With a dynamic IP address DMVPN spoke

Similar Questions

• VPN spoke with dynamic IP address / DMVPN

  Hello

  Would you please help me on this:

  What is the cheapest Cisco router for a desktop environment 10 to 20 employees that supports DMVPN or any other technology to maintain a permanent IPSec tunnel, not question that the provider of services at this office only allows dynamic allocation of IP address?

  I know about 2801 and 1841, but is it possible to go even lower?

  Kind regards

  Mladen

  We use the Cisco 871 ethernet router and have a lot of success with this router using DMVPN.

• L2L dynamic peers with no dynamic peers

  Hi all

  Can't see to fight my way out of this configuration.  We have a router configured with the dynamic IPSec L2L counterparts and remote access to (pretty much using this configuration: LINK ).  I'm not use to the keychain / configuration profile.  But try adding a tunnel without a profile, perhaps 'non-dynamique' peer?

  Here is the configuration:

  crypto keyring spokes 
  pre-shared-key address 0.0.0.0 0.0.0.0 key PSK1
!
crypto isakmp policy 10
 encr aes
 authentication pre-share
 group 2
!
crypto isakmp policy 20
 encr 3des
 hash md5
 authentication pre-share
 group 2
crypto isakmp key L2L-PSK2 address 76.113.24.103
crypto isakmp keepalive 10 10
crypto isakmp nat keepalive 10
!
crypto isakmp client configuration group VPN-Users
 key PSK1
 pool ippool
 acl 171
!
crypto isakmp profile VPNclient
   match identity group VPN-Users
   client authentication list default
   isakmp authorization list groupauthor
   client configuration address respond
crypto isakmp profile L2L
   keyring spokes
   match identity address 0.0.0.0    
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac 
crypto ipsec transform-set transform-1 esp-3des esp-md5-hmac 
crypto ipsec transform-set testset esp-3des esp-md5-hmac 
crypto ipsec transform-set ESP-AES-SHA esp-aes esp-sha-hmac 
!
crypto dynamic-map DynIPSecMap01 2
 set transform-set ESP-3DES-MD5 
 set isakmp-profile VPNclient
crypto dynamic-map DynIPSecMap01 5
 description tunnel_to_EEUU
 set transform-set testset 
 match address 110
!
!
crypto map IPSecMap01 10 ipsec-isakmp 
 description REMO_ST_VPN
 set peer 76.113.24.103
 set transform-set ESP-AES-SHA 
 match address REMO_ST_VPN
crypto map IPSecMap01 10000 ipsec-isakmp dynamic DynIPSecMap01 

  interface Serial0/0/0:0
 ip address 178.31.76.1 255.255.255.252
 ip flow ingress
 ip flow egress
 ip nat outside
 ip virtual-reassembly
 crypto map IPSecMap01
 
ip access-list extended REMO_ST_VPN
 permit ip 172.18.38.0 0.0.0.255 172.16.202.0 0.0.0.255
!
access-list 10 permit 65.122.15.2
access-list 110 permit ip 172.18.35.0 0.0.0.255 10.1.2.0 0.0.0.255
access-list 110 permit ip 172.18.38.0 0.0.0.255 10.1.2.0 0.0.0.255

  We are failing on Phase 1 because the PSK does not match.  And this error:

  ISAKMP: (3134): key not found in the profile key, abandonment of exchange rings

  Can someone point me in the right direction?

  Thanks for your time and support,

  Nick

  Try to create a new crypto isakmp profile to match the INVESTIGATION period off the coast of the L2L counterpart.  Then create a new door-key crypto for this peer instead of using the command "isakmp crypto key.

• VPN tunnel with IP dynamic

  Question:

  Is it possible to install a GRE tunnel between two routers, one that has a dynamic IP, the other has a static IP address. If this isn't the case, GRE, is there another tunneling protocol we could use?

  In the search for setting up a VPN, I found that the way suggested to do is a GRE tunnel, so that dynamic routing work via VPN. We do not use dynamic routing, but I want the flexible design for future changes that will occur.

