HP ENVY 17 - 3070NR: cloned OS of the HDD to the SSD.

Similar Questions

• HP-envy-15-j118so: Does hp-envy-15-j118so (AMD processor) supports the SSD

  Hello

  I have a hp envy 15 j118so with AMD processor.

  I'm planing to replace my SSD HDD HARD drive.

  I was reading through the forums in orer to find a good way how to and I found the manual below

  http://h10032.www1.HP.com/CTG/manual/c04091768.PDF

  He mentions the manual it's

  256 GB SSD (for models equipped with an Intel computer)

  This means that my PC does not support SSD as I AMD Quad processor?

  Thank you

  Don't listen to this guy. It is a straight copy and paste and that's all. SSDS is supported by anything that uses the SATA interface.

• Laptop HP ENVY 15 t-k000 CTO: replace the SSD HARD drive in HP ENVY 15 t-k000 CTO Notebook PC

  Hello people,

  I know it took a lot, but I find a hard time to see the correct answer specially for my device

  I have a HP ENVY 15 laptop that has a hard workout 931 GB Hitachi-HGST SCSI Disk Device (SATA).  What are the compatible SSD should I buy to replace this drive?

  Is it good to buy hybrid SSDHD like the seagate one? http://www.Seagate.com/internal-hard-drives/solid-state-hybrid/laptop-solid-state-hybrid-drive/

  Any recommendations?

  Sorry that I've never tested with hardware before however, I wanted to update until the initialization of the time takes about a minute since it has a core i7 intel and 8 GB of RAM.

  Thank you

  Reinoa

  The best consumer SSD there is a Samsung 850 Evo. It will have the same physical dimensions as a hard drive. 2.5 inches wide and 7 mm thick. A 7mm form factor fits anywhere the will of 9.5 mm. The connectors and mounting holes are in the same places so that they are interchangeable.

  http://www.Amazon.com/Samsung-2-5-inch-internal-MZ-75E250B-am/DP/B00OAJ412U/ref=sr_1_1?s=PC&ie=UTF8&QID=1442231068&SR=1-1&keywords=Samsung+Evo+850

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP ENVY 17-j101ex - replace the SSD HARD drive

  Hello

  I have HP ENVY 17-j101ex, with the standard configuration: 2 x 1 TB drive HARD 5400 RPM SATA. I want to buy 1 SSD drive and replace the first (boot) hard disk drive. I don't know if it works or not.

  I want to buy a SSD Samsung 840 EVO 250 GB SATA III (MZ-7TE250BW), 2.5 ", dimensions: 100 x 69 x 7 mm

  I have to: 1 x 1 TB HARD drive (as a secondary drive) + 1 x 250 GB SSD SATA3 (as your startup with system disk)

  Is this ok?

  I found some info, that:

  Supports a 6.35 cm (2.5 in) 300 GB or 160 GB SSD (SSD) drive in 7, 0 - mm (. 28 - in.) thick

  Supports 6.35 cm (2.5 in) hard disks to 12.7 mm (. 50-in) and a height of 9.5 mm (. 37 - in)

  Is it not this Samsung SSD too big?

  I also found information on envy 17 series, which:

  Supports the following single hard drive/solid-state drive combination configurations:
  ● 1-TB, 5400-rpm, 12.7-mm hard drive × 1 + 300-GB solid-state drive
  

  and also:

  NOTE: Supports RAID-0 as default for all dual hard drive/solid-state drive combination configurations.
  

  So, first of all should I disable RAID-0?

  Thank you for your help and sorry for my English

  In fact, I have the same model laptop PC series. You will have no problem replacing the mechanical main hard drive with an SSD. The Evo to Samsung 250 Gig is a very good choice. I suggest you get cloning software, put the SSD in the second slot, start from cloning software and copy (clone) the startup disk for the SSD. You'll slim down the contenst of the diskette of starting less than 250 concerts to achieve, but you can store files off to the second disk of 1 TB in the process. There are other ways to do this post if you have any questions.

  Here is a video showing how to install the hard drive.

  https://www.YouTube.com/watch?v=wx3dMGXrGCc

  RAID-0 is supported, but you wouldn't want as a second hard drive with an SSD. If your readers are appearing as volumes of letters separated in 'the PC' or 'Computer' then RAID-0 does not exist and you shouldn't have to do any disorder in the BIOS.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP Envy 17-3070NR: what is the Max RAM for HP Envy 17-3070NR memory

  What is the configuration of memory of RAM MAX for my notebook of HP Envy 17-3070NR?

