USB Universal Host Controllers - Windows 7 Ultimate edition. Does not properly

Similar Questions

• Windows 7 Starter Edition does not recognize a hard drive WD

  Windows 7 Starter Edition does not recognize a hard drive WD, I used until last month. Device Manager sees it, he sees the USB controller (it lists as a mass storage device), but I can't access the information on the hard disk, or make use of the last backup. I tried to uninstall USB drives - it is not the thing. It gets listed under disk drives.

  Thanks for the reply.

  There was no error message: the device has been recognized (listed) by the USB controller and the Device Manager, but not by the management of the disks - so I couldn't access.

  I managed to fix the problem after:

  -J' scanned the computer (DELL Inspiron) with the Safety Scanner
  -J' completely uninstalled all the software associated with an external hard drive
  -J' uninstalled the USB controllers
  -reboot the system
  -reconnected the external HD
  -After gaining access to the drive, I installed the dedicated software

  Best regards

• Driver Ethernet for Windows XP Home edition does not work on Satellite A100

  Satellite A100-784 PSAANE-02L011G3 ethernet driver for Windows XP Home Edition does not work. Cannot successfully install driver, downloaded all the drivers and still does not.

  As a sign of Device Manager yellow. I bought my laptop with Vista BASIC and I put XP - SP2. Country is Croatia! Help me please!

  Hello

  I can't believe that you are not able to install the LAN on this Satellite A100 driver!

  However, the satellite A100-784 supports a chip 82562GZ Intel 10/100 Mbit (Ekron) of Lan.

  If you want you can download and install page Intel network driver:

  http://Downloadcenter.Intel.com/Product_Filter.aspx?ProductID=999&lang=eng

  You will find the drivers Intel 8256 x Ethernet controllers

  Good bye

• Windows Vista Ultimate Edition will not be upgraded to Windows 7

  Windows 7 Upgrade says he cannot directly upgrade Windows XP, duh?  I ran the Upgrade Advisor before running the upgrade software and did not get this stupid message. I get only when the software upgrade performs its checks.  I am running Windows Vista Ultimate Edition with all updates to September 24, 2013.

  Which edition of Windows 7? It matches the edition of Vista you are trying to upgrade to?

  When important changes to your computer, for example an upgrade, it is always recommended that you back up your system before installing a new version of Windows. In your case, you can upgrade to Windows 7 depending on the edition and the architecture of Windows Vista, you have installed. If you are running a 32-bit version of Vista and upgrade to a 64-bit (Windows 7 edition) version, you'll have a pure make install, it is the opposite case.

  If you are using Windows Vista Home Basic or Premium consumer editions, you can only upgrade to Windows 7 Home Premium or Ultimate. In addition, you can make downgrades, which means, if you are running Windows Vista Ultimate Edition now, you cannot downgrade to Windows 7 Home Premium. You perform logical upgrades:

  Windows Vista Home Basic > Windows 7 Home Basic, Premium or Ultimate

  Windows Vista Edition Home Premium > Windows 7 Home Premium or Ultimate

  Windows Vista Business > Windows 7 Professional, enterprise or ultimate edition

  Windows Vista Business > Windows 7 Enterprise

  Windows Vista Ultimate > Windows 7 Ultimate.

  http://www.notebooks.com/2009/10/07/how-to-upgrade-to-Windows-7/

• Windows XP Home Edition does not load in any mode after reboot to uninstall Norton

  I wanted to get rid of Norton anti-virus, then, I have downloaded and run the Norton Uninstaller. After what seemed an eternity he finished and asked me to restart the computer to complete the uninstalation. I clicked the botton "Restart now" and after the screen, which shows the bios is nothing. No loading screen, no beeps or anything else, just black. In addition, it does the same thing in all modes.

  I removed the HDD and an IDE to USB for connecting to my mobile backup (Win7 Ultimate) and performed a virus with TrendMicro Titanium antivirus scan + and scan with malewarebytes paid version maleware. No virus or maleware found. So, I ran a check/repair through backup with no found error disc.

