Black screen - mouse - will not start any other
HI -.
Windows 7. Tries to start, but ends up with the black screen of death and also shows a mobile cursor.
Try the drive of product recovery but ends up with the same screen... Try to watch a disc external hard docking station and can not read disk 'Local' - but can see the information of the HARD drive.
How can I get the product recovery disc to recharge on the hard drive?
My guess is that the restore disc is writing the information on the hard drive - but cannot access it.
Does anyone think this might be OK?
Hello Oscar
What model of laptop do you have?
You created the recovery DVDs?
Installation of recovery is completed correctly?
You now have this problem at first start after the installation of recovery?
You can boot OS in safe mode?
> How can I get the product recovery disc to recharge on the hard drive?
As much as I know there no mechanism to force the recovery disc to do this.
All you can do is set the BIOS to the default settings and try again.
I can't say for sure, but somehow, I think that your HARD drive is troublemaker.
Tags: Toshiba
Similar Questions
-
Satellite Pro L450D black screen and will not respond to any keys
Hello
My niece has used his Toshiba L450D for almost a year now and he really liked it, who was until last month. She turned on her laptop and when she presses the button of the mouse, the button cracked and he fell into the laptop.
Now my brother contacted Toshiba and I was told because it is under warranty it might return for repair because it was a common fault. Then he he packed in loads of air bubbles and a box to make sure it was safe.
A few weeks later he came back repaired but we were all shocked that the laptop was put in a very loose box and you could hear this rattling noise. When we turned on the battery was flat and we had a new boot menu.
As she installed it Windows 7 laptop would boot directly into Windows 7, but now after the repair of the laptop shows a menu black screen with as follows:
+ Windows 7 +.
+ Recover Windows to Factory Settings [active EMS] +.So we started in Windows and everything went well, but now after 5 or 10 or even 20 minutes, laptop displays a black screen and will not respond to keys or mouse movement. There is nothing on the screen its just black.
I started in SafeMode (which was more difficult with the new menu) and it does the same thing. I even managed to do a virus scan quick who took 3-4 minutes and was clean.
I would like some advice on what my niece is very angry, and it's difficult to explain what is happening to a child in the primary school.
Any help would be grateful.
Hello
Have you tried the option of HARD drive recovery?
If this is not the case, try to set the notebook back to factory settings using HARD drive recovery.
Turn on the device, press F12, choose repair my computer, then select Toshiba HDD recovery.I hope it will work!
-
I accidentally put 100 files on my desktop and it went to black screen and will not work
I accidentally put 100 files on my desktop and it went to black screen and will not work
Hello
Following methods and check if that helps.
Method 1:Step 1:
Start your computer in safe mode and check if it starts very well.
Step 2:If the system starts in safe mode, then there would be a third-party software, causing the issue to occur. I wish that you start your machine in a clean boot State. Clean boot helps eliminate conflicts of third party software.
Note: Follow step 7 to your computer as usual.
Method 2:
If this does not help, you can perform System Restore in safe mode.
-
can not start any other os that mac os install dvd
I can not start any version of windows or ubuntu on my mac pro 1.1.
Tried:
Windows 98
Windows 2000 Professional
Windows 2008 Server
Windows XP home
versions of Windows 7 Professional 32 & 64
Ubuntu 10.04 lts 32-bit
Ubuntu 14.04 32-bit and 64-bit
most will show a cd when you hold down the ALT to start up
and those that I could start supposibly to give me a symbol of apple in alternation with the no symbol.
searching the Internet, it seems many people have this problem.
Details of my machine:
Model name: Mac Pro
Model identifier: MacPro1, 1
Name of the processor: Dual-Core Intel Xeon
Processor speed: 3 GHz
Number of processors: 2
Total number of Cores: 4
L2 Cache (per CPU): 4 MB
Memory: 16 GB
Bus speed: 1.33 GHz
Boot ROM version: MP11.005D.B00
Version of the SCM (System): 1.7f10
Chipset model: NVIDIA GeForce 7300 GT
Type: GPU
Bus: PCIe
Slot: Slot-1
The PCIe track width: x 16
VRAM (Total): 256 MB
Provider: NVIDIA (0x10de)
Device ID: 0 x 0393
Revision ID: 0x00a1
ROM revision: 3011
The system version: Mac OS X 10.7.5 (11 G 63)
Kernel version: Darwin 11.4.2
Boot volume: OSX
Boot Mode: Normal
Ensure the virtual memory: enabled
64-bit kernel and Extensions: No.
We window directly on the hardware, you must install via Boot Camp
http://www.Apple.com/support/Bootcamp/
a 64 bit OS will not work unless you use an add-on as the EFI on 2006-2007 Mac Pros is only 32-bit.
