Help to configure SRW208G

Similar Questions

• I need help for configuring security for my wireless again.

  Need a help for my Wi - Fi Protected Access set up again... somehow I deleted it while trying to access the networks wireless outside my house.

  original title: Wi - Fi Protected Access

  Hi dmcangus,

  See the Microsoft articles below for more information on WPA wireless security.

  Configure Security Wireless WPA for home networks

  http://Windows.Microsoft.com/en-us/Windows-XP/help/networking/configure-WPA-wireless-security

  Overview of upgrading security Wi - Fi Protected Access (WPA) in Windows XP

  http://support.Microsoft.com/kb/815485

• 32L4333DG TV - need help with configuring WLAN

  I bought a flat 32L4333DG of Toshiba, but cannot configure the wireless connection.
  Help me please.

  Message was edited: assignment has been translated

  What's the problem? Have you read the instructions in the manual how to connect WiFi TV?

  There are 3 different methods to configure the WLan configuration:

  _1) easy Setup (WPS) _
  + If the AP is WPS compatible, this method can be used. +
  + WPS is a standard of the industry, designed to facilitate the wireless LAN connection and security settings. WPS automatically configures all the wireless settings. +
  + NOTE: WEP encryption is perhaps not able to configure through easy implementation. +

  _2) assisted Setup (installation using notification s AP information) _
  + Name network, authentication and encryption are decided according to the information provided by the AP. You can manually set the security key. +
  + The security key must conform to these conditions: +.
  + TKIP/AES: ASCII 8-63 or 64 Hex characters +.
  + WEP: codes ASCII 13 5 or 10 or 26 Hex characters +.
  + There's a key ID to set for the WEP encryption. +

  _3 _) manual configuration (manual entry of all parameters)
  + Some types of encryption are only compatible with specific authentication types. +
  + When authentication is an open system, only WEP or none is compatible. +
  + When authentication is shared key, WEP is compatible. +
  + When authentication is WPA - PSK or WPA2-PSK, TKIP or AES is compatible. +

  + When the inconsistent authentication/encryption pairings are detected, a warning message will be displayed and no connection attempt will be until the conflict is resolved. +

  + There's a key ID to set for the WEP encryption. +

• Help text Configuration file reading

  Need help...

  I try to do a VI that will read a simple text configuration file.  The file will have entries like:

  URL = 192.168.0.1

  Port = 9000

  What I want to do is read the line and 'analyze' in 2 channels.  Then, based on the content of the first string (the part before the = sign), do something with the second part (after the =).

  I managed to open the file using "File open/create/replace" and but will have problems reading "Scan From File" to pull strings (it seems to define a mistake when I read in the first line, although my probes show that I had two channels).

  Anyway, once I have my 2 strings, it is a simple 'case' as the structure that I can use to search through all my "pre-defined first?

  Do not build something new. Just use the file Config screws - check under file IO functions. They will do exactly what you want.

  Mike...

• HP C4580 not scan to PC. I need help to configure my Netgear router please :)

  Hello

  I've read here, the threads that talk about this printer prints only not to or from a PC - my problem is that the C4580 go scan from my PC, but will not scan to PC.

  I found an answer from someone who has had the same problem earlier this year, but I do not understand what to do.

  Here's the answer:

  "I have ordered mine entering the settings from my router (Netgear) page and setting the built-in firewall rules. "The internal firewall was blocking the printer, I could print, scan using the computer, just could not scan from the printer to the computer.

  Also, I have a Netgear router, but could do with help on how to do the same thing as the person above.

  Thanks in advance for any help!

  Sorry, I don't need help after all

  It was not the router requires a configuration, it is the firewall that was a block that should be changed to "allow".

  My "all-in-one" now does everything it is supposed to do

• RE: router wrt310n - need help for configuring wireless security

  I can get wireless if the router is not secure, but cannot configure wpa and wireless security.  Instructions followed on linksys tutorial but still connect wirelessly if I select wpa security.   In addition, I can't find a way to change the ssid, the pages of router do not match documentation.  The version of my router is v1.  Is this obsolete, I know that there is a v2.  Any help will be appreciated.

  Please follow these steps to configure the wireless settings and try to connect to the wireless network.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Fix the Radio band to wide - 40 MHz and change the broad Channel 9 and channel Standard 11 - 2, 462 GHz... Wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  IF YOU ARE NOT ABLE TO CONNECT TO THE RADIO

• Need help to configure the VLAN on a powerconnect 5448

  Hello world

  I am currently working on 2 switches PowerConnect 5448 but I'm completely lost in configuring VLAN.

