code value 43 device unknown 0000002b

Similar Questions

• Equium L40-156: graphics card problem - error code 12 in Device Manager

  People of the night...

  Just got a family run Vista premium, Equium L40-156, everything is going well except a little problem with the display adapter (Mobile Intel 965).

  Tried the drivers that I had with the installer
  Tried the drivers from the toshiba download page
  Tried the drivers on the Microsoft Update site
  Tried the drivers from the website of intel

  All have the same problem, in Device Manager, it shows with an error (the pretty yellow triangle with the "!") with an error code 12 (the device cannot find enough free resources) even after a system resart.

  Switching view hidden devices displays a 2nd same device, but works correctly, but the two disappear if I try to delete either.
  Display settings do not display a connected device, DXDIAG had no idea either.

  Latest version of the BIOS installed, all other devices are very good and can not see an IO overlap anywhere

  Any suggestions, greatly appriciated

  Ta

  Hello

  I have studied a little bit and looked on the Microsoft page for some answers and found out what exactly means the error code 12.

  ------------------------------------
  + Error code 12 +.

  + This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12) +.

  + Two devices are assigned the same i/o ports, the same interrupt, or the same Direct memory access channel (whether through BIOS, the operating system, or a combination of both). This error message may also appear if the BIOS did not allocate enough resources to the device (for example, if a (USB) universal serial bus controller is not an interruption of the BIOS because of a corrupt MPS (Multiprocessor) system table). +
  -------------------------------------

  Well, what to say; usually this error message should not appear with the original Toshiba preinstalled operating system.
  I put t know if you have changed something or add an additional device, but it would be very interesting to know if the same error message appears after the reinstallation of the OS.
  You can use the Toshiba Recovery CD/DVD of restoration!

  All the drivers, the tools are already preinstalled on the recovery CD so the entire procedure will not take very long. about 10 min.

  Check this box and report if the same error is displayed on the laptop with the factory settings!

  Good bye

• Satellite A110 - SD card reader - error message code 10 this device cannot start

  I have a number of cards memory SD, who used to work with the machine's card reader but now gives a code 10 this device cannot start, error message - is this a problem XP - ideas appreciated...

  Hello

  Well, it sounds to be really an XP problem. Eventually he s corrupt registry entry.
  Just try to remove the SD card from the Device Manager reader, and after restarting again try to install it again

  Next

• missing driver, other devices (unknown device)

  Hello

  Please I need the driver for this system;

  HP probook 450 G1

  Windows 7 Professional sp1, 64-bit OS

  other devices (unknown device), hardware id:

  USB\VID_138A & PID_003F & REV_0104
  USB\VID_138A & PID_003F

  Hello

  The driver you need is on the following link.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5405166&swItemId=ob_134806_1&swEnvOid=4058#tab3

  Note:  Make sure you have first installed HP customer Security Manager and Device Access Manager for HP ProtectTools.

  Kind regards

  DP - K

• Device unknown Base system-> card reader, ThinkPad T430 2349 Win7

  Hi all

  I got a new ThinkPad T430 2349 and installed Windows 7. After installing the drivers, everything works fine, except the card reader. It it is not found, on the contrary, there is a device unknown base system listed in the hardware Manager. The hardware of this base system device id is:

  PCI VEN_1180 & DEV_E822 & SUBSYS_21F317AA & REV_07

  This should indeed be the card reader.

  Should which driver I?

  I have already installed without success:

  http://support.Lenovo.com/de_DE/downloads/detail.page?docid=DS028931

  http://support.Lenovo.com/de_DE/downloads/detail.page?docid=DS029035

  Thanks for any help!

  Andreas

  OK, I had a driver that works in Windows 7, also:

  www.magnetix.rs/activa/E822_X64.zip

• My v3 wifi adapter - 112 p does not (broadcom) - code 10 in Device Manager

  does not my wifi adapter of v3 - 112 p - code 10 in Device Manager

  said-

  This device cannot start. (Code 10)

  {Operation failed}
  The requested operation failed.

  Can you do a right click on the card in the Device Manager and uninstall the adapter and restart the computer to see if that helps?

  If it doesn't, try to download and install the Win 10 wireless driver http://www.acer.com/ac/en/US/content/drivers.

• How can I activate my card Miniport Tun Microsoft? Get the error code (10) the device can not be started.

  Microsoft Tun Miniport adapt #2 /.

  Microsoft Tun Miniport Adapter #2 / it is disabled (code 22) / this device cannot start (code 10).  I need help to activate the network adapter.