The CD of Ubuntu 64 regular bits have to begin on older Intel Mac, as MacPro1, 1, because of incompatibilities EFI. You must download a special + mac CD of Ubuntu to work around this problem. To 11.04, you can get it here:http://cdimage.ubuntu.com/releases/11.04/release/
http://Forum.Netkas.org/index.php?topic=1123.90
Also:
-
My Apple Watch appears to be dead. The watch screen is black. I have not matched the watch and we tried pair again, but the iPhone doesn't seem to acknowledge that she and I can't manually pair either. Any ideas on what's going on?
Charge the watch first. Instructions here > check your battery and load your Apple Watch - Apple Support
If necessary, restart the Apple Watch.
You should force reboot your device as a last resort, and only if it does not. To force the restart your Apple Watch, press in and hold the side button and the digital Crown for at least 10 seconds, and then release both buttons when you see the Apple logo.
Try the assistance provided in this support article > If your Apple Watch does not load, or it will not turn on - Apple Support
And here > set up your Apple Watch - Apple Support
Apple Watch user's Guide will be useful > https://help.apple.com/watch/
-
Satellite A100 has a black screen and will not charge in the Bios
I bought a Satellite A100 - (model psaa8c-0fh00e) about 5 months ago. It was left overnight, which is not uncommon, and when I came back using about 15 hours later it was just a black screen. moved from the touch screen and keys, and nothing did. so I cold it starts and he died. I then turned it back as usual and the laptop turns on but the screen is completely black. It's not loading the normal Toshiba Bios screen.
Now my question: If there is any way I can solve this, I am familiar with computers and parts. I don't get this cause I've ever had to reflash the wood or something like that. I am unsure of how to activate and I really want to have to take it to a shop, any suggestions would be helpful.
Thanks in advance.
Hi Conrad,.
If your 100 starts normally (spinning HARD drive, optical drive LED flashes, fans turn etc.) then I suppose that your FL inverter or LCD screen is not. You can check this by connecting an external monitor to the laptop to see if it shows the normal display.
On the other hand if there is no activity at all portable computer turn when you turn it on then I guess you have an internal hardware failure, possibly the main card, which must be checked by a Service partner authorized Toshiba since the unit is still under warranty if it is only 5 months old.
Kind regards
-
Qosmio G40 - black screen and does not start
A bit of water on my laptop... (bought in 2007, guaranteed on)
I did not cut power at the time because it did not work properly...But, the next morning.
Start with a black screen, fan is too much work and I have a beep.
An and after a continuous short beep...I opened it and dry all (air cold & mild)... paper to remove moisture.
but screen remains black, a beep and the fan not working too.
Please help... What can I do?
Hey,.
It seems that water damged your laptop or at least some parts. In the worst cases, you need a lot of new pieces of equipment, but I don't think that an authorized service provider can help you diagnose this problem.
On the Toshiba site, you can search for them:
http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service providerContact them and ask for help. They will help you as much as possible. :)
-
Satellite L300 has only a black screen and will not load.
Mobile hit child around keys shortcut if, Esc, cap locks, fn etc loading upward on the web, top computer laptop has black screen and then tried to load up.
See screen for a moment and then is become black and now the laptop starts but the screen is black and nothing else happens.Can someone help
Thank you
Tony.Hello
You mean that you are not able to access the BIOS?
Have you tried to use the FN + F5 key combination to switch to view different devices? Select this check box. Maybe the output display has been switched to external monitor? :|If nothing will not help to remove the battery and disconnect the portable AC.
Wait for about 1 hour then reconnect both sides and try to turn on the laptop. -
Windows load with black screen and does not start after windows updates
Original title: load windows normally screen will not continue
I went to my computer tower and I chose to install updates when closing. I went back later to re - turn on my computer and now it loads to the top of the black screen that gives you 5 options. safe mode, safe mode with networking safe mode command prompt, windows loads normally and finally to load windows from last known configuration that works. Problem is that none of these options work. they all return me to the same screen. Help this laptop came preloaded with Win XP Media Center edition and I can't get back to work. IM assuming I need a XP disk support center but I can't find them anywhere! HELP PLEASE SOMEONE!
Hi Burton089,
Your hypothesis is right. To resolve this problem, we need to repair your installation of Windows using the Windows XP disk. We recommend that you contact the manufacturer of the laptop to check if they have the Windows recovery disk.
See perform a repair InstallationVisit our Microsoft answers feedback Forum and let us know what you think.