  I do not have a XP or 7 CD repair/install, nor am I money right now. I really need to get going again.

  Infected computer:

  Compaq Presario M2000

  Windows XP Home Edition SP3

  Processor Intel Centrino Pentium M 1.5 GHz

  1 GB of RAM

  Intel Extreme Graphics 2

  Machine backup:

  Dell Inspiron 1501

  Windows 7 Ultimate Edition SP2

  AMD Turion 64 MK - 36 2.0 GHz

  3 GB RAM

  Integrated ATI Radeon Xpress 1150

  Looks like you somehow corrupted the bootloader.

  If I'm not mistaken, you can technically download disc for Microsoft Windows XP SP3 OEM HOME legally, as long as you use your current license.

  You can also communicate with Compaq and request a repair disk.

• Aspire V3-771 Wireless Windows 7 Ultimate edition will not return to the factory settings

  Hello everyone,
  so I'm having to V3-771-6601 laptop which I bought in the US 2 years ago. I have some kind of virus which was activated immediately after the sign in. Some photos of Interpol appears and they wanted to charge a fraud or something like that. I tried to press CTRL + ALT + DEL to task mngr, but the virus won't let me. So I entered in safe mode and saved all my valuable information. The laptop has windows 7 Home Edition. I decided to install W7 Ultimate RTM. So when I was doing that, I formatted ALL partitions that I saw on the screen. After that i have PXE boot problem. I realized that I need to connect my lan cable. Ok. After that the computer does not start, it shows just acer splash screen and immediately restarts again and again and again. I tried to click ALT + F10. At the bottom left, I saw "switch to erecovery" or something like that. After pressing alt + f10 there is a '_' in the upper left corner, and the Frank is frozen. So I can't even boot to see victory logo, even I can't return my phone to factory settings. Just to note I have no CD with my PC, only the power chords and that's all. The House of win 7 was already languages. Please guys help me how to fix my laptop.
  Best regards

  Well, you could have done your own recovery discs when you bought your PC!

  I agree that it is a shame that you can't get a copy of the disks where you live!

  If you are happy to have a cracked version of Windows, it is to you. Even if you can open a Pandora's box, we'll agree disagree on the question

  As for the problem of button, it could be a sign of a faulty keyboard or it could be a software problem. A few copies of cracking are so changed, it could be an error in the code!

  You can try and run a Linux live disk to see if it happens there. If so, then the keyboard will be replaced.

• recovered to previous windows because of an error during the installation of an upgrade of windows 10 now my windows 7 Ultimate edition is not enabled

  before installing an upgrade to windows 7 ultimate windows 10. my version of windows has been activated and genuine. but due to an error when installing windows 10, blue screen appeared and my pc was recovered back to the previous version which is windows 7 ultimate but now its true this is not enabled and im nt able to upgrade to windows 10 as well...
  in the system properties it says 3 days to go to automatic activation I waited for 3 daysbut it said another 26 days to automatic activation.
  What does that mean?
  How can I solve this problem?

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the report produced by the MGADiag tool

  (download and save to the desktop - http://go.microsoft.com/fwlink/?linkid=52012 )

  Once saved, run the tool.

  Click on the button continue, which will produce the report.

  To copy the report in your response, click the button copy in the tool (ignore the error at this stage), and then paste (using r-click and paste or Ctrl + V) in your response.x

  -in your own thread, please

  Please also state the Version and edition of Windows cited on your COA sticker (if you a) in the case of your machine (or inside the battery compartment), but does NOT quote the key on the sticker!

  http://www.Microsoft.com/en-us/howtotell/hardware.aspx

• Satellite Pro S300-11Y - downgrade from Windows XP Home edition does not work

  Hello

  I have a SAT PRO S300-11 since January 2009. It came with CD to downgrade to Windows XP, and I did several times over the years without any problem. But now I do and what finish to downgrade, when done last reset, windows starts to have problems and doesn t work.

