WRT54GH - connect to the modem / router

Similar Questions

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Loss of internet connectivity after the modem / router reset

  I have a BEFSX41V2 and a Motorola SB6141 DOCSIS 3.0 modem.  My provider is comcast.  After all devices reset, unplug the power and remove the cable / ethernet cable, I lose all access to the outside.

  The strange thing is that if I connect any desktop or laptop computer at home directly to the modem, I have access.  In this case, the link for the transmission light / receipt of data on the modem is on.

  I had to send signals of reset comcast several times but it does not solve the problem when the modem and the router BEFSX41V2 are connected.  In this case, the link for the transmission light / receipt of data on the modem is turned off.

  Are there additional steps I must take on the router to reactivate the connectivity.

  Thank you.

  George

  Have you tried to do a hard reset to the router and then reinstall parameters later? To do the reset, please press the reset button at the back of the router for 30 seconds while the unit is turned on. After unplugging and then start from scratch. You can check this link, http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=fccaaff524a24bc9a08172ea696f8ed1_4737.xml&pid=80&r...

• C7280 all-in-One connected wireless to modem-router needs a password when it is fed - up.

  Do you have examples of wireless connection to a HP Photosmart C7280-all-in-one to a network managed by a modem-router method NB6Plus4W? The modem-router attach also your desktop of Windows XP by using an ethernet cable and a laptop computer to Windows XP wireless using the default (wireless) SSID and password (a1b2c3d4e5).

  The wireless connection between the modem and router and the laptop happens automatically when the modem-router and laptop computer are powered.

  The wireless connection between the modem-router and the HP Photosmart camera does not automatically. When I put power on the HP Photosmart camera, I then use the setup on the Photosmart button and type manually in to the Photosmart (a1b2c3d4e5) password. The SSID also displays wireless, it doesn't have to be retyped.

  Do you know if there is no method or HP configuration that will result in the automatic installation of the camera HP Photosmart to occur when it is powered?

  What I am complaining about is having to manually type in the HP to HP password whenever the HP is powered.

  Go to Setup > network > advanced settings > IP settings and now select Auto and press OK. See if this stops the question.

  If that doesn't work, then go to settings > network > restore default settings of the network, and then run the Wireless Setup Wizard to connect to the network.

• Router is not connecting to the modem so I can't get internet

  All right-_ - I tried a lot of things with this so I get irritated sorry. Here is my info I have a Linksys Wireless Router with SpeedBoost Firmware Version 7.2 WRT54GS (latest version). I'm trying to use it with a Sprint 645 series Modem. My IP address when you are connected to the router and the router connected to the Modem is 192.168.1.100 who my ISP said was ok to make it work. While it is just connected to my modem, it's the same thing except replace the 100 by 1. My ISP uses a measure of security where The Thing DHCP is 192.168.1.1 and so is the DNS server and default gateway and im not sure if this has something to do with it. I used the ping at a command prompt to make sure that I am connected to the router when its plugged up and it is. This is a new router. I have internet with Modem just perfectly. I tried to reset the router and that does not work-_-. I don't think it is important more because I tried to fix the many way people have told me and it didn't work, but I'll tell u in any case. When I put up the first router time I hung and lit everything at the beginning. Then I noticed that it says Run CD before to connect the cables... those who were not in the instructions but wtv... anyway resetting should have fixed or so I was told by other people on this forum. I use a laptop with Windows Vista, and I don't have access to a desktop computer in case I need a XD. I can connect to the router fine because I can access the Setup page... and I can connect wireless... The ONLY problem seems to be that the router will not connect to the Modem... for some reason of wtv-_ - I think that its because the entire security measure on the way to the DHCP and the DSN and the bridge are all 192.168.1.1, but that's just me. I'm sorry this is very long but I really want this problem-_ - I had this router for a month and becomes really annoying so please help . My ISP is Embarq. I ran the installation CD and I had all through the last step (standby router) after having connected the power supply to the wall for the router. Just, it is there forever and then says "error: 322 cannot find router or something like that." There are 3 steps to try to fix it. It says to make sure that the router is connected (it is), it is said also to make sure that u does not actually connect your old router, (I don't have a-_-) and then re-run Setup. and by the installer, I mean where u plug in all the cables in the right way. * sigh *.

  If you need anything else please ask.

  Your second post says "" ignore this "so I guess everyone thought that you set..."

  When you connect through your router that you have two instances of DHCP past... one is your DSL modem with router IP address on its WAN interface. The other is the router that gives your computer an IP address via the DHCP server on the router. The IP address of the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the reange of Linksys routers LAN IP address is also in this range. For that to work, you must set your router 192.168.2.1 LAN ip, so that the LAN and WAN router interfaces are in different networks.