  Currently configured with chips of memory 2 x 4 GB DDR3.  I see conflicting card (8 GB and 16 GB) between various online sites like CNET and NEWEGG

  @BR_WLPhoto

  Supports up to 16384-GB of RAM @ 1333 MHz, supports up to 8192 GB RAM @ 1600 MHz

  Your manual here.

  http://h10032.www1.HP.com/CTG/manual/c03317166

  REO

• I can't find Wireless Assistant to my HP Envy 17 3070NR

  I can't find Wireless Assistant to my HP Envy 17 3070NR.  The Maintenance Center also does not show.  Where can I download it?

  The goal is to change the configuration for connecting the ethernet cable (connecting to the intranet using a fixed IP address), you do not disconnect wireless.

  Thank you

  Chris

  Hey, Chris:

  Sorry, there is no LAN/WLAN switch in the BIOS of envy.

  I doubt that the wireless assistant will do anything.

  What is manage your wireless devices, but what do you have to lose by trying?

  Most likely, it is not a program that is supported on your PC, this is why it is not listed.

  I have provided the link to the latest version available...

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3688868&swItem=ob-87841-1&mode=5

  Paul

• Nine (3 days out of the Box) HP Envy 700-230qe automatically restarts after the initial boot...

  I have now a whole new desktop 700-230qe HP Envy (after about a month in the loop of the HP Technical Support).  But again, I have problems.  I took late delivery December 23, 2013.  After giving him enough time to become the temperature of the room, I opened the box and replaced my old HP Pavilion h8 - 1210t with envy again desktop computer.

  Took my time and made sure that everything is properly connected - then pushed the power button.  Everything seemed to work perfectly - until what the brand 20 minutes - when the system powered off and rebooted itself.  But for the rest of the session, everything went well - no problem.  It was Monday night.

  On Tuesday morning (December 24, 2013 - on Christmas Eve), I pushed the power button once again and the system started fine.  But 20 minutes later, it turned off and rebooted itself.  But for the rest of the day everything went well - even if I had to make several reboots all reinstall my applications and migrate my data.  I started to wonder if I still had problems.

  Christmas day (December 25, 2013) is the same thing.

  And once again on Thursday (December 26, 2013) - I finally called HP Technical Support.  I spoke with a gentleman (Terrence) - he accessed remotely my system which makes me nervous (but these guys of Nova Scotia are very good and are savvy customers.  He looked around - ran MalWareBytes and CCleaner - and said that he saw nothing thaat would be a problem.  We agreed to wait a day and see what would happen.

  Rolled Friday autour and you'd know it's the same thing.  Then, I called HP Tech Support and spoke to a lady (Norma) who, after having read the file of description of situation and asking me my name, phone number, email address (which they ask you every time you call - you would think they write this stuff and keep it on file), she immediately decided that the best thing to do is to 'Recreate the IMAGE' on my drive - to which I replied 'NO WAY '.  This seems to be the standard response, if they can't fgure out - recreate the image on your disk.  They don't seem to care about all the work you put into the construction of our system with applications with associated and all data - they want to just Blow-It-Away.

  It made me so angry that I have immeddiately contacted my case manager company HP with the history.  These people - business - case do an excellent job, at least the one I did a great job.  And I know she'll get to the bottom of this situation and go to a happy camper.

  Anyway, if anyone has the same problems with their machine - I'd be interested.

  Kind regards

  Garth

  <>>>>

  I did not read all the answers, but what my qestion... Why are you screwing around? HP has a 21-day return policy, so you can ask them to replace it with the same model or another model as they will send you a FEdEx shipping for a full refund or Exchange label. I wouldn't waste my time with a question like this on a new computer.

• HP Envy 4500: HP Envy 4500 - photo print half off the page. Print very well.

  All of a sudden, my HP Envy 4500 failed to print all the images; documents continue to print OK.  For photos, the printer acts like it's works fine to start, but print only about half of the photo on the paper - it seeks to print the rest on the back of the photo a lot of ink rollers...

  Research forums, this is the EXACT problem I have:

  http://h30434.www3.HP.com/T5/inkjet-printing/HP-envy-4500-prints-only-half-of-the-photo/TD-p/3781222

  I have uninstalled/reinstalled drivers, try to print from a different computer, laptop and even tried what was suggested in the post above - to copy a picture of the scanner on the printer itself.  Who printed still only half of the picture...