  My bow:

  

  My needs are:

  -J' have 2 different networks that need to be isolated in different VLANS

  -I want to port 11-14 to use for network backup, all others must be used for the production network.

  -This 2 networks must pass through the port 48 (fiber)

  How can I configure this kind of network on the powerconnect interface (or via telnet)?

  My understood are the following, I have to create 2 different VLAN tag all ports, switch to safe mode all ports of the entitlement each port to the VLAN voted. Am I wrong?

  How the fiber port?

  Thanks in advance for your help on this matter.

  Since your 2 VLAN need not communicate with each other, you should be able to get this working.

  The easiest way to do this would be to have your production on VLAN 1 and VLAN 2 second network.

  Assign an IP address to the switch with the command IP #.

  Assign a default gateway with the # ip default-gateway command.

  Create a VLAN 2:

  Database console (config) # vlan

  Console (config - vlan) # vlan 2

  Set 11-14 ports to access the mode for VLAN 2

  Console # switchport mode access

  Console # switchport access vlan 2

  Set 48 on trunk or general mode ports.

  Console # switchport mode Trunk

  console # permit trunk switchport vlan add 2

  You should get pretty close to a work environment. You may encounter some problem with VLAN 2 contacting 192.168.1.0, maybe just need to put it up and test.

  Here are a few links to software packages and manuals that can help.

  Firmware.

  http://Dell.to/1tz8tW0

  Manuals.

  http://Dell.to/1yqV4DJ

  Keep us on how will your configuration.

• Help to configure the router Cisco 1941

  Help!

  I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

  Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

  Help, please.

  Hello

  Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

  Configure the terminal

  username username privilege 15 secret PASSWORD

  IP http server

  local IP authentication

  Sent by Cisco Support technique iPad App

• Please help to configure the router for internet connection 871W!

  Hello world!

  I just started styding for CCNA, so I'm totally new to Cisco stuff. Recently bought a router 871W and spent two days in a row trying to configure internet connection with no luck! I use the port console for the configs and SDM/CCP. Would be greateful if someone could tell me how to do simple configs of internet connection. I googled everything but it's still confusing. I can't assing all-IP ports FA 0-3. I used instead of the VLAN. But all tutorials use FA0 and when I try to assign an IP address to FA0 it gives me some L2 cannot be assigned or something... :/ And I am also confused at what address IP use for WAN.

  I connected the cable between the Modem and the LAN of the PC port and copied some IP addresses which I think I have to use to configure the router for internet connection. And here they are:

  ISP IP: 76.114.54.255

  SUBNET: 255.255.248.0

  GATEWAY: 76.114.48.1

  DHCP: 69.252.97.4

  DNS: 75.75.75.75

  75.75.76.76

  If you can, please help! Thank you!

  Hi david,

  Looks like your 871w can not get a dynamic IP address: % unknown DHCP problem... No possible allocation

  you could ask your ISP to perform a reset/clear MAC add and try again?

  also, kindly post lastest "show run".

  Edit: just to see you've updated your screenshot. could you add command under 4

  Mac-add 0001.4af9.8b83

• Helps to configure a Cisco 4402 wireless controller

  Hello

  I need help setting up a Cisco 4402 Wireless Controller. I want to have users automatically connect to the wireless network, but not to have access to all the resources network until they open a web browser and provide their domain user name and password or a guest account provided by the receptionist.

  I tried many different configurations but can't seem to make it work properly. More time then not when I put on the WIFI network security it causes my wireless network to disappear from the list of wireless avaialbe.

  Here's my network configures:

  1 - 4402 wireless LAN Controller

  2 - Aironet 1130AG antennas

  1 - 5510 cisco ASA

  1 - 4503 core Router\Switch

  8-2960G switches

  Windows domain Server 2003 with RADIUS running on the domain controller.

  Thanks in advance for the help.

  Glad you got it working...

• Need help with configuration of VLAN SF300-24

  Hello

  Let me Preface this with the fact that networking is certainly not my point hard, so here, any help is greatly appreciated.

  I'm trying to segment on a virtual desktop on its own VIRTUAL local network infrastructure using a Cisco SF300-24 Layer 3 switch. I can get the switch to connect to the network with the assigned VLAN 1 an IP address on the subnet of the network (192.168.16.X), but I can't get anything this is set up VLAN 20 (192.168.20.X subnet) to connect past the VLAN 20 (192.168.20.254) gateway IP. The ports assigned to 20 VLAN are defined to access the mode if it matters.