  Our facility is:

  2651XM (hub) to the corporate office (static IP). DS-1

  827H (spokes) to each branch (dynamic IP via DHCP). ADSL.

  IOS version 12.2 (13) T supports Multipoint GRE function which will allow your GRE tunnel on the side of ADSL to use a dynamic IP address. Locate the CCO love and documentation DMVPN (dynamic multipoint VPN).

• Message came up with, "Windows has detected another computer with the same IP address on this netework."

  A message came that said, Windows detected another computer with the same IP address. "... or similar message to one, that could just be the functioning of the laptop for the wireless?

  MurrayJoe:

  > Mean someone has or may have access to my PC or laptop?

  You mentioned a wireless laptop. Do you get this message at home (when your laptop is in communication with your own wireless router), or that you get this message when in a public hotspot?

  If at home, then I would be not too concerned (what security options enabled in your home router?).

  If you get the message while using a public access point, this does not necessarily your computer has been hacked... but it is a warning that you should not ignore. In general, I would not go to any site that has my financial data, or any other sensitive data, a public hotspot. There are too many ways that a public hotspot may be compromised.

  Your original post said that "a message came that said, Windows detected another computer with the same IP address.

  There are several reasons this could happen... some innocent people and some not so innocent.

  If your network is configured for the most common way, then your router uses a feature called Dynamic Host Configuration Protocol (DHCP). You can read about DHCP here...

  http://en.Wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol

  Basically, when a device on your home network needs an IP address, he asks your router and your router assigns an IP address... technically, "rents" the router address for a given period (one day). Once this period has elapsed, the device must 'renew lease'.

  DHCP stops you from the hassle of having to assign a static IP address to each device on your network and then don't forget to retrieve that meet if/when a device are removed from your network.

  Sometimes the process DHCP can be confused and assign the same address on multiple devices. If/when this happens, communication between devices on your home network may be confused. Windows is smart enough to detect that another device on your home network has the same address as the computer where Windows is currently running..., but Windows can not solve the problem.

  You can determine the IP address of the computer that is running Windows (and posted the message you saw)... by entering "ipconfig" (without the quotation marks) at a command line prompt. Then you can check the IP addresses of all devices on your network until you find the other devices with the same IP address. Then you could say either every device to get a new IP address of the router (or restart the device). Alternatively, you can try just stating the computer that is running Windows to get a new IP address (by first entering "ipconfig/release" then "ipconfig / renew" in the command-line invite him... all orders without the quotes).

  But since you said that you are not very tech savvy, my first suggestion was the easiest... just shut everything in your network, and then restart one at a time by starting with your ISP device, router, and other devices. If the problem persists after that, then more troubleshooting (as described in the previous paragraph) would be necessary.

  I hope this helps to clarify the issue for you. If you have any questions, please post them and I'll try to answer.

• WAG325N, DHCP, and the DSL dynamic IP address

  Hello. I have problems with the implementation of my router, a Linksys WAG325N. My internet connection is DSL. According to my ISP, I have no username or password for my account because my connection uses a DYNAMIC IP ADDRESS. The operator of my ISP tells me that for my WIFI connection all I have to do is to set it to DHCP. That's all. My ISP does not help me because they sell another brand of routers with their DSL...

  My default IP address is 192.168.1.1

  I use to access the control panel of the CIsco modem. No matter what I do, the light of the internet on the router is always Red; the power, ethernet, DSL, and wireless lights are all yellow.

  What should I do?

  Thanks in advance and MERRY CHRISTMAS to all!

  Finally fixed it!

  Here's what I did:

  Encapsulation: RFC2684 Bridged (thank you GV!)

  Multiplexing: LLC

  Called my service provider for these values:

  VPI: 0

  VIDEO RECORDER: 100

  So that anyone who is going to be having the same problem I did find this:

  My ISP is PLDT MyDSL. My linksys model is WAG325N.

  Merry Christmas to all!

  Thank you once again, GV!

• WRT160N: Getting dynamic IP address 169

  Hello!

