Windows won't go into standby mode.

Similar Questions

• T1530: DJ T1530 won't go into standby mode

  Hello

  We just bought a printer, DesignJet T1530 but we are facing a problem: printer will not go into sleep mode... and is very noisy (blowing fans)

  We put it up to 5 min, tried other times without success.

  Does anyone has a tweak?

  Thank you for your help.

  firmware: MRY_04_02_00.5 (will try the last of them but no indication on this issue in the release notes)

  SOLVED

  First of all, I tried to disable the internet functions without success.

  Have updated the firmware from MRY_04_04_00.4 and I appreciate very much the printer now in mode 'sleep'.

• my iphone won't go into standby mode

  I recently bought an iphone SE.  Recently, I noticed that my phone will not mode when connected to usb or power standby. The screen just goes dimmed, but does not go to sleep mode

  Is this normal?

  THX

  "Sleep" mode should make the display turns off. Is - this just dim halfway? If so, it is not normal.

• Printer won't go into Standby Mode

  I just bought printer e-all-in-one HP Photosmart 7510 - C311a, and constantly when my Mac that works on OS X starts in mode 'sleep' the printer sounds as if it is being initialized.  It also has a message on the screen to turn off the unit to avoid damage.  I do not understand, this printer is a 'sleep mode' too?  I don't want you must manually activate it offshore, but he makes too much noise until the mac is turned back on.  What should I do?

  Is the printer plugged into a power strip or surge protector?  If so, plug it straight into the wall.

• WSD Print device device driver prevents computer from going into standby mode

  WSD Print device device driver prevents computer from going into standby mode

  This message indicates that the computer was unable to fall asleep by a device driver.

  Look for the drivers updated printer manufacturers website or run the Microsoft Fixit:

  http://support.Microsoft.com/GP/printing_problems

• I have the latest Windows Live Mail 2011, but when standby and locks system, the only way out is to do a complete or end of Windows, restart then go into sleep mode. This never used to happen until Windows 2011 has been upated in my PC.

  I forget always at the end of the lIve session of Windows before you put it in standby mode, the PC appears and then lock properly said, in response to anything, so I have to do a reboot complete, very annoying.

  Also when working within Windows 2011, if you add a lot of attachments to an e-mail, I have often to do and then send it, the list of attachments disappear off the screen, so when you send you do not know really which was transmitted, horrible situation, so you must include send to yourself, then you can check what has been sent. Stupid!.

  How can I get rid of these flaws?

  You will find support for Windows Live Mail in this forum: http://windowslivehelp.com/forums.aspx?forumid=b91657c9-9031-4406-a398-7d0783119bb7

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Windows XP go into standby mode

  When I click on the icon the computer shutdown ensures he begins to go into sleep mode and then turns back on. I can hibernate the computer or stop it but not in standby

  Can go into the Hibernate mode, but not the sleep mode so use Hibernate

• My printer interrupts communication with my PC when the P.C. goes into Standby Mode. Why?

  Until yesterday, the printer worked fine.  There is no cable or hardware change any.  I am running Windows XP with a jet of Lexmark color printer.

  When I restart the printer works fine.  However when the order goes into standby or hibernation mode, I can print is no longer when the box comes back active.  I get a message that "there is a communication error with the printer.  To correct this problem, a box appears I should go to start/settings/printer and make sure the "Enable bidirectional support" box is checked.  Unfortunately, I can't access the settings of the printer directly from the start menu.

  However, if I click on 'Options' that is displayed when the printer stops and I click "Troubleshooting", I don't see that the "enable bidirectional printer media" is more verified.  If I check, I get a message saying "printer is busy".  If I click on start again I get the same message and the "enable" box is unchecked.  If I hit Cancel, the box is also disabled.  I enter a loop that does not end.

  Any ideas how I can access the printer directly from the start menu settings?  Or how to prevent the impression of no longer communicate with my PC when it goes into sleep mode?

  Thank you much, long in advance for any suggestions you may have.

  It is a Lexmark Z-52.  After 8 hours of trying many different, including the link ideas that you suggested, I have determined that as a result of some recent Microsoft Download, the printer would work only if I used the Dell printing device incorporated in the installation software.  If I tried to install the Lexmark printer from the installation disc, I got the persistent problem.  I deleted all but access to the printer through the installed also origin and everything of fine.

  When I need to change the cartridges and align the jets, I install the Lexmark program, align the print cartridges and then remove the program Lexmark, using the default value of Dell for the printer remaining.

  It works, but why I had a problem, I don't know.