-
IPhone will not accept any other than the old ID
IPhone 5 and IOS WIN10 just installed a couple of days. Trying to synchronize or establish a link to ICloud/Iphone - IPhone can't forget OLD Apple ID I do not have a PW for or can answer questions of security. New Apple ID works on PC but not the iphone to ITunes but can't get phone off loop for old code. Any general approached, I can take. Already tried without success so far the Apple Support. Butcher
If you have enabled find my iPhone using the old Apple ID then the phone is off permanently unless you can remember the password. It is Activation Lock, a measure of deterrence of theft. There are several ways to get help to recover the password from https://iforgot.apple.comthen contact on behalf of Apple security team: Apple ID: contact Apple for assistance with the security of the Apple ID accounts
Your other option, if you bought the new phone, is to take the original invoice and the phone to an Apple store and they can remove the locking of Activation. But you must prove that you are the original owner.
But if none of these work you will never be able to use this phone again.
-
Satellite A200-13 M - black screen and will not turn off
Hello
I just bought a * Satellite A200 13 M *. In the first market, Windows Vista seems to be properly installed and worked to internet (wifi) access. The Norton program has been updated, and I could download and install OpenOffice. However, as OpenOffice had reported a small amount of disk space available (55 GB) I tried to see the hard drive in the browser.
I clicked on Control Panel and waited to open. At this point, the arrow of the mouse has frozen. After awhile, I tried Ctrl, Alt, Del, and the system asked if I wanted to stop. I did, and a new screen has announced that Windows is being closed. This screen froze then in turn. I waited for a while and then tried to turn it off with the switch. The screen went black.
However, the blue light comes on, the fan is still running, but I nothing seems to wake up the machine. I called the service of maintenance of the shop, I bought from (Darty), but they are overloaded and said they'd call me in a couple days (!). Is there anything I can do in the meantime that would allow me to continue to work with the machine.
Thank you
Tim Mason
Strange sounds! But it's a computer and sometimes, these machines don't {color: #ff0000} {color} strange things ;)
Anyway... try to remove the battery from the laptop and unplug the power adapter.
Wait about 20-30 min and connect everything again.Then try turning on the laptop computer. If it is not a serious problem, the laptop must again!
-
Satellite A135 black screen and does not start
I have a Satellite A135 with windows vista and I have not used in more than a year.
I went to use it today and it turns on but the screen is blank. I can't even see not the bios.I tried the usual things, connect to a monitor, removed the chip of ram from the back and tried another one, I also tried power alternative only with no luck.
All the ideas it might be.
Thanks for the help
Hello
If the BIOS page does not appear, then it s a serious question.
Seems that the motherboard is dead.In my opinion, a technician should check this section first, and perhaps you will need a new
Motherboards are parties, then perhaps it s not an option for you
-
Computer has a black screen and does not start. Vista of Aspire5535 Acer base
As above. Help please!
Hello
If when you start your Acer is no 'Acer' logo splash screen at all and nothing appears on the screen, which would indicate a hardware problem.
If under warranty, contact Acer.
If it is not under warranty, use a repair shop, local.
See you soon.
-
I have 72 emails to download, but it only downloads the first message and then stops and says no more messages. Tried to download these messages at least a dozen times, but get just one. I ran my antivirus, spyware and programs malicious, but it did not help.
Suggestions?Disable the e-mail scan in your anti virus suite.
-
Perform a hard reset
I added an external monitor and restart the computer. All seeing power are on, fan and hard make sounds and still nothing on both screens.
Reinstall all hardware
Still nothing but black on both screens.
Is it possible that a virus could cause black screen and does not start. Seems the laptop crashes, because all the lights remain.
Please notify.
Hi there @SVJ69
Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.
I understand that you get a white screen when you turn on your system. I'm happy to help you with this. I would recommend that you start with searching through this page. Since the construction in and external display do not respond, I would start with the displays.
Troubleshooting of black screens with no start-up or start-up error message
Problems related to laptop (Windows 7 and Windows 8) displaysThis can help more evenly. If another hand, you get error messages, or a repetitive pattern of flashing LED, let me know.
Maybe you are looking for
-
HP laptop model g080nr: f12 button wireless stay orange won' find the wireless network
After a update HP laptop does not connect to my wireless home button stay orange and I can't find my owner's manual to see what buttons to push with f12 to activate WiFi again, any help would be appreicated.
-
Need help, something took control of my system!
Something took control of my system, what I download, it reconfigures it to his advantage, I reinstalled the operating system 3 times. I pulled a temp file "summary, it says software strategy limited, enable, concealment and attempt to activate all p
-
I don't have my HP CD to load driver software on another computer. HP can't stand my HP OfficeJet 7210 all-in-One printer. Can what site I go to find the download of the driver/software on my computer. My computer has Windows 7 and my OS is 64-bit.
-
Hey, all! It was only a few days, I started using Windows Vista. Recently, I installed the AVG anti-virus free 2011 on my PC. But, after installation, when I scanned the computer with him, it displays a warning that there is a (potentially harmful Pr
-
Cannot create a new folder or cant find where it is...
I see the ability to create a new folder when I'm in my library, but when I choose to do, I don't see the folder! Help, please!