WAP54G and new modem

Similar Questions

• BEFSR41 and New Modem/router DSL

  Verizon has recently replaced my DSL modem with a new DSL modem/router with a dynamic IP address. Even though I have full internet access with the new modem of the Setup for my Linksys BEFSR41 router disk will not be connected to the internet. What should I do for the new modem so that the Setup disk will see the internet? The DSL modem/router has only one port so I'm not able to have more than one computer/device hooked up at the same time so I still need my router.

  Well how about you that :-) It all works now. Thank you guys.

  Dale

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• Time Capsule and new cable modem

  I currently have one Capsule of time hooked to my ATT 2Wire modem/router. I think that the TC is configured in Bridge mode. I'm getting rid of ATT and get an another cable operator to install internet. I'll use an ARRIS modem. What is the process to reinstall the TC to the new modem. Do I have to "reset" the TC to the factory setting, then set the TC as "new". How can I do this? I lose all my Time Machine backups?  Thank you!

  What is the model number of the "modem" Arris that will be installed?

  We ask... because with good luck..., you will not have to make any changes of the Capsule of time... just plug it in.

  With not so good luck..., you will have to just start over and implement from scratch time Capsule.  You will not lose your backups, but it would be nice to avoid the start process all if possible.

• I have a new modem and you want to configure my Apple Airport as a backup drive; How do I do that?

  I have a new modem from Verizon and want to configure my Apple Airport as a backup drive; How do I do that?  I need to extend the network, simply find a use for the airport.

  What is the brand and model of your new modem from Verizon? What is the exact model of your airport?

• DeskJet 6940: ethernet connection between the new modem and printer does not transmit Mac

  I just installed a new modem to Qwest; It works wirelessly with my iMac 10.11. My old (but functional until yesterday) Deskjet 6940 is connected to the modem via Ethernet. When I try to print, the document seems to be transmitted to the printer, but then it hangs on and I get the message "the printer is not connected" - which it is, plugged, ethernetted, and set in motion. Support of Qwest says that only 10% of the info from the computer are the printer, but he seems to think that the part of the new modem Ethernet is functional,

  I have already tried all unplug/restart/send/add printer new check/updates / IP (cannot connect) / ethernet ports and cables, etc.

  Any other ideas?

  Thank you!

  Hi @newgranny,

  Thanks for getting back to me.

  It is good that the printer has been able to print a diagnostic page.

  Ensure that the router and firewall on the market do not block these ports.

  • About the application firewall

  Ports of printing:

  • UDP ports: 427, 137, 161
  • TCP port: 9100

  Card photo upload:

  • UDP ports: 137, 138, 427
  • TCP port: 139

  The HP device status:

  • UDP port: 161

  Ports of Web Services:

  • UDP and TCP: 80, 443, 5222 and 5223

  Hello Ports:

  • TCP and UDP: 5353 and 5297, 5298

  Unplug the wired network (ethernet cable), restore the default values on the printer.

  Restore the default settings.

  Follow these steps to reset the printer to factory default settings:

  1. check that the printer is on.

  2. press and hold down the button to report Page.

  3 while holding down three times the homepage button, press the Cancel button.

  4. release the report Page button.

  Source

  • Restart the printer.
  • Connect the ethernet cable.
  • What were the results?

  If the problem persists, try the USB connection.

  Please reply to this message with the results. Good luck!

• I got a new modem and the router and now I can't print wireless.

  I have a Photosmart 8450 printer.  My operating system is Windows7.  I tried to follow the Scan doctor, but I guess I'm not tech savy enough to understand.  It worked fine before the new modem and the router.  She is 'offline' and I can't understand how to put line.  Thanks for any help and easy enough for me to follow.

  Hello raedene715.

  Thanks for the transcript, it was useful.

  Please, check the network cables and connections (side of the printer and router). If possible, try a different network cable.

  See you soon!

• Problems with the new modem DSL and Linksys BEFSR41

  My Speedstream modem died and I had to buy a new modem.  At this time of year, it is difficult to find exactly what I wanted and I ended up buying a D-Link DSL - 2320-B.  I got the Linksys BEFSR41 (old version 1, I think) for years and it has always worked well.  I have problems to get an internet connection through the router.  With the modem connected directly to the network card, as now I have no connectivity problem.  I had to change the IP address on the Linksys BEFSR41 192.168.2.1, as the modem is 192.168.1.1, 192.168.0.1 as the old Speedstream.  I couldn't see a way to change the IP Address of the new D-Link.  I have my ICS TCP/IP set to auto obtain IP and DNS.  I was previously created for a fixed IP of * provided by the router.  Even with the setting on the router to "Obtain an IP address automatically", I can't to the internet with the router in the middle.

  Any help will be appreciated.

  Your modem is a combination of the modem and the router. The problem occurs when you try to connect another router behind this configuration and end up having 2 servers dhcp and nat 2 (for port forwarding and other issues, creating in some cases where even branded products use ip addresses will clash and devices will not connect at all when him are interconnected).

  To avoid the situation described above, it is recommended that you enable the full Bridge mode on the modem / router that you currently connected to the internet and let your new wireless router controls all the functions within your local network and the internet connection (you must enter all the details in the new router, including Internet service provider username and password).

• I changed to a new modem, and now my speakers do not work, I unplugged and back is connected.

