black screen and slider with start now on windows 10

Similar Questions

• Windows load with black screen and does not start after windows updates

  Original title: load windows normally screen will not continue

  I went to my computer tower and I chose to install updates when closing.  I went back later to re - turn on my computer and now it loads to the top of the black screen that gives you 5 options. safe mode, safe mode with networking safe mode command prompt, windows loads normally and finally to load windows from last known configuration that works.  Problem is that none of these options work.  they all return me to the same screen.  Help this laptop came preloaded with Win XP Media Center edition and I can't get back to work.  IM assuming I need a XP disk support center but I can't find them anywhere! HELP PLEASE SOMEONE!

  Hi Burton089,

  Your hypothesis is right. To resolve this problem, we need to repair your installation of Windows using the Windows XP disk. We recommend that you contact the manufacturer of the laptop to check if they have the Windows recovery disk.
  See perform a repair Installation
  

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Qosmio G40 - black screen and does not start

  A bit of water on my laptop... (bought in 2007, guaranteed on)
  I did not cut power at the time because it did not work properly...

  But, the next morning.
  Start with a black screen, fan is too much work and I have a beep.
  An and after a continuous short beep...

  I opened it and dry all (air cold & mild)... paper to remove moisture.

  but screen remains black, a beep and the fan not working too.

  Please help... What can I do?

  Hey,.

  It seems that water damged your laptop or at least some parts. In the worst cases, you need a lot of new pieces of equipment, but I don't think that an authorized service provider can help you diagnose this problem.

  On the Toshiba site, you can search for them:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Contact them and ask for help. They will help you as much as possible. :)

• Lenovo X 201 laptop computer black screen and LCD does not detect after windows startup

  Suddenly, my Lenovo Thinkpad x 201 shows only a black screen. I checked the LCD screen with a light and I could see a dark image of the Thinkpad logo and then it go completely black. But when he is on safe mode, I saw my desk in black screen (when I use a light).

  I've updated the BIOS also using an external monitor. But still the same. I'm completely at a loss. Please someone help me to slove this problem...

  It is due to the inverter of the screen which has stopped working, it controls the backlight of the LCD/LED screen part when it breaks it causes the backlight to turn off and wont go on then you would need to have ups re-place with a new one.

  Here's an example of how it looks like:

  

  It may seem different on each model, but that's just one example of a lenovo T41.

• Reference Dell 5558, 8 beebing on startup, no black screen and works with the beebing

  Hello

  I have a problem with my Dell insipiron r15 5558, I bought it 3 months ago. But last month my laptop beep 8 times at startup. When this happens, I usually only the power out of my laptop because of the distracting noise and turn it back on. Once I powered on / off power for 3 - 4 times it don't beep plus one works very well. Anyone know what could be the problem? I ran a Test LCD and an analysis of Pre-boot system, it was running fine without any problem, I used my warranty and sent the labtop to dell here the last 2 weeks, they sent and didn't tell that it is no problem with my laptop, but it is still beebing 8 times by clicking on the power on

  BTW. I'm on Windows 10 pro 64-bit

  Hello

  8 attention beep is usually to do with the problems of LCD, as you already know.   If diagnostics are passing and the system has been returned to the warehouse for the evaluation, the only thing I think it could be is a connecting cable of the LCD screen.  You said sometimes works very well after starting several times, then maybe it's the cable.

  Have you tried to hold the screen in different positions when it turn on?   Just to see if guidance works better and maybe the cable is a better connection.  You can check if the cable is loose yourself.  Here is a link to the online manual for the Inspiron 15r 5558.  You can use it to see how a screen is normally replaced, but instead to replace it you would just check the connection of the cable to make sure it's tight.  NOTE: Make sure you follow the safety instructions and information in the section "before you begin".

  Let us know if you find a loose fitting and if the adjustment of the angle of the screen change anything when you try to turn on the system.  I hope it's something as simple as a bad connection and you can correct it.  If the ringing continues I recommend to contact Dell support again and have them send it back for repair, unfortunately.

  Todd

• Satellite A135 black screen and does not start

  I have a Satellite A135 with windows vista and I have not used in more than a year.
  I went to use it today and it turns on but the screen is blank. I can't even see not the bios.

  I tried the usual things, connect to a monitor, removed the chip of ram from the back and tried another one, I also tried power alternative only with no luck.

  All the ideas it might be.

  Thanks for the help

  Hello

  If the BIOS page does not appear, then it s a serious question.
  Seems that the motherboard is dead.

  In my opinion, a technician should check this section first, and perhaps you will need a new

  Motherboards are parties, then perhaps it s not an option for you

• Computer has a black screen and does not start. Vista of Aspire5535 Acer base

  As above.  Help please!

  Hello

  If when you start your Acer is no 'Acer' logo splash screen at all and nothing appears on the screen, which would indicate a hardware problem.

  If under warranty, contact Acer.

  If it is not under warranty, use a repair shop, local.

  See you soon.

• Compac cq62: downloaded windows 10. Now I have a black screen and the caps button continues to blink. All the answers.

  Downloaded Windows 10. 1 week later, I have a black screen. When I turn on the power to all I get is a flashing caps button one am not able to connect. Ilha a Compaq cq62 model.

  I have seen this reported, and the response is not good, sorry:

  "Problems of upgrading Windows 10: black screen after update (new).
  Some users taking advantage of the Windows 10 upgrade are the conclusion that once the completed upgrade their device just gives them a black screen and does not start.
  Microsoft is still working on a fix for this, but it's not a way to avoid it now. Worse, it seems that the problem that happens on multiple PC configurations. For now, we can only suggest using the utilities provided with your backup device and create some external media backup before starting the upgrade in case that happens. If this happens and you live near a Microsoft Store, make an appointment with them to have your device looking if you experience the problem. Some reports (such as those of our comments) indicate that disabling anti-virus programs before performing the upgrade prevents this issue. »

  http://www.GottaBeMobile.com/2015/07/30/7-Windows-10-upgrade-problems-how-to-fix-them/

• App stack (Toad for Oracle) cause VM to black screen and disconnect?