  TNX for the comments!

  Big Phil1

• Satellite 1800-314: when I close the lid it won't go in standby mode

  I hope someone can help.
  I recently had my Satellite 1800-314 (Windows XP) re-formatted and now when I close the lid he's going to sleep... the power light flashes orange, when I opened the lid still once, Windows stops and then restarts. I tried to install the Toshiba power settings, defining "when I close the lid, in standby mode", does not.

  Have uninstalled then Toshiba power settings and all the settings of ordinary power in the Panel of 'sleep', etc., but it REST did not return to standby mode.
  I'm tired now.
  Is there a simple solution that I'm missing?

  Grateful in advance for any help!

  Hello

  You know it's very important to install drivers in the correct order.
  The installation of common modules at the beginning is important because some drivers of Tosh need this application to work properly.
  If the energy saver has been installed on the operating system windows power settings will not work.
  Toshiba crash parameters the parameters of Microsoft.

  In addition, please check your BIOS preinstalled. Compare the version with the BIOS on the page. If your uses of the unit the old version, so try to update.
  But be careful. You must use the good BIOS and the right procedure upgrades.

• Windows Recovery screen appears after "standby" mode

  Hi, I have a Toshiba Satellite C660 laptop. The problem is with "standby" mode, reactivation, the windows to the recovery screen appears as if the computer was arrested by force. Any help would be great!

  There was a faulty driver installed, I uninstalled and solved the problem! Thank you for your time!

• ESX Server won't go into maintenance mode - Timeout

  We have 1 host ESX 4.1 support our view desktop computers. I tried to plan a reorganization of the host during the night, but jobs would not be the exit ramp leading to the maintenance task timeout mode.

  What will do to make desktop computers will be exit during this upgrade? I put all the desktops into maintenance mode before the host trys to remedy?

  Thank you

  Travis

  This part of a cluster DRS ESX Server? If not you will need to manually stop or vmotion the VMS to another ESX host before it can go into maintenance mode - if it's part of a DRS DRS cluster must be set fully automated so DRS can automatically vmotion the VMs before entering maintenance mode.

• Windows 7 computer goes into Sleep Mode while the activity of the system

  Hello, I have windows 7 premium.  I think there may be a bug that needs to scan, my system goes to sleep while there is the activity of the system.  For example, when downloading a file, do a virus or by post where analyze or defragment.  I believe that the year 2010 are the operating systems with the smart enough so that the system is active and goes to sleep during execution of these programs are active.  Can someone tell me if this is a bug or suggest software to keep the system awake while 'X' program options is actively running, for example if I do a defrag of HDD, I don't want to change power if the computer is running all night, only for 2 or 3 hours that the scan is running Once the program ends defrag'ing the systemit should then wait for the time set in power options and stop.

  Hello
   
  If there is no interaction from the user to a certain amount of time, the computer goes into a sleep mode was
  application runs in the background. This isn't a bug. You may need to change the settings for options of power as a result.

  Sleep and extended: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions
   
  Change, create, or delete a power plan (scheme)
  http://Windows.Microsoft.com/en-us/Windows7/change-create-or-delete-a-power-plan-scheme

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows do not go to standby mode after being left idle

  Windows 7 Home Premium, Dell Inspiron 1545 laptop

  My laptop won't sleep after be left idle.

  I checked all power options, including allowing the laptop to sleep when sharing multimedia. I checked the Device Manager for hardware that can wake up my laptop. There are no programs that are listed etc..

  When sections of battery, in that the critical level, my laptop will put into hibernation.

  I am currently using power options that don't work by default energy savings.

  I'm pretty sure that my laptop used to go to sleep with Windows 7 installed, but have no idea what has been changed and don't like formatting etc.

  It makes me crazy... I'm not a novice in computer and googled, I tried many different options etc.!

  Thanks for any help.

  I managed to fix this now.

  My audio driver (IDT High Definition Audio CODEC) observed an open audio stream, preventing sleep. Downloaded and installed the latest driver well.

  I discovered this by using "powercfg-applications" command at the command prompt.

• Windows hangs on past in standby mode

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello... Apply online to object... anyway...

  Click Start-> settings-> Control Panel-> power-> advanced options. Uncheck "Prompt password when the computer wakes from sleep mode".

  Hope this will help...

• cannot go into standby mode automatically only manual

  How can I get my computer to go to stanfby automatically

  Hello
  From > start / Control Panel > settings > Control Panel, open Power Options then power management. Select the desired settings for standby and hibernation. OK your way out.

  Hope this helps,
  Don