  My modem is gone blouie and I got a new modem installed by my provider, since this has been done I have no sound coming from my speakers, the power light is on, I unplugged them and they plugged back, still no sound, help!

  Hello

  Perform the following methods and check:

  Method 1:

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-XM/Windows7/tips-for-fixing-common-sound-problems

  Also run the fix from the following link and check.
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Method 2:

  Open the troubleshooting of Audio playback
  
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  Let us know if it helps.

• I am using windows 7 and my computer laptop wifi does not connect to the modem. It worked correctly with the other modems. I had the prob with the new modem provided by optus. can someone help me please?

  my computer laptop wifi works with other modems. and my modem works with other laptops. they have one problem with each other.

  I don't know why, please help me...

  Hello Omar.

  Thank you for keeping us posted.

  It seems that you did not try the method 2 and 3 after running the troubleshooter from network. Please, try it both ways and see if that solves the problem.

  Reply with the results. We will be happy to help you.

• How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to work with this pinhole?

  Usually a paperclip or toothpick or ball pen.

  Stick it in the hole and reset for about 10 seconds until the front led flashes quickly.

  How to reset AirPort Extreme 10.11.6 OS?

  The software method... Unlike the above material method... is to open airport utility and select restore default settings.

  

  Both methods take you to the same place.

  You can also read the manual...

  Reset to a base station AirPort FAQ - Apple Support

• Xfinity triple play requires new modem?

  I have a Motorola model surfboard SB6120 I bought to use with the airport. Now I upgraded to Triple Play and Comcast told me I need a new modem or the service will not work. Is this correct? I assumed that if I buy the ARIS they recommend so I no longer need Airport?
  I read the reviews of the modem that it was difficult to set up etc and don't want to buy a new modem, if I don't have to do.

  I know just enough to know that I don't know about all that stuff. So in your reply, would you mind ' dumbing down there? " Thank you!

  Susan

  Comcast told me I need a new modem or the service will not work. Is this correct?

  That would be a question of Comcast with Apple support.

  I assumed that if I buy the ARIS they recommend so I no longer need Airport?

  What model number of the Arris product they recommend?  (Arris offers more than a dozen different products)

  If you get a 'simple' modem, as the SB6120 you have now with only a single Ethernet port at the back of the unit, then you will always need airport to act as a router.

  If they recommend a type of device that combines a separate modem and a router separate in the same package, then you are probably the most convenient airport... but you can still use it if you want to "modem/router" or "gateway".

  You have two wireless in this way, you may not need.  Some users use a network to their 'private' network and then use another wireless for the 'guests'... so it does not give the password to your private network.

• Airport Extreme and Broadband Modem/Router

  I have my Airport Extreme (5th generation) plugged into a Broadband Modem/Router combo. I would like to have both able to use their wireless capabilities. The Airport Extreme has been previously connected to a Modem broadband all my IP addresses came by Airport Extreme (192.168.2. *). With the New Modem/Router combo broadband, it uses 10.0.0 * so I would be able to use Airport Extreme to add the 192.168.2. * While having the 10.0.0. * the Broadband Modem/Router combo.

  Is this possible and, if so, how do I configure Airport Extreme to do?

  Normally, you don't want two devices on the same network as the two try to act as routers to the same network. Which will produce conflicts of IP addresses... which can possibly be addressed... and a Double NAT problem, which cannot.

  The Double NAT error can cause a number of unpredictable issues... things like the problems of communication between the devices on the network, slow navigation... or, not navigation in the case of certain websites, Internet access slower, to name a few.

  Yes, some users may get away with a Double NAT on a single home network, but unnecessarily complicating things over a network is normally something you want to avoid.

  We do not recommend it, but if you really want AirPort Extreme for use range 192.168.2.x however, you can easily make this change using AirPort Utility. If you are not sure how to do this and need help, then we will need to know which version of AirPort utility you are using.

  To find, open AirPort Utility, and then click the menu of AirPort Utility in the far left of the screen corner. Click on about AirPort Utility to see what version you have and post back with that info.

• installed a new modem router now I can't access my emails with my usual password.

  I have installed a new modem router, a Netgear D6300, now when I press the messages button get on my email account thunderbird, he invited my password which is normal. But when I enter my password that worked all the time it tells me that it is the incorrect user name or password. Of course, the implementation of my new router has changed something, please help.

  almost all Netgear routers have a firewall. Then log into the router. username Admin and password is probably password. If not these days they printed on the bottom of the router. Check the ports used for mail are not blocked.

• Service (search) and N ° imei and empty Modem firmware

  Hello world.
  I use the iPhone 6 more. This morning, I used like normal, but he has a problem while I'm closing 4G data it shows not the search in the bar service.
  I tried to restart the phone with Home & power button, also I tried to reset the setting also but it stays the same. I was getting ready to restore in iTunes but when I check the imei number, it's no imei in the list and Modem Firmware is empty. But the phone still as usual as the Wifi and the application that it no service does not (research).

  My question:

  1. How can I retrieve the Imei and the Modem Firmware number and use it as usual?
  2. now my phone it works always, what will happen if I try to restore or upgrade to new iOS in iTunes?

  Please help me solve this problem. I really really sad and don't know what to do now! also, I have no money to change :-(

  Hello

  If your SIM card has been blocked, check with your network provider?

  See you soon

  Brian