  When we attribute our Toad for Oracle (12.6.0.53) stack, the user will receive see the connected virtual computer, but before I get into the office will get a black screen and disconnect.

  Now, if not assigned, the user can open very well.  When we assign the battery, apply immediately, the app looks and works completely fine.  So the app itself isn't a problem, but something that happens when you try to attach to what is.  How do I investigate what happens?

  Then I temporarily mounted a 2.5.0 environment and recreated the Toad for Oracle stack with the 2.5.0 release model.  And Yes, it works!  I imported the battery in my 2.5.2 environment and it is attached to the connection of the user without any problem of disconnection.  I think that this remark made in the SR as well.

• Vista 64-bit Black Screen of Death, with just a mobile available slider, the system does not start in safe mode.

  My system worked properly on 25 April and then something happened and now the machine comes back with "Start menu options" but will not start in one of the listed options, modes result in the same outcome.  System also starts on the Vista CD.

  System begins to boot normally, shows the tracer Green Windows at the bottom of the screen, then the mouse pointer appears and moves but the rest of the screen remains black.

  That's it, that's all what he will do.  I checked the settings of the computer and ran the diagnostic tests available and everything seems to go fine and passes all the tests.

  I worked on my own computers for over 20 years and never been stumped before, but I must say this is a first, and I have no idea what to try to do it now.

  Help or direction is appreciated.

  original title: Vista 64-bit Black Screen of Death, with just a mobile available slider, the system does not start in safe mode.

  See if there is a way to tecover clean your data before doing a restore to conditions of factory that will wipe the drive of all.  You can use Knoppix http://www.knopper.net/knoppix/index-en.html with a good ISO as Copier: http://isorecorder.alexfeinman.com/isorecorder.htm as well as a blank CD (which you will need to do on another computer).  Starting on this disc and lla should give you enough access to the system (if you do not have any other means) to backup your important data.

  So since you seem to have no other alernatives, you can try retoring the original factory computer options. However, if it is a hardware problem as could very well be the case, you can still encounter problems after even this drastic step.  Then you will need to consider in a reputable computer repair shop (NOT Geek Squad or or a any of these big store centers) or maybe even go back to the manufacturer for repair.   Check out several options and compare the costs, quality and guaranteed and then make your best decision.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Computer will not start with Windows. I get a black screen and a blinking cursor.

  Windows XP Home Edition startup problem

  I have Windows XP Home Edition, but the computer does not start at the top.  I get a black screen and a blinking cursor.  I have an XP installation disc.  I was in the Recovery Console to recover all of the standard tasks, but nothing helped.

  Brand, model and model number of your PC?

  Are you able to get into the BIOS?
  What took place prior to this problem?
  For now, you can read this to get some ideas:
  http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm

• Need help with windows defender. all my files folders pictures everythiing disappeared and I find myself with this black screen and it is not all good: o)

  Need help with windows defender. all my files folders pictures everythiing disappeared and I find myself with this black screen and it is not all good: o)

  I don't know why vista windows no longer charge, or when the files and folders disappeared

  How Windows Defender is on this problem?

  Follow these steps to try to solve your problems of boot.

   

   

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite - black screen and can't restart with the recovery disk

  I have a black screen and can not restart with the restore disc but it seems to be.

  I find this odd, I can't ask Toshiba direct on my problem, but I have to wait for one nature in the heart of my problem or give me a helping hand

  Hey,.

  This means that you can see anything on the screen of the laptop or only if you try to start with the recovery disk?
  You can start Windows or access the BIOS?
  You must post a few more details, otherwise we can t help you :(

  Furthermore, Toshiba is not your first contact, you should ask an authorized service provider. They can help you too! :)

• Start black screen and beeps, HELP pls

  I have a HP Pavilion zv5410. When I turn it on it has a black screen and it beeps (1-2-2). I went on some sites about, but don't really understand what is happening.

  I put the new RAM in because that I was told by a techie, it was usually the RAM goes bad, but this did not help. I can't do anything with the BIOS because I can not even a screen to enter in info, even with an external monitor.

  I was told that I could get the data on my hard drive with a hard drive enclosure kit. I bought the kit box Rocketfish 2.5 inches, but it has a different connector (for individual pins where solid mieare 'PIN' this slide down into the connector of the laptop).

  Any ideas or suggestions. I'd appreciate any help.

  Thank you all,

  K

  It worked!  I feel so stupid for not trying to see if the plastic piece came out.  Thank you much for the help!

  Karen

• At the start of the laptop goes to a black screen and says invalid partition.

  Original title: can I PRO 1-2cpu (IBM Laptop) Xp.

  • Not long I Formated my Windows XP PRO 1-2cpu, thinking that he would have run faster, not a blue screen crash and eliminate any viruses that could in fact, now that its formatted I can't use, whenever I start the laptop it goes to a black screen and says invalid partition, I don't know what that means though.

    so my question is there a way I can restore the computer back to normal? However, I don't have a recovery disk.

  A lot depends on how reformat you your hard drive.  Most manufacturers have a recovery partition on the hard drive that can be used to reinstall the operating system. Access you this by pressing a button that appears briefly at the beginning of the boot process.  If you have reformatted the drive c: partition only you might be OK and can get by using this recovery partition.  Otherwise, if you reformatted all the hard drive, then your only alternative is to get a Windows installation CD, boot from this CD and reinstall Windows.   Contact your computer manufacturer for advice.

  HTH,
  JW