  Linksys WRT160N, bought yesterday and I want it behaves same way did my Buffalo WHR-HP-G54. So I live in apartment building for students, and we don't have modems, just the RJ-45 ports in the wall. If I plug the cable directly from the wall of the network card in my computer, my computer receives the dynamic ip address from the ISP. With my Buffalo, I connected the ethernet to the WAN sa-port cable and changed the router in bridge mode. In this way, there was 4 other ports free for the other PC and of course wireless too much for the other PC. Each PC connected via the Buffalo had a dynamic ip address from ISP, up to five addresses, which is the limit of my ISP. I plugged the ethernet cable from the wall of WRT160N Internet port and disabled NAT, dynamic routing (RIP) and DHCP server on the router Linksys, so all my computers have addresses ip starting with 169. And when I plug the ethernet cable from the wall to a port other than Internet-port of Linksys, all computers get the correct IP addresses via a wireless cable. What is wrong, is at - it a setting I have not seen? Some setting that I can use Internet-port and have other 4 free ports for other devices and other devices can get dynamic IP from my ISP.

  Ignore the Scrooge. What he wrote has nothing to do with your problem.

  Unlike the Buffalo WHR the Linksys doesn't have a configuration option or switch to alternate between the 'bridge' and the router mode. The Linksys always uses the internet port on a different interface of the numbered ports. You can't fill.

  For example, if you want to 'bridge' with the Linksys is the configuration you already have when wiring from the outlet ports numbered, i.e. do not use the internet port. You will have to "give up" the internet port then. If you need more wired ports, you must connect a switch to the router.

• How to change (dynamic) IP address in Windows 7 or Vista?

  Had the same problem on Vista, upgrade to Win7 and the question remains.

  I have a dynamic IP address from ISP, but it remains as if it was static, what allows to work in XP and previous versions of Windows no longer works in Vista or 7. I talked to my ISP (3 times, 3 different Tech), they said that my IP is dynamic and confirmed he is not defined by them as static. They charge more for a static IP, it would just give me this free 'upgrade'. They had "no idea" how to force/change a new IP address in Vista or 7.

  Please! Don't bother suggesting to run ipconfig/flushdns / release / renew at the prompt to as suggested by each internet search, this DOES NOT WORK. This was done with the prompt window of cmd under "Run As Administrator".

  Please! Read everything I've done here before suggesting something, I have tried or have tested and proven to work/not work.

  Here are other things that I've tried, WHO ALSO DO NOT WORK:

  (NOTE: no router is used, directly connected, CAT5, NIC the modem PC broadband)
  -Modem unplugged 72 hours left. No change
  -A the ISP send me a new modem. No change
  -Uninstalled NIC. No change
  -Change IP4 settings to "Obtain automatically" to a forced IP made-up, rebooted, then changed back to auto. No change

  So, with all this 'old school' stuff already tried and failed, that changed in Vista and 7 which seems to keep the same dynamic IP static? When Windows is put in cache or store this information, so I can delete it, none of the traditional methods of work. I absolutely can't stand having a static IP address on my computer at home.

  If you search on the internet this exact question you will find what I have, everyone is suggesting to the methods of work time I tried already above, but people using Vista or 7 are several times to find it no longer works.

  Here is some information, which confirms the IP address is not stored in my modem, or assigned to the MAC address of my NIC...

  If I start this same PC with a LINUX Live CD, type using the same MAC address and the NIC, he gets another IP address whenever it restarts. The question clearly has nothing to do with my ISP, modem or PC in general.

  If I get hot swap my modem to another PC, the other PC Gets a fresh (different) IP address. If this another PC using XP I can force the ipconfig/release / renew to change its IP address.

  If the other PC running Vista, the IP address remains static, no matter what I try, unless the hard drive is wiped and Vista is re-installed, then he gets a new IP on the PC with the pure install, but it can not be changed after what is happening.

  If clear, Windows Vista and Windows 7 have somewhere IP configuration information and re-use of this information when it detects that you are using the same internet provider, WHERE is it stored so I can delete it?