  But if I do not the last reset on arrival of the downgrade the machine works perfectly, but when I do reboot then when windows starts it works. I try 5 times and still the same. I come back to windows original vista (I did CD to do) and it happens the same problem.

  Any help greatly appreciated,
  Thank you and sorry for my bad English.,.

  Jordi

  My English is not so perfect, but to be honest, I don't understand you.
  Do you mean by reset? Do you mean, finally, restart?

  By default the BIOS settings and try to reinstall Windows XP Home edition recovery image.

• Satellite C660-108 - Windows XP Home Edition does not install

  I try to install Windows XP Home Edition on a Toshiba Satellite C660-108, without success.

  I changed the BIOS disk in "Compatibility" mode (what is the same thing as "Legacy IDE"?) by following the instructions on a Yahoo Answers question on the same issue.

  What has improved the situation, in what I now get an error message a few minutes after installing XP said "Starting Windows" instead of immediately after. The error message is the same that I have already received and is as follows:

  "A problem has been detected and windows has shut down to prevent damage to your computer...". "Technical information: * STOP: 0x0000007B (0xF78D663C, 0xC0000034, 0x00000000, 0x00000000).

  Thanks in advance for any help,

  Luke

  PS - I'm a mac user and do not have much experience in the use of Windows laptops, so I need instructions spelled out clearly enough if possible.

  The error could be related to drive HARD and the setting in the BIOS of the controller...
  Probably, you need to install Win XP using SATA AHCI mode and to add the driver SATA as described here:

  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm
  http://APS2.toshiba-tro.de/KB0/SPD4603LT0000R01.htm

  I found a similar description in the MS forum:
  http://answers.Microsoft.com/en-us/w...4b511ed?auth=1

• Windows XP Home edition does not charge up - screen Toshiba and then nothing

  I opened my computer to stand by earlier. And received an error message such as:

  WINDOWS CANNOT CONTINUE RUNNING BECAUSE THE FILE IS DAMAGED AND UNREADABLE...
  Then he had a countdown until it restarted. After the computer restarted (loads of screen toshiba upwards) then nothing happends. I managed to get into the safe mode start page, but when I select start in safe mode, it does nothing, actually freezes. Seems that the problem is with XP.

  I also tried to "last good configuration" but who also refuses to load.
  I can, however, in the BIOS.

  The black and white background writes startup screen that flashes briefly upward when after that the toshiba screen doesn't even come to the top.

  I have a P100-429 Satilite using XP SP2 (or 3) does not remember.

  Is this a hardware problem? I lose data?

  I am aware that my system was clean and I was using a good anti-virus.

  Please please let me know if you have any suggestions or comments.

  Thanks in advance, Max...

  Hi RisSsky,

  you are in a deep deep sh... t... No. not really...
  Looks like the filestructure hard disk is damaged.
  the hard drive is recognized by the bios? means, it is listed as a device?
  There is a sound of the hard drive? scratch or buzzing or ticking?

  CHKDSK may help, but I would 'safe mode' where you want not to lose data on disk.

  don't panik, we will do things.

  2 options to solve this problem:
  the first and save:
  -Remove the old hdd (you need later)
  -get a new hard drive and make a recovery/installation on the new drive.
  -also get a usb - hdd connector to access old data hdd and copy on the new disk.
  or the 2nd:
  -run chkdsk on your hard drive, maybe you need to do this with a "live-system-on-cd.
  Be aware that if there is a problem it will get worse...
  -start in safe mode

  If you're lucky, the 2nd option will do.
  as said before I'd do it "the safe way.

• My product key of windows xp home edition does not work?

  Good while my laptop was a major virus, so after 5 antivirus, antispyware programs could not locate or get rid of it, I had no choice but to re - install windows xp home edition. But the problem is that my product key does not work. Why is this and what can I do, I don't have money to buy another computer laptop/product key

  Dell inspiron 6400

  p.s the guarantee expired already tried that one.