  The consensus from the link above was a hardware problem.  My printer is no longer under warranty, so unless there is another thing I can try I will buy a new printer.   This one isn't worth it for me to pay to ship somewhere to remedy.

  Any last suggestions until I have this gift to local traffic (with a note that it only prints documents)?

  Hi @JPotter,

  You can contact HP customer care to find out what service or the recovery options are available. Check the model number and the form to receive a file number for faster assistance.

  Thank you!

• Replacement of the SSD for HP Envy 15-J160!

  Hello! I want to change my hard drive in my HP Envy 15-J160, a new SSD. It will work with any SSD? Anything else I should be thinking? There are no guide for this on my specific model?

  Thank you in advance!

  Here is the Service Manual:

  Manual

  See page 45. Yes, you can replace the hard drive with an SSD. Don't know what your budget may be, but here is a page showing all sizes of Samsung 850 Evo:

  http://www.Amazon.com/Samsung-2-5-inch-internal-MZ-75E500B-am/DP/B00OBRE5UE/ref=sr_1_1?ie=UTF8&QID=1444600313&SR=8-1&keywords=Samsung+850+Evo+500

  You should get at least one concert 250 and preferably a 500 gig. The old disk can be copied (duplicated) in the new SSD, or you can use the HP recovery discs.

  Simply connect the SSD drive exactly like a hard drive. There is nothing you need to do for the BIOS or anything else unusual. Just plug in, install the software and go.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP dv7-6b50eb: HP recovery launches the cloned SSD, impossible to install win7 on the SSD.

  Hello

  I recently bought an SSD to accelerate my HP DV7. So I tried to clone my previous 1 TB to my 250 GB SSD hdd, but it seems that it's quite simple. :-(.

  I have created the exact same partitions (with the same size, orders, except for my main Windows partition type of course being given my SSD is much smaller) on the SSD as on my old Hdd. After that I made an exact copy of each 3 partitions (HP Recovery partition, system and tools Hp) but instead of copying the windows partition, I left a void on the SSD as the size of the Windows on the old hard drive partition is larger (the data) than the available size on the remaining on the SSD partition. I thought that I could boot on the SSD drive and start the restore process to install Win7 on the empty partition. But when I restart the pc, it does not seem to recognize the boot SSD partition, he prefers not to say "No operating system found".

  I also tried to activate the 3 partition directly (which is the recovery partition) to directly on boot as the partition, but it did not work either. The partition to activate before it was the 1st partition (which is the SYSTEM partition), but he has not worked either.

  Can someone help me do that cloning to work?

  FYI, I did the cloning and the creation of the partition using fdisk and dd on ubuntu.

  Thank you.

  Hi Wawood and Mista B,.

  Thanks for your comments I have a previous message, but strangely I have not found trace of the previous message, maybe I forgot to press the 'POST' button:-s.

  In any case, I was thinking that I understand your remarks Wawood but my goal isn't specifically for the windows on my new SSD partition (not interested in reducing the windows partition, it is just a statement), it was ok for me to any re - install from the recovery partition, a windows 7 from scratch.

  And I'd say Mista B by saying that it would have been stupid HP do not allow someone to use the recovery on the same pc partition, just because it has a different hard drive.

  Finally, I managed to do what I wanted to for those who are interested (HP is not so stupid after all:-p), here's the method I used to clone my hard drive of 1 TB to my 250 GB SSD and keep all the native HP (recovery, hp_tools, System) partitions with a 1 TB hard drive works correctly.

  So what I have is:

  -J' put the SSD as a second drive on my laptop (I guess it should work in the same way if connected by USB)

  -J' I started my pc and downloaded the EaseUs partition master

  -J' ran the program and began by doing a thorough cleaning of the SSD

  -J' made a copy of the system partition of my hard drive of 1 TB to my SSD

  -J' made a copy of the partition my hard drive of 1 TB HP_TOOLS to my SSD

  -J' made a copy of the recovery of my 1 TB hard drive partition to my SSD

  -J' created a new empty NTFS partition in the remaining partition

  I'm done with the same exact score as agenda in my 1 TB HDD.

  1. THE SYSTEM

  2 NTFS empty

  3 recovery

  4.HP_TOOLS

  After that my SSD was not bootable, because the MBR has not yet been copied.

  Then I started a live CD of Ubuntu and I installed boot-repair and he ran.