  Here is a diagram to illustrate what it looks like, as there is another (L2) switch involved.

  

  So I'm not really sure what I am missing here since all settings seem simple enough.

  Hi Simon, I recommend you remove any server active directory and essentially remove all safety factors. This will give the idea of where to start.

  If you take a quite basic set, 2 Windows 7 workstations without a Firewall window activated, they both work as expected.

  It must be remembered that in firewalls, even if they are able to respond to ICMP if the request is from a different subnet, they will not be because he is recognized as a network abroad. You must know the network on these computers or make sure the computer does not care.

  You may be able to do this by simply adding additional subnets on the advanced configuration of the network card (if it does not take too much address space) as an example.

  Or well, as you have discovered that you can add routes, which is a bit heavy and inconvienent, but effective.

  -Tom
  Please mark replied messages useful

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• WLC 5508 + AP 3502i + help ACS configuration

  Hello

  I have a Cisco 5508 WLAN controller and three Access Points 3502i Cisco a Cisco ACS 5.2. I need to set up a simple wireless authentication system where a user is prompted to enter a user name and password in a web portal before you can access on the wireless LAN.  Usernames and passwords are available in a CSV file and would need to be entered in the TAS.

  I read several guides from Cisco, including the WLC configuration guide, but I'm still confused.  If anyone can please give me advice on how I could set this up, I would really appreciate it.

  Thanks to a bouquet.

  Well first of all set up a ssid for Webauth.

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_e...

  I would also first start by creating a local user on the WLC net and try to get this to work first. The link I posted has this info. With the help of ACS is a little tricky but can be done. The WLC has of a Hall admin function that can help if you need someone else enter the user name and password. I tend to use ACS for all internal authentication.

  Sent by Cisco Support technique iPhone App

• helps bridge configuration

  Hi all

  I try to fill 2 VLANS using 1 one ssid but failed. The APs are Cisco AIR-AP1242AG-A-K9. Here is the configuration. Please help find the problem or share a sample of the configuration. Thank you very much.

  -------------------------------------Root Bridge-------------------------------------------------------------------

  Root #sh run
  Building configuration...

  Current configuration: 1834 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  name of host root
  !
  enable secret 5 $1$ qvkA$ iCQUBDBCeHOS8qVo7RhaS.
  !
  No aaa new-model
  !
  !
  dot11 syslog
  !
  dot11 ssid CS832A
  VLAN 28
  open authentication
  shared authentication
  authentication-key wpa version2 management
  infrastructure-ssid
  WPA - psk ascii 7 06575F706A1D594D5D45455B5D507F7B007D6B6606
  !
  dot11-arp Optionally cache
  negotiating inline power injector substitute
  !
  !
  05280F1C2243 Cisco 7 password username
  !
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption ciphers aes - ccm mode
  !
  SSID CS832A
  !
  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0
  no short preamble
  channel 2412
  station-role root bridge
  !
  interface Dot11Radio0.10
  encapsulation dot1Q 10
  no ip route cache
  Bridge-group 10
  !
  interface Dot11Radio0.28
  28 native encapsulation dot1Q
  no ip route cache
  Bridge-group 28
  !
  interface Dot11Radio1
  no ip address
  no ip route cache
  Shutdown
  DFS block 3 Strip
  channel SFR
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  !
  interface FastEthernet0.10
  encapsulation dot1Q 10
  no ip route cache
  Bridge-group 10
  !
  interface FastEthernet0.28
  28 native encapsulation dot1Q
  no ip route cache
  Bridge-group 28
  !
  interface BVI1
  IP 192.168.28.11 255.255.255.0
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end
  Root #sh ip int brie
  Interface IP-Address OK? Method State Protocol
  BVI1 192.168.28.11 YES manual down down
  Unordered Dot11Radio0 YES TFTP upward upwards
  Dot11Radio0.10 unassigned YES unset upward, upward
  Dot11Radio0.28 unassigned YES unset upward, upward
  Dot11Radio1 unassigned YES NVRAM administratively down down
  FastEthernet0 unassigned YES NVRAM up up
  FastEthernet0.10 unassigned YES unset upward, upward
  FastEthernet0.28 unassigned YES unset upward, upward
  Virtual-Dot11Radio0 unassigned YES TFTP low low
  Virtual - Dot11Radio0.10 not assigned YES unset down down
  Virtual - Dot11Radio0.28 not assigned YES unset down down
  Root #.
  Root #show dot11 bssid

  Comments interface SSID BSSID
  Dot11Radio0 001a.302e.01e0 not CS832A
  Root #.
  Root #.
  Root #show dot11 Association
  Root #.