  I thank you much if you have a working solution and actually know the answer, instead of reading everything that can already be found by a search engine and repost info which is no longer valid, as all the world on the internet is doing in trying to answer this question.

  I think I found a solution. It has worked for me so I guess it could work for you.

  1. find your IP address for example to go to a site such as http://www.whatismyip.com/ it will show you your IP address.
  2 copy.
  3. open network & sharing Center
  4. open the network properties you what your IP to change. In my case, it's an EVDO modem.
  5. on the network tab, double-click TCP/IPv4, which will open a window to change the IP and DNS IP address.
  6. in this window click on "use following IP address" and paste this IP address you copied in step 2.
  7 change the last digit of the IP address to any value above him for example if its 192.168.23.123 change the last digit to something like 122 so that the IP address becomes 192.168.23.122.
  8. click on OK until that close all windows.
  9 disconnect from this network.
  10 reconnect to this network and if it goes as planned the ISP should force a dynamic IP address. Check http://www.whatismyip.com/ if it has changed. If you can not browse, go to step 6, and then select "Obtain an IP address automatically" and then disconnect-> reconnect to the network.
  It worked for me so I don't know if it will work for you. Your comments will be greatly appreciated.

• Dynamic IP address of the remote VPN L2L ASA sites

  Hello

  I have a client who is to change their links to backup from ADSL to 4 G - LTE using Cisco 819 s.

  Unfortunately, access to 4G of PSI will have dynamic IP addressing. Online, I see configurations for one remote site with dynamic IP address, speaking to ASA, but I can't find anything on several sites of L2L linking to the ASA with dynamic addressing.

  Does anyone can help with examples of configuration

  concerning

  Richard

  Hi Richard,

  the next days I will also write a blogpost with triple recovery WAN by using this configuration.

  Michael

• "Error: failed to get the IP address of the destination virtual machine running the converter to assistance server." with a static IP address

  Hi all

  I'm trying to p2v linux 6.4. It fails with the following message is displayed:

  Error: Cannot get the IP address of the virtual destination machine running the converter assistance server.

  I have seen discussions on this message, but they all refer to dynamic IP address, taken from DHCP, as in my case, I use static IP address.

  In the meantime the p2v (which then breaks down...) I open console support machine and saw a message:

  
  

  eth0 is not a recognized interface.

  Can someone tell me what is happening?

  Hello

  I assume you are using converter 5.5. There is a new feature that allows the selection of the network card. However, it works well in the case of Linux P2V. If you have changed the type of adapter, use 'e1000' or 'auto' and try again.

  HTH

  Plamen

• Problem installing oracle 11 g 2 in a virtual machine with IP dynamic

  Hello

  I have install oracle 11 g 2 on a virtual machine in Vmware workstation with dynamic IP address.

  Then I noticed that the global database name is orcl.16.27.57, and the identifier service oracle is orcl on step 10 of window 19

  There will be a configuration manager warning and the company failed due to the following error:

  Listening is not or the database service is not registered with it.

  And even I change the name of global database for orcl, it has also failed.

  When I use the static IP, the name of the database world so SID is orcl.

  then complete the installation.

  So I don't know what the reason is, how to install it without warning during the dynamic use of IP.

  Whenever I have install oracle with static IP, I can't continue like that again.

  Help!

  Thank you

  Now, I'm happy to say it works. Two methods to solve this problem.

  1. install Microsoft Loopback adapt

  2 edit the file hosts, IP hostname

  Of course, we can run them both.

  Thank you

• Server 2008 (R2): dcpromo fails due to dynamic IP addresses

  It is my first installation of Windows Server 2008. Maybe someone has an experience with this?

  I installed Windows Server 2008 R2 in a VMWare environment. For networking, I chose Host-only in VMWare Workstation and installed Windows Server 2008 R2 Standard.

  After that, I added the AD DS role for my installation of Windows Server 2008 R2 and run DCPROMO. EXE...

  The arrested installation process between the two because of the dynamic IP addresses. I went into the properties of the LAN adapter and changed from a static IPv6 address. (I disabled IPv4).