  I chose the advanced options and set set the mbr and boot from the partition 3.

  I then put the partition recovery (partition 3) as being ACTIVE.

  I removed the hard drive of 1 TB of the laptop (to avoid any error during execution of recovery which ends with the recovered 1To:-p) beeing and replaced it with the SSD.

  I then rebooted the laptop and it starts directly on the recovery partition. I finished in the recovery strategy (I could not choose the recovery from an earlier point in time given that the windows partition is empty (no windows backup)).

  I chose over the full restore, the slight recovery with only OS and drivers and it does the job of recovery. Now that the of what I write this resolved thread :-).

  Hope this helps some people out there with the same questions.

• The HP Envy 17 laptop Quad t allows the base to extend HP xb3000 (docking station)?

  I got a HP Pavilion dv9000 for about 7 years and use it at home with the HP xb3000 expansion base that has USB connections as well as the Altec Lansing speakers like the laptop.  A connector on the base of extension plugs into the connector on the expansion of the Port 3 on the Pavilion dv9000 and it has always worked very well. It allows additional hard disks must be installed in the base of the expansion, but I have not used this option.

  I recently bought a HP Envy 17 quad t laptop with Beats Audio speakers.  It doesn't have a connector of the expansion Port 3, so I was wondering if there is any type of connector/adapter allowing the HP xb3000 expansion base be connected to and used with the HP Envy 17 T.  Any suggestion would be appreciated.  Thank you and have a great day!

  Hello

  Envy has no expansion port so the base is useless in your case. A few other products that use the USB port would be useful.

  Kind regards

  PS a compatible list updated January 21, 2014:

  http://en.Wikipedia.org/wiki/HP_xb3000

• HP Envy 17-3070nr video driver for Windows 8? 3000hd Intel / video driver ATI 6790

  Is here and there at - it a bios update coming to allow fixed graphics mode?

  See my post

  http://h30434.www3.HP.com/T5/notebook-display-and-video-e-g-Windows-8/HP-envy-17-3070NR-and-steps-I-took-to-get-ATI-card-to-work/m-p/2280775#M60502

  Good luck, it worked for me...

• I just installed a SSHD and cloned my old SATA HDD through him. My CC 2015 apps work okay but the creative cloud app does not start. The circle of rotation right guard go. What should I do?

  I just installed a SSHD and cloned my old SATA HDD through him. My CC 2015 (Photoshop and Lightroom) apps work okay but creative application cloud does not start. The circle of rotation right guard go. What should I do?

  Sorry to have troubled you. I rebooted and everything works now.

• I want to Exchange my hard drive of my iMac for one SSD. Existing hard drive will be cloned on the SSD. I have CS 3 Design Standard installed. What I have to deactivate/reactivate CS3 or will keep the data license/activation?

  Oh, I of course put the whole issue in the reference line.

  I'll repeat it here.

  I want to Exchange my hard drive of my iMac for one SSD. The existing hard drive will be cloned on the SSD. I have CS 3 Design Standard installed. What I have to deactivate/reactivate CS3 or will keep the data license/activation?

  Thanks, Thomas

  Transfer facilities of Adobe does not normally operate.  You must reinstall using installation files.  At a minimum you must disable, but you may find that you need to uninstall and reinstall.

• HP ENVY Phoenix 860-008na: removal of the bracket for graphics card?

  system specifications are,

  Intel Core i7 6700 Skylake @3. 4 Ghz to 4 Ghz

  16 GB DDR4 RAM

  2 TB HDD & 128 GB SSD storage

  GTX980Ti 6 GB GDDR5 NVIDIA

  Windows 10

  just wondering if its ok to remove the mounting bracket that is attached to the graphics card to get the best air circulation

  is it right in place for shipping?

  Thank you

  Hi there @junior19805,

  Welcome to the Forums of HP Support!  I understand that you ask a withdrawal of the graphics card of mounting brackets for better circulation of air.  I'm happy to help you with this.

  There are a few problems with this. First support firmly maintains the card in place in its decision to maintain a good connection and prevent the flow of the socket. Second, although it may seem intuitive abduction, counter to the back plate of the computer can actually hinder the cooling system, as the positioning of various fans and admission of eaves, are often designed to channel air flow, so it travels on the components that most need cooling.

  All that being said, you can always try it and see if there is an improvement in your case, but the possibility of a graphic intermittent connection is going to be a matter of concern

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.