  ---------------------------------------------Non-Root Bridge----------------------------------------------------------------------

  Non-Root #sh run
  Building configuration...

  Current configuration: 1857 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  Non-Root host name
  !
  enable secret 5 $1$ RJ4C$ WDM/tBrstgdLxdOQcm6YO /.
  !
  No aaa new-model
  !
  !
  !
  dot11 ssid CS832A
  VLAN 28
  open authentication
  shared authentication
  authentication-key wpa version2 management
  infrastructure-ssid
  WPA - psk ascii 7 06575F706A1D594D5D45455B5D507F7B007D6B6606
  !
  dot11-arp Optionally cache
  negotiating inline power injector substitute
  diet pre-standard trading online
  !
  !
  05280F1C2243 Cisco 7 password username
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  encryption ciphers aes - ccm mode
  !
  SSID CS832A
  !
  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0
  no short preamble
  station-role nonroot bridge
  !
  interface Dot11Radio0.10
  encapsulation dot1Q 10
  no ip route cache
  Bridge-group 10
  !
  interface Dot11Radio0.28
  28 native encapsulation dot1Q
  no ip route cache
  Bridge-group 28
  !
  interface Dot11Radio1
  no ip address
  no ip route cache
  Shutdown
  DFS block 3 Strip
  channel SFR
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  !
  interface FastEthernet0.10
  encapsulation dot1Q 10
  no ip route cache
  Bridge-group 10
  !
  interface FastEthernet0.28
  28 native encapsulation dot1Q
  no ip route cache
  Bridge-group 28
  !
  interface BVI1
  IP 192.168.28.12 255.255.255.0
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  Non-Root #sh ip int brie
  Interface IP-Address OK? Method State Protocol
  BVI1 192.168.28.12 YES NVRAM low low
  Dot11Radio0 unassigned YES manual reset down
  Reset Dot11Radio0.10 unassigned YES unset down
  Reset Dot11Radio0.28 unassigned YES unset down
  Dot11Radio1 unassigned YES NVRAM administratively down down
  FastEthernet0 unassigned YES NVRAM up up
  FastEthernet0.10 unassigned YES unset upward, upward
  FastEthernet0.28 unassigned YES unset upward, upward
  Virtual-Dot11Radio0 unassigned YES TFTP low low
  Virtual - Dot11Radio0.10 not assigned YES unset down down
  Virtual - Dot11Radio0.28 not assigned YES unset down down
  Non-Root #.
  Non-Root #show dot11 bssid

  Comments interface SSID BSSID
  Dot11Radio0 003a.9889.50a0 not CS832A
  Non-Root #.
  Non-Root #.
  Non-Root #show dot11 Association
  Non-Root #.

  Did you put this unit through CLI?

  I highly recommend do you by GUI (Internet explorer)

  There are a few mistakes...

  Initially this remove the SSID configuration:

  shared authentication

  Then apply encryption AES - CCM vlan native (28)

  Let us know how it goes...

• Help to configure Cisco VPN configuration

  Hi guys,.

  I need help in the configuration of the VPN from Cisco IOS. Basically, we have 2 routers of cisco 1811 in our society.

  1. Router 1 - router (IP 192.168.x.254) of Production
  2. Router 2 - router VPN (IP 192.168.x.251).

  All computers/servers within our network has been configured with a default 192.168.x.254 gateway. Therefore, all internet traffic through the router to the production.

  Now, we want to deploy a new router (Router 2) which will be used only for purpose VPN (for example, DMVPN, IPsec site-to-site, configuration of the client VPN etc.).

  I have configured the router with Cisco VPN client 2 and can connect to this by using client applications VPN from my pc at home. However, once I connect to it, I'm not able to ping anything inside this network other than the IP Address of Router 2 (192.168.x.251).

  Is there something else I need to put in the configuration, so that I can ping everything inside the network?

  Any help would be greatly appreciated.

  Kind regards

  Vignesh.

  Vignesh salvation,

  I assume that you have created a new pool of vpn for remote access on Router 2 clients?

  If so, you will need to have a route static (for the range of pool VPN) on Router 1 to Router 2.

  I would like to know how you...

  Please rate this post if helpful.