Yellow LED blinks always executables!

Similar Questions

• Portege Z930 - 14L - DC orange led blinks 8 times and green ECO light led

  Portege Z930 - 14L. I can't boot from the last power since.
  The domain controller in the orange Led blinks 8 times and eco green light led is lit.

  DC IN flashing ornage indicator indicates a problem with the power supply. Initially, you should try plug the adapter HAVE an another power outlet. If she does still not work, you should contact Toshiba ASP (authorized service provider)

  Electronic supply on the motherboard is probably the problem.

• Satellite A100-847 battery led blinks 11 times, absence of motherboard?

  Hello

  14 months (only 12 months warranty), I have a Satellite A100-847 was a laptop perfect, but 2 weeks ago the ac-adaptar falls down and since then that if I push the power button the battery orange led blinks 11 times with the same length, but nothing happens.

  ASP did not now what this flashing means but think I have a motherboard problem.
  Now I found on ebay a Satellite A100-153 and my question is, is this the same motherboard, because it's also 945 PM.
  (Sorry for my bad English)

  [Satellite A100-847: http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/SUPPORTSECTION/discontinuedProductPage.do?PRODUCT_ID=120570&DISC _ MODEL = 1 & service = EU]

  [Satellite A100-153 | http://de.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/productPage.do?service=DE&PRODUCT_ID=112714&PRODUC T_ID = 112714 & toshibaShop = false]

  THX.

  It seems that two laptop computers support the same motherboard as the Satellite A100-847 and Satellite A100-153 belong to the same series of PSAA9E.
  This series uses the same drivers and the same BIOS so I think that the mobo must also be the same.

  PS; I think that it is a motherboard problem too. Such a code is displayed only if a hardware failure has been detected on the motherboard.

  Best regards

• Satellite Pro A120-151 - switch and power LED blinks

  My 120-151 will stop when I used it. On the laptop, the power LED flashes: short-long-long-short-short-short-long-short

  Anyone know what this error code?

  Hi mate,

  I had a similar problem which stops my Satellite A300 and the power light was blinking. This happens always after 1 or 2 minutes.

  I decided to contact an authorized service provider. Technicians control the laptop and fix it for me. The repair took only a few days and it was free because the laptop was still under warranty.

  I hope I could help a bit! :)

• Satellite A500 - 14 k - HARD Drive LED indicator always flashes

  Hello

  First sorry for my bad English

  I'm french and I recently bought a Toshiba Satellite A500 - 14 k (http://fr.computers.toshiba-europe.com/innovation/product/Satellite-A500-14K/1072806)

  I have a little problem with this laptop and I don't know if anyone has a solution

  The HARD drive light flashes constantly (1 blinking per second) even in safe mode. I checked some forums and I learned he had something to do with the function of autorun cd /dvd CD/DVD recorder.

  If the autorun feature is disabled in the windows registry (HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servi ces\CDRom and the key value goes from 1 to 0) the flashing disappears, but I can't access my data from CD or DVD (media are marked as empty). However, the audio CD and video DVD work except that they cannot be started automatically.

  The same thing happens if the CD/DVD writer is disabled in the control panel Device Manager: the led indicator has a normal activity.

  I would like if this problem occurs with other owners of this product and if there is a solution to use normally without this flash recorder

  Thank you

  I don't have A500 but A300 and I can't say with certainty why this and what kind of HARD drive activity is ongoing, but what you can try is to remove some pre-installed Toshiba stuff like TEMPRO or pre-installed application antivir.

  When the laptop is new days that many updates will be installed and in the background is always a certain activity. Automatic update is disabled?
  Try also to remove TEMPRO. This tool is active permanent and search for updates.
  Try to optimize the operating system preinstalled and carefully monitor if something will change. I always do after clean operating system installation.

• Satellite Pro L650 turns off after start; DC In and Power LEDs blink on stop

  A friend Satellite Pro L650 having worked well until yesterday, all of a sudden turned itself off. Now, at startup, it lights up normally for about 10-15 seconds before turning off suddenly. Turned off, the DC in white/blue LED and the orange Power LED Flash on a broad set of intervals of approximately one second. This extinction happens if I leave Windows or press F2 to enter the BIOS setup.

  I guess this blinking is intended to serve as a kind of diagnostic code, but I have yet to track down what it means. Can anyone help?

  To avoid confusion, power without the product stack the same, sudden stop experience, except the two LEDs remain solidly lit this time. With or without battery, trying to turn on again immediately after that a shutdown produced no response at all. Remove the power cable and immediately it reconnect again and turn then produced a brutal power off, but in less than 5 seconds. More wait between attempts to market seems to give a little longer powered on State, but without fault, the machine turns off just suddenly. With its short time 'turned on' we are talking, there cannot be any kind of thermal protection?

