changes to the configuration of the printer from a screen on the front or
  • (b) to connect to the printer by an Ethernet cable or
  • (c) to connect to the printer with a USB cable?

• Unable to connect to laptop after name change

  I have a laptop on my domain name that I use RDP to configure. I just took the laptop out of the field to change the name, now that the laptop has been postponed on the field, I can connect is using the name of the computer.  However, I can connect using the IP address assigned.  What can I do to be able to connect via the name?  Thank you

  Hello

  You need to change the name on the server, to associate the new name with the old IP.

• Unable to connect to the Windows Vista profile, receive the error message "logonui.exe - bad image".

  Original title: bad image Logonui.exe

  I have laptop Dell XPS M1530.  Last night when I tried to start the computer, it went through the movements until he got to the login screen.  Rather than get the profile to connect to, I got the error message following "logonui.exe - bad image.  C:\windows\winsxs\x86...\COMCTL32.dll is not designed to run on Windows or it contains an error. "When I click ok on the error message and wait for an another error message appears" logon.scr bad image. "  I tried to run the Startup Repair and restoration of the system without result.  I cannot lose the files on the hard drive, but have run out of ideas and options on how to solve this problem.  Someone at - he had this problem and managed to fix it?  I've exhausted the System Support of Dell, as they have failed to: "format the drive and restore to original state."  That is not an option right now.

  I went into the Commpand prompt and delete files that have been raised as errors.  When I rebooted, it came in fine.  I got the files I needd for backup and then rebuilt the system.

• Unknown connection status - unable to connect to the Internet, Vista

  Hello. My computer was working fine last night, but when I started it today, I couldn't go online. When I move the mouse over the network and the share icon in the lower left corner of the computer, he said: "the dependency service or group could start unknown Connection status. When I try to diagnose the problem, I can not because the diagnostic policy Service is not running. When I go to the Open Service Control Manager, access is denied.

  Meanwhile, I keep getting warnings that my firewall is not enabled. When I try to enable it, I get a message that Security Center can't turn on.

  I ran Avast and he found nothing wrong. I tried to do a system restore, but that did not help. I tried to go to "Connect to the Internet" via the control panel and network layout and I was told that the wizard has encountered an error and could not connect. I can't connect and I can't always turn on a firewall. What should I do? Please help me.

  Hello

  Maybe an update caused the problem, although it could have been something different.

  Try a restore of the system to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. If after a day or two there is no
  causing problem of updates then restore the automatic updates.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall
  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Unable to connect to laptop using the microsoft account

  Try to connect to computer laptop microsoft account and he said: I can not connect at this time. Change password etc. After several attempts can usually be connected but so annoying - try again now after 50 minutes. You have to go on another computer (apple!). What is going on. I want more convenience

  Hello

  I'm sorry to know that you can not connect to the computer. Let me try and help you with this problem.

  (1) you have an active network connected to the PC?

  (2) did you do with the last changes made to your computer before this problem started?

  (3) are you able to connect to Microsoft online account? https://account.live.com/

  (4) using an Internet connection wired or wireless?

  This happens usually if there is a network connection problem or it could be a temporary problem.
  
  First, if you are a using a wireless connection, please connect your PC to a wired connection and check if you are able to connect.
  If this does not help, you can reset the password and check that helps. You can connect to the Microsoft website https://login.live.com/ account and reset the password, and then check.

  Let us know the result. If you have any other questions, we will be happy to help you.

• Unable to connect TV laptop with Intel WiDi 42VL963G

  I wanted to ask you kindly a helping hand because I'm having trouble connecting my computer to the TV via intel WIDI.

  I declare that they are in possession of a TV TOSHIBA 42VL963G accompanied by key dongle WLM-20U2
  The COMPUTER AND ' a LENOVO... S300 fully compatible with the intel wi - di. "I also downloaded the updated firmware TV proposed by you. So all is good.

  Now, I describe the steps that I followed and where it gives me problems:

  1 APRO TV AND AFTER LAUNCHING THE APP WI - DI MI NORMAL SCREEN IS SHOWN FIRST CONNECTION

  2. AT THIS POINT AS SUGGESTED APRO APPROX. COMPUTER WI IT WORK BEGINS TO LOOK FOR THE ADAPTER.

  3 ADAPTER IS RECOGNIZED AND IS REGULARLY PRODUCED IN THE PC OF THE SCREEN. WITH THE NAME OF "TOSHIBA LCD TV' AND DO I select ' START THE CONNECTION.