  In this case, you are probably using the wrong type of disc.

  You MUST use an OEM disc with an OEM key in WIndows XP

  You MUST use a disk of Windows XP Home Edition with a WIndows XP Home Key

• Windows XP Home Edition does not start: System Configuration Error Code purple?

  I ran recently on my Windows XP Home Edition SP3 computer system recovery and once the recovery is finished I rebooted the system and then this message and I'm stuck here.

  I don't have any disc that came with the computer because it was very long ago already. I tried to download the 'Home Edition Set Up disk for Floppy Boot Installation of Windows XP"Microsoft, but I can't launch the ff:

  Windows XP Home Edition
  Windows XP Home Edition SP1
  Windows XP Home Edition SP2

  I can't create the configuration of disk for home edition, SP1, and SP2 because this computer I use currently is a 64 bit and no floppy drive. That's why I downloaded this instead:

  Windows XP Service Pack 3 - file to Image CD ISO-9660

  From:

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=2fcde6ce-b5fb-4488-8c50-fe22559d164e&displaylang=en

  I burned a DVD ROM, but I don't know what to do next. After burning, I reinserted the disc to your computer from the active autorun. Then I inserted the disc for my Windows XP that has "System Configuration Error" and I tried to restart it but theres just no autoplay or anything that the computer always crosses the "System Configuration Error" message and I don't know how to access the set up disc. What should I do? Help please... :(

  Hello

  Try the methods listed in the section below and check.
  How to resolve configuration errors by using the System Configuration utility in Windows XP
  http://support.Microsoft.com/kb/310560

  How do I recover from a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

  I hope this helps.

• Windows 7 starter edition does not recognize HP LaserJet 1536 dnf printer

  I use the Acer Aspire one 521 netbook with pre-installed windows 7 starter (it was bought with Win 7 starter). I have the HP LaserJet 1536dnf printer. I install, it worked well, but every time that I unplug the usb cable from my netbook and plug it in again, windows does not recognize the printer (but oddly enough, regognizes the scanner). So is it possible that I should not install/uninstall the printer each time I plug/unplug the printer?

  Hello

  1. What is the exact error message you get?

  2 did you a recent software or changes to the material on the computer?

  Method 1:

  Run the tool material and devices and check to see if that fixes the problem:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  I also suggest to go through the steps from the link provided and check.

  Method 2:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope this helps and keep us posted.

• Windows 7 starter edition does not work with Java 7 (unable to load the chat room) how to fix?

  Hello

  I have Windows 7 edition - starter and Java 7 when I try to use a school chatrooom - java won't load properly - tech school says it's because Windows 7 does not support Java 7 - any ideas on how to fix?
  THX,
  Maja

  If he believes that the school needs to get a new technology.

  To check if the problem is that the cat does not work with Java 7, uninstall Java 7 and install Java JRE 6 from here:

  http://www.Oracle.com/technetwork/Java/javase/downloads/index.html

  You must specify the exact error messages see you or post links on the screenshots so that your problem can be better understood.

• See 4.6 Client installed on Windows 7 Home edition does not connect to the Manager

  Dear friends,

  I just joined this communitity, need help with a small problem of debugging that arrested me in the track.

  I recenty view upgrade 4.5 to 4.6 view, upgrade some services don't prevent not problems, but I have overcome by reading the blogs on the internet. After the upgarde I can't connect to connection Manager from the view of my Client to view 4.6 - Vesrion - 4.6.0 366101. Only thing I can think that my view client 4.6 is installed on Windows 7 Home Edition. But I had no problem connecting to the connection manager when I saw 4.5 client installed on the same workstation.

  Any help will be much appreciated...

  In VMware View Administrator go to

  Display Configuration > servers > discovers the connection to the server > edit.

  Uncheck the box for «use a tunnel connection is secure on the desktop»

  then restart the view connection server service