  Description: Broadcom 802. 11b / g wlan - Packet Scheduler Miniport

  Device ID: root | * tunmp \0001
  status 0 x 01802401 has problem
  0x0000000a problem (10)

  Hi GGisin,
   
  -Did you change on your computer before this problem?
   

  Follow the steps listed in the article below for the mentioned error code:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  Note: The information provided in this article are applicable to other versions of Windows XP as well.
   
  Additional reference on:
  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

• Audio Realtek: code 10? Device cannot start.

  original title: audio realtek: code 10? Device can not start... I am running vista, but after a bad fall, I am now running xp pro 32 bit.

  I am running vista, but after a bad fall, I am now running xp pro 32 bit.

  Your sound card driver: http://www.realtek.com.tw/downloads/

  Check with your motherboard if the HD or AC97 card.

• DVD/CD RW optiarc dvd rw ad-7560 s ata device suddenly stopped working I get a "code 10 this device cannot start.

  My CD/DVD RW optiarc dvd rw ad-7560 s ata device suddenly stopped working I get a "code 10 this device cannot start.  I have uninstalled and still get this error.  When I put a CD in nothing happens.  It is not read.  Any suggestions?

  Hello

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows Vista Home Premiun auto restoration and backup; Save the error code: i/o device error (0x8007045D), file backup complete normar will not complete successfully.

  Device error Code: i/o Device (08007045D) error Code... trying to make a backup of normal file that goes all the way and then produces this error code.

  Hey Rodney,
   
  To resolve this issue, follow these steps:
  1. Click Start, type cmd in the start search box, right-click cmd.exe in the list programs and then click Run as administrator.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  2. at a command prompt, type the following command and press ENTER: Chkdsk/r X:
  Note: In this command, x is a placeholder that represents the drive letter of the volume you want to check.
  3. press y when you are prompted to check the drive the next time the system restarts.
  4. close all applications and restart the computer.
  Note: When you restart, Windows checks the drive for errors, and then Windows starts.
  5. after the computer restarts, repeat steps 1 through 4 for the other volume and try the backup operation again.
   
  For more information, see this article: http://support.microsoft.com/kb/952272
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• error code 12 in Device Manager with graphics card intel HD.

  I buy a system with the following specifications.

  Win 7 ultimate 32 bit
  with intel motherboard DH61WW

  When I install the drivers for the graphics card, I got error in the management system saying code 12
  "This device cannot find enough free resources that it can use. (Code 12)

  If you want to use this device, you will need to disable one of the other devices on this system. »

  I have the latest version of the driver software

  Thank you Sir,

  I solve the problem by myself...!
  There was a reader of "AMD 3gIO filter" problem is a conflict I do system restore and install the new driver successfully...

• How can I get the IMEI code of the device?

  Hello world.

  I have a problem. I need to get the IMEI code of the device. How this could be done?

  System.getProperty ("IMEI") returns null.

  Phone class provides only the possibility to obtain the phone number.

  I use BB JDE 4.6.0 application developed for the peripheral BB 9000.

  Could someone help me?

  Thank you

  Maksym

  GPRSInfo.imeiToString(GPRSInfo.getIMEI(), false);
  

  P.S. This only works on GSM/UMTS phones. It will not work on CDMA phones or iDEN.

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• Activity Code values are not displayed in the drop-down list of choices

  I added a P6 activity Code (seller) and added some code values it contains. I'm in a position successfully, choose this option in the selected columns list, but when I go to select a value from the drop down, no values are displayed.
  
  Advice on why this happens or how to fix?
  
  Thank you
  Bill
  
  Published by: user12451419 on 18 June 2012 10:47

  When you assign a code by clicking on the column, a window opens. At the top of the window, click on the view bar, and then choose filter by > all values.

• EliteBook 2560p - XB208AV: 2560p another device - unknown driver

  Hello

  I recently bought a laptop computer that has been upgraded from Win 7 to 10.

  I have unknown showing peripheral

  Properties - details - value ACPI\HPQ0004\3 & 33FD14CA & 0

  Could you tell me what it is and how to make it work.

  Also

  The SD card reader does not work

  The Webcam does not appear in all devices. but it seems that, as there is an on-board camera installed.

  Everything else seems to work very well

  Used as a stand-alone computer on the home network wireless

  I searched through many web pages trying to solve, without success.

  If you have any additional info that might help me sort. I would really appreciate it.

  Thank you

  Nemo

  Hi Paul

  This seems to have solved the problem.

  Thank you very much

  Also, I've now sorted the webcam via the BIOS.

  All I have to do now is difficulty the SD card reader.

  Concerning

  Nemo