  To do this, unplug the DSL modem router, power it and your computer, and then connect the computer to the router by an ethernet cable. Turn on the router and the computer, and then go to 192.168.1.1. Change the LAN IP on router 192.168.2.1, save the configuration, and then restart the computer. Once the computer returns to the top, navigate to 192.168.2.1... you should be able to get to the router GUI configuration.

  Turn off the router and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, and then turn on the modem, then the router... you should be good to go...

• I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

  Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

  The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

  Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

• Problem with TC loss of connection to the modem cable

  I have a TC of 2 TB which is connected to my ISP provided by cable modem. It worked fine for 3 months after the installation in December, but now all of a sudden it will lose its connection to the modem and we lose our wireless internet. We have replaced the modem cable and it does not solve the problem. I have to reset the TC 2 - 3 times a day. Nothing else has changed recently with regard to the network set up. that only changes were to specific devices that use the wifi connection, and this was always something changing, depending on the devices we use. Any thoughts? I'm not a savvy person tech, BTW.

  We need to ask a few questions in order to learn more on what the possible cause of the problem might be.  Please be patient with this. Thank you.

  What is the number and the model of the modem you are using right now?  We ask because some modems work better than others with Apple routers, and even if you have changed the modem, it could still be a model who does not get along well with the Apple router... or... you could say that the router from Apple does not get along well with the modem.

  How old is the TC? We ask because the life expectancy, on average, a time capsule is about 3 years.  After that, they tend to start losing connections to an ever-increasing rate.

  Who is your provider of Internet (ISP) Service?  We ask because most suppliers are in the active process of implementation of a new type of connection called IPv6 in their systems... and despite ISPS claiming that their system changes should cause no difficulties connection or interruptions system... which doesn't seem to be the case at all.

  We have seen an unusual number of reports from users who suddenly have problems with their ISP connection, when things were very well for many months before. That points directly to the IPv6 changes that ISPS are doing as the culprit. In some cases, there could be way to work around the problem, and in some cases, there is nothing to do but wait as the ISP to complete their changes and be everything to speed.

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• Boxes wireless printer work without connection to the modem HP 6700 printer

  My printer is located on the second floor of our House. It is connected to our network with the modem and the router to the first floor where my wife's computer. This connection works fine.

  My problem is that my printer only works if connected to my computer with a USB cable. This limits the use of a number of functions of the printer. Print the test pages that I myself say the printer is connected to the home network, but the printer will not work without the USB cable that turns off the Wireless function.

  Most of the instructions I've read show that I need to be connected to the modem downstairs to work. It is not possible that I can tell.

  Is there a way to fix this? or is a wireless connection to my printer not possible with this configuration?

  Thanks for your help

  Bill6700

  Bill,

  Welcome to the HP Forum.

  You don't mention what kind of computer of mystery that you have and try to use the printer.

  Assuming that the full feature software is available for the operating system of your computer, this may solve the problem - multiple computers can print once installed wireless printing software.  I hope that your computer is among the supported systems.

  General instructions to install the printer software

  Reminder:

  1. In most cases, the Solution Center has been replaced by the wizard of the printer.
  2. Shortcuts to the Printer Wizard must be installed on your desktop during the last part of the installation.

  Windows operating system:

  • Create a Restore Point: create a restore - Win7 Point OR create a restore point Win8
  • Open drivers HP & downloads
  • Enter your printer model information
  • Select your printer in the list of the 'results '.

  OR

  • Open printer HP Officejet 6700 Premium e-All-in-One - H711n drivers
  • Enter your operating system the menu drop-down
  • Click NEXT and scroll down
  • Find the driver - product Installation software category
  • Select the driver of base, e-print, or full software functionality
  • Save the package *.exe Setup on your computer

  The files will probably save in the "folder"downloads. "

  Don't forget to search for updates as necessary for your installation. If available, you can download print and scan doctor and / or other programs of category - utilities.

  • If you have control of "Admin", you can highlight the package and "double-click" to install it, otherwise just right-click, select run as administrator and install.

  NOTES:

  • Look at the bottom half of the main Web page for your printer for helpful videos help with the installation of the printer software!
  • Scroll through the list of videos back until you find the video that best fits your situation.
  • If you use a USB connection: download and install the driver software before connecting a USB cable.
  • Ethernet: connect the printer to the network and (optional) assign the printer IP address to the router. Once the printer is connected to the network, make sure that the printer is on, and then install the printer software.
  • Once the initial installation is complete and functional, check / install category - updated

  There is valuable information about the Web site, including your Manual, sections for Troubleshooting > How-to's, Troubleshooting > solving a problemand alerts and notifications for your printer.  Be sure to take a comprehensive look at what's available.  To bookmark the page.

  Click on the Thumbs - Up Kudos to show that you appreciate the help and time of our Experts.

  Click on accept as Solution when the answer is a good solution or workaround!