  4. at this POINT on TV, I get security to 4-DIGIT NUMBERS THAT I insert, AS suggested on THE PC THEN I click on CONTINUE

  5. HERE "START THE PROBLEM: THE SCREEN FOLLOWING INSTEAD OF"
  HOW DOES the DEVICE TV, MI IS a DEVICE BEARING THE NAME OF "Mstar-TSB."

  6 PROVO OTHERWISE CONTINUE WITH WHAT IS RECORDED
  * THE PC if you click on THIS TEMPORAL CODE 8 FIGURES MADE BY PC as instructed ' CONTINUE it BUT NOTHING...

  I tried and tried everything I get is always the same device instead of TV 'Toshiba LCD TV' and the computer cannot of course REGISTER AS A LINK.

  Hello

  In order to use the Intel WiDi the Toshiba Dual Band
  Adapter WLAN WLM-20U2 is necessary.
  Do you use this adapter?

  Also you can find here in this manual detailed step by step instructions how to use the Intel WiDi (page 56)
  http://www.Toshiba-OM.NET/LCD/PDF/English/Country_Specific/VL963-424755-English-specific.PDF

  In addition the name of the device TV Intel Wireless Display he is editable.
  a preferences menu, press B or b to select Setup and press OK.

  b press B or b to select Intel® Wireless Display Setup and press OK.

  c select Intel® Wireless DisplayName, then press OK. The software keyboard window will appear.

  d enter the name of the Intel® Wireless Display device using the software keyboard (see page 46). Press the BLUE button.

  e highlight done and press OK to save your settings

• Unable to connect to the Internet - DNS error - Windows 7

  Hello

  I have a new (3 months) desktop XPS from Dell with Windows 7 (64-bit), the Motorola SBG6580 Wireless Modem/Gateway and Comcast is my ISP.

  My computer is connected to a modem with an Ethernet cable. Nothing unusual in the installation program. I just plugged my PC and it worked.

  In the last three months everything worked well. Then all of a sudden, from Friday last I can no longer access the internet.

  The connection at the bottom right shows that I'm connected, and every few minutes a yellow exclamation icon above him. Some sites Web opens very, very slowly, some are open to all and another just give a straight error that I'm not connected. It's weird - I can connect to the first seconds when I restart the computer and the speed is extremely fast, and then all of a sudden I can't connect.

  When I right click on the connection icon for helps out sometimes it says "The DNS does not" and sometimes he can't detect any problem (but I can still access all Web sites).

  Now, I also connected with Ethernet cables to the modem game both consoles and they work very well - I can get online, play games, stream movies etc. My wife and I can also connect our iPhones over Wi - Fi, and I can also connect my laptop running Vista by Wi - Fi.

  The problem is just the Windows 7 PC.

  I already googled the problem and tried all the solutions offered - I rinsed and renewed the DNS using the commands ipconfig, I put the DNS manually but nothing seems to work!

  Could this be a virus any? I have McAfee running and I did a scan, but it does not detect. My feeling is that there is a virus which changes the DNS.

  Any suggestion on how I can confirm to you, or what other measures can I take?

  Thank you!

  Hello

   
  Perform the steps mentioned below and check if the problem persists.
   
  a:  Click on start and then Control Panel.
  b: go to work in network and sharing Center and then click on change adapter settings.
  c: right click on Local area connection and select Properties.
  d:  Select Internet Version 6 protocol, and then click Properties.
  e: choose DNS servers obtain address automatically, then press Ok.
  f: choose address automatically get IP.
  g: repeat the steps for Internet Protocol version 4 as well.
   
  Hope that helps.

• When you try to connect from my vista desktop to my laptop windows 7 through the DRC I get the error "unable to connect to the gateway terminal server."

  problems of the DRC of vista for windows machine 7

  I have 2 computers running on a homegroup. When you try to connect from my vista desktop to my laptop windows 7 through the DRC, I get the error "unable to connect to the gateway terminal server."   Can I remotely from the laptop to the desktop vista end. I the DRC 7 is installed on the desktop and tried to connect using the IP as well as the name of the machine but still no joy.

  can someone shed light on this please?

  Hello

  Temporarily disable the security software on both computers and check if it makes a difference.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.