  I had an old Satellite L450D lying around that uses coincidentally the same AC PA-1750 adapter, but use it made no difference. Of course, the battery does not have the L650!

  The only previous numbers, that I am aware of this machine have been intermittent case of Windows reporting "Plugged in, not charging", but as my friend use it exclusively on the network, it was not a problem.

  Your thoughts will be greatly appreciated...

  WTF?

  What is an unmoderated forum?

  Can someone help with my problem?

• Satellite A10 dies after the power LED blink

  Hello

  I have a problem with the power supply of my Toshiba Satellite A10. Sometimes, after the computer sat for some time, I have a problem with the power. The "plugged power cable" - LED will start to blink and shortly after, the computer just dies.

  It can also have the time to go into a lower energy state before he does. When it happened once, it will most likely happen also when I restart the computer, but after a much shorter time. WXP won't even have time to start. If I stop to select the source of start-up, the problem will occur anyway, this isn't the software. It should also be noticed that when the computer is not turned off, the 'smart power' - is on correctly.

  I know that my battery is not very good. Completely loaded, the computer can run for maybe 3 minutes with only the battery. I know that I must have a battery connected, even if I use the power cable, but this occurs even when the mine problem. The battery would be pretty bad not even allow me to use the computer with a cable?

  It should be added, that sometimes I can use the computer for long periods of time without this problem to happen. I also have a problem with the battery not being not properly in physical contact with the pins of the computer, but this isn't the problem here, because I have the same problem with the battery removed and me holding the battery in place.

  Thank you for your help.

  Andreas

  Hello

  You description is very long and detailed and it of still not easy to say what's wrong.
  Usually, the DC-In witness lights up green when DC is provided FRO the AC current. If the output voltage of the adapter is abnormal or if power outages, this indicator flashes orange.

  So I think that is your AC adapter malfunctions or there is something wrong with the electronic power supply on the motherboard.

• Toshiba Satellite CDT4070 power on problem - orange led blinks 8 times...

  I have a problem with my laptop, it's a Toshiba Satellite CDT4070. When I press the button start power
  Tour LED from yellow to orange. Then the LED flashes 8 times. SLSSLLLS = 01001110. Peut
  can you tell me what this error code means?

  Another person wrote "I solved the problem" by connecting the 2 PCBS together. but what is PCB? I do not know.
  I will be grateful for your help.

  Post edited by: krystianic

  Hello

  I guess that the "0100101010" - code must be some kind of error code, but I'm not sure. But even if that's who you wouldn get information on this subject given that these technical information are kept for toshiba technicians, I guess. :)

  So, in this case, you can not do anything and just ask some laptop technician/service station for a checkup of material or a repair.

  Sorry mate, but that's all.

  Good bye

• Satellite P300-16 t - power power LED blinking

  I replaced my old charger yesterday and when I plugged the new charger yesterday everything was fine, but when I plugged this morning the power led continues to blink continuously. I took the battery and everything all right, the power led remains lit.

  What I need to get a new battery or is there something else that needs to be replaced?

  A new charger the same previous specification?

• Satellite A105-S2031 battery LED blinks 11 times.

  Everyone has been able to diagnose this problem until the fault? A few days ago, this very laptop just turned power off and since then the battery led just blinks 11 times and nothing more. I disassembled the laptop and everything looks fine on the card (not the type to be skittish around electronics. Worked on cell phones for the last five years). Anyone have any ideas?

  Have you tried to boot up your laptop with AC only (removed battery) power?
  I really can't believe that you can find the reason why this happen if you take apart your laptop. I assume that there must be a problem with electronic control gear.

• user led blink

  I trained with the events of the user to leave the course textbook, an example of Core 3. I did not use the blinking.vi like NOR use, instead I assigned a value Boolean true to the flashing for the event property node shot LED I want to blink only once during the event of user after the Fire Event button is pushed. But for some reason, the led does not blink. I tried to apply a value Boolean true and writes the value of the control of the Boolean Fire Event on the front panel when it touches Fire Event is pushed, but neither seems to be impacting on the fired event LED. Can anyone tell my why it doesn't work?

  The vi has been done in version 11.

  Thr problem, it is that you do not understqnd what the property of blink. It causes the Boolean value to Flash at a frequency of 1 Hz. Your property code turns on but then turns off it back 25 ms later. There is never a chance to blink.

  Mike...

• HP G32 white screen with all LEDS blink and CPU fan run fast

  Hi all

  I have a laptop HP G32-205TX

  I had a problem that was the device would be loop at startup without showing the start of message or HP logo.