  Although I strive to reflect best practices of HP, I do not work for HP.

• PROBLEM CONNECTING TO A MODEM/ROUTER TO COMCAST

  My husband is trying to connect to my laptop to WORK FOR our COMCAST Modem/Router (IPV4) House.  There is a link between the laptop and the modem/router.  However, I can't get out to the internet WIRLESSLY and need to use a WIRED CONNECTION.  He did an audit of the IPCONFIG command AND maybe he thinks running IPV6 as we do at work.  It's what the IPCONFIG/all command shows:

  IPv4 address: 172.X.X.20 (preferred)

  Subnet mask: 255.255.0.0

  DHCP SERVER: 172.x.x.1

  IAID DHCP: 2255216532

  DHCPv6 Client DVID: 15-digit number

  Is that mean that the computer is configured to run on IPV6 instead of IPV4?  My husand does not have IPV6 on our home network?

  He doesn't have SYSADMIN access, is there a way to fix this without sysadmin access?

  Leticia

  Hello Leticia,

  Welcome to the Microsoft community.

  What is the brand and model of your computer?

  Launch us network troubleshooting utility in Windows 7 that allows anyone to diagnose and fix network problems.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Make sure that all network drivers are up-to-date. You can follow the steps in the article below.

  Automatically get recommended drivers and updates for your hardware

  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

  More information

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful. Feel free to get back to us if you need further assistance.

• No internet access when it is connected to the modem

  HI I have an Ethernet cable modem BEFMCU10 model v3 connected to a Netgear n100 v2 wireless router. The modem works only when it is connected with the wireless router. When I try to connect Ethernet. Modem to PC, it does not connect, there is no internet access. My ISP is Comcast (Xfinity). It's really weird because how is it possible that theres internet via wireless, but when I connect my modem via Ethernet, I have no internet access

  I remember the first time I activated my modem there is xfinity software that did something to my modem but I don't think it has to do with anything he just install something in my laptop. I did a clean install of the software or anything has been removed.

  > Sometimes I download things and I prefer to use the physical connection because its faster.

  You will get the same benefits and an easier time using a wired connection to your router, rather than the modem.

  > My prolem is resolved, I followed your instructions, thank you

  You are welcome. Please mark as replied to close the issue.

  > is - this quite useful to purchase a Docsis 3.0 modem

  You can check this with your cable provider, but probably not.  Unless you have a very high speed (usually of company type) cable plan there would be no advantage.   You also must be sure that any modem you purchase is compatible.

• Satellite A110-195 unable to connect to the WLan router

  Hello

  I have a wifi router and I have connected my laptop and it worked wery well but on low there is I could not conect to router but woudn't ip address pop up. Internet access was not.
  I am connected to the same router another device and it worked...

  Hello

  Believe me, there is no general solution, you must check all the settings of your operating system

  First of all that I recommend to check the parameters of the TCP/IP protocol if everything is settled automatically on.
  Then check if you are using encryption parameters right as standard (WEP, WPA, WPA2) encryption and the encryption key.

  It s also advised to reinstall or update the Wlan card driver

  If you used the windows own WLan configuration, I would recommend testing as Atheros Client utility or Intel ProSet Wlan client configuration utility. But it depends on the WLan card what client WLan configuration utility can be used

  concerning

• Satellite L40 - 14N does not connect to the WLan router

  Bought two portable Satellite L40 - 14N as Christmas gifts and one of them does not connect to the wireless router.
  Is the error that says "error message unknown" try please login again.

  The wireless network appears in the list of networks available with a strong signal. Notepad attempts to connect but the error 'wireless link failed for an unknown reason. " Made a comparison with the other laptop that works very well and the configurations appear to be identical!

  Tried it on wireless network from a friend with the same result. All suggestions, am pulling out my hair at this point.

  Seems to be a Vista issue.

  I found this article Ms knowledge base:
  http://support.Microsoft.com/kb/928233/en-us

  You need to add a value in the Windows registry.

  1. Click Start, type regedit in the search box, and then click regedit
  list programs.

  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE es\Tcpip\Parameters\Interfaces\ {GUID}
  This registry path, click the (GUID) subkey that corresponds to the
  Network adapter that is connected to the network.

  3. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  4 new value #1, enter DhcpConnEnableBcastFlagToggle, then
  Press ENTER.

  5. right click on DhcpConnEnableBcastFlagToggle, then click on modify.

  6. in the value data box, type 1 and then click OK.

  7. close the registry editor.

  concerning

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• I received a message on my laptop computer that says not able to connect to the wireless router.

  I received a message on my laptop that says could not connect to the wireless router and it make reference to section of the knowledge base Microsoft 87112 for more information.

  I think you have transcribed the number incorrectly.  I think that the article you want is this one: http://support.microsoft.com/kb/871122