  After that restart dcpromo still refuses to go beyond the point where it looks for dynamic IP addresses. He seems not to recognize the static I chose.

  There may be something to do with my computer? I don't think he has a related issue R2 because Active Directory has not changed "r1".

  Any help is appreciated.

  Axel Dahmen

  .

  .

  That's what said IPConfig (it's in German, but I think that the values speak for themselves):

  C:\>ipconfig /all
  
  Windows-IP-Konfiguration
  
     Hostname  . . . . . . . . . . . . : VM-Win2008-R2
     Primäres DNS-Suffix . . . . . . . :
     Knotentyp . . . . . . . . . . . . : Hybrid
     IP-Routing aktiviert  . . . . . . : Nein
     WINS-Proxy aktiviert  . . . . . . : Nein
     DNS-Suffixsuchliste . . . . . . . : localdomain
  
  Ethernet-Adapter LAN-Verbindung:
  
     Verbindungsspezifisches DNS-Suffix: localdomain
     Beschreibung. . . . . . . . . . . : Intel(R) PRO/1000 MT-Netzwerkverbindung
     Physikalische Adresse . . . . . . : 00-0C-62-60-29-05
     DHCP aktiviert. . . . . . . . . . : Nein
     Autokonfiguration aktiviert . . . : Ja
     IPv6-Adresse. . . . . . . . . . . : fc00::c:62:60:29:5(Bevorzugt)
     Verbindungslokale IPv6-Adresse  . : fe80::f054:5062:c2fd:bd8f%11(Bevorzugt)
     Standardgateway . . . . . . . . . :
     DHCPv6-IAID . . . . . . . . . . . : 23488418437
     DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-12-39-29-42-69-0C-00-9E-83-6A
  
     DNS-Server  . . . . . . . . . . . : ::1
     NetBIOS über TCP/IP . . . . . . . : Deaktiviert
  
  Tunneladapter LAN-Verbindung*:
  
     Medienstatus. . . . . . . . . . . : Medium getrennt
     Verbindungsspezifisches DNS-Suffix:
     Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
     Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0
     DHCP aktiviert. . . . . . . . . . : Nein
     Autokonfiguration aktiviert . . . : Ja
  

  use static ip on ip 4.

• What does this mean and how to fix: the router address you entered is not compatible with your WAN IP address.

  I connect to an access provider via Airport Extreme, which is extended through two Airport Express.  When I try to edit anything in one of these devices, even a name, I get this message: "you have entered the address of the router is not compatible with your WAN IP address.  My connection seems to work, but there is clearly something wrong with her.  The Express has no DNS and will not update without the same message.  I have no idea what this is all about and will greatly appreciate the ideas.

  This means that WAN Setup does not or does not install across the network.

  The best way to solve this problem is beginning on...

  Reset all three at the factory and reconfigure each in turn. Do the extreme first and make sure it works... Then add the express.

  If you need help with that we will need to know which modem or modem router to your ISP gave you and possibly the type of services to wide band... and who is the provider.

  Give us screenshots of each installer as you do.

• How to play music purhased with the old email address

  I have a few songs purchased on iTunes with an old email address. When I try to play, I am told I must allow the computer under the old address, but the computer is already allowed. Suggestions?

  If the computer is allowed with this specific Apple ID, permits it. authorizing an Apple ID does with the other.

  If this is the case, remove and redownload the songs if it's free in your country.

  (139523)

• Message appear conflict of IP address at startup. Another computer already uses the network with the same IP address. How do I cure this?

  When my kids play online on the X - Box I get an error message on my laptop when I start after them. It is said there is an IP address conflict and that another device is already on the network with the same IP address. It does not affect me access internet even if. How can I fix thi.

  Hello

  1. which is the version of Windows installed on the computer? For example, Windows 7, Vista

  2. only the error message appears only when the Xbox is connected to the computer or at both times?

  3. have you made any software or changes to the material on the computer before this problem?

  Please answer these questions and provide additional information so that we can better guide you.