  I changed the Ram memmory and it was fixed.

  Now I'm having a different problem some kind.
  Specifications stopped loop at startup but has all its flashing LED (Caps Lock, Wifi, Lan and the side LED)

  Please, someone help me.

  Thank you

  Hello @Khushal17,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that your laptop fan is running faster than normal and that all lights are flashing. I'd love to help you in this case!

  As a fan of hyperactivity is symptomatic of internal overheating, I recommend that you follow the steps described in this document on the reduction of heat inside the PC to avoid overheating. I also suggest to take a look at this resource: computer does not start and the lights blink or computer beeps, to determine the reason behind the blinking light caps lock.

  If the CAPS LOCK flashing indicates a hardware problem, or the fan continues to run at high speed, please call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps!

  Concerning

• Yellow LED light on router wrt320n for main wired computer. On 3 other machines,

  a Wi - Fi wireless and 2, the LED on the front of the router remains blue.  The yellow light for this computer tells me "ATTENTION".  Am I wrong?  I use the built-in 10-100-1000 nic and when I put my cursor on the monitor of the clock icon it shows 1.0 Gbps.  Computer works fine, but the yellow light concerns me.  Thanks for any help.

  If you found the yellow light, you will be connected with 1 Gbps and if you found the blue light, it will connect with 10/100
  speeds. Therefore, do not follow the manual... can be mistakenly LED on the router is in yellow.

• Reboot hangs with hard drive led blinking.

  My E6430 Latitude has been win10pro win7pro upgrade - no WOOD setting have been changed. It has 8 GB of ram, inspected, reinstall and test. It crashes with a disc hard blinking led that requires the power to complete on a restart button. No problem starting from button walk / stop or stop.

  I tried to install the proposed updates for the network and the Chipset on the support site, locally and in safe mode - say that they install, but not for the most recent.  The current A16 BIOS does not update the current A17 or A18. Even by pressing the power button on reboot clears the bios and the driver up to date?

  Thank you for your time to consider this, my first post.

  Further investigation found loose on the heatsink - screw tightened then disconnected wifi module intel and reinstall the connector screen just next door. With drive HARD and CD/DVD and removed WIFI, I started in Linux Kali on USB stick and hang and restart to work.  Put everything back together and restart the work! Update BIOS to A18.  Thanks for nothing... Not an exact answer to the cause. Hope this helps someone else.

• White screen on Boot and CAPS lock and NUM lock LED blinking on HP Pavilion dv - 6 portable 1210sa

  Hello

  I'm on HP Pavilion dv6 - 1210sa laptop with Windows vista Home Premium (service Pack2). It's the operating system, which is that the laptop came with when I bought in 2010 and later service pack 2 was installed using windows update. I can confirm that my laptop is up-to-date with updates of windows and hp installed periodically. My problem is the following:

  Everytime I turn on my laptop, I can hear the noise from the cooling fan and the led power and feather touch volume buttons and a wi - fi light up. However, the screen remains blank and the CAPS lock and NUM lock Dungeon LED flashing with three second gap between two flashes. They Flash together and blink only once in a single cycle. It keeps flashing even after leaving it for 10 minutes. I have to perform the hard reset several times before I can get it started. This problem started a few months ago with the frequency of the problem more and more. It has now reached a point where I encounter this problem on every start and even after the awakening of the laptop computer from standby or hibernation.

  I know that the flashing of the LEDs is typical diagnoses, but I was unable to understand the real problem. I know the screen works because I tested using an external monitor to work. It should not be the battery (even if it's crap to maintain charge) I tried to restart the laptop with just AC adapter connected (and battery removed) after having done a hard reset and still, the situation did not improve.

  Could someone please tell me what is the problem and what are my options? Think you that formatting my c: / and re - install the OS will solve the problem?

  Thank you.

  Please come back to me

  As long as you keep your files backed up on the outside, it is to you how you want to proceed. First question, however, is you are in warranty or not? If you are in warranty, Yes, call telephone support and will take care to have it sent repair.

  If you are no longer in warranty, however, that the repair can be expensive. You could certainly call for an exact quote, but according to the availability of the room, it might be around $200 and for an out of warranty repair. Money would probably be much more effective if they are presented to a new computer.

  HP Total Care 1-800-474-6836

  BUT, if you're still able to get the it to power (after trying it several times) and you're OK with the disadvantage, it would be nice to hold off on buying a new computer until it failed completely. I hate this word like that but I want to be realistic with you. I'm sorry that you are having this problem. As I said though, your files are the priority. Keep all your documents and photos and other precious files saved on an external hard drive or flash drive. Let me know if you have any other questions