HP LaserJet M1319fMFP Fax receive problem

Similar Questions

• Unwanted fax confirmation pages for faxes received on HP LaserJet 1536dnf MFP

  I would like to disable the confirmation pages for faxes received on my HP LaserJet 1536dnf MFP but keep the pages of confirmation for faxes sent. How can I do this?

  It is not too difficult.  Press Fax Menu button.  Tap the right arrow until that fax reports is on display (should be the first thing that pops up), then tap OK.  Press the right arrow until Fax of Confirmation is displayed (again, it should be the first thing that pops up) and press OK.  Press the right arrow until you see Send Fax only and press OK.  Now you should be set to get reports of confirmation only when sending.  Hope that helps.

• All-in-one Officejet J6400 Fax receive not always or not at all

  OfficeJet J6400, Vista.  Connected to the laptop via cable and wireless.  It is connected to the same phone number line, with the answering machine.  Settings seem correct and even when I had previous HP printer.  4 rings on the answering machine pickup and 6 rings for fax receive.  The fax does not receive.  Even if auto answer is on.  I am able to fax, manually. (have not tried otherwise)

  I have to figure out how to keep the auto answer on vs switch mode 'sleep' (of another post).  But sometimes it is not in Standby Mode and AutoA is off.   Regardless, machine does not seem to take faxes.  BUT, when you do the test with HPFaxme, it doesn't work. !

  And, when you use the HP Solution Center, all settings are made, and sometimes their fax Test does not work.

  Another question... in Fax configuration, which is PC modem in this question in quotes?  It's same as router? -"Are you using a PC modem (to access online services) on the same phone line as the device HP?   Answer is Yes or no.  Which is mine?

  I don't have DSL, and fax is on the same phone line. I have a DSL filter connected to the wire, of course.  Another wire goes from phone line in the wall (there is a separator) to the router.  This configuration refers to highest question?

  Is the best connection wireless or cable (printer for laptop)?

  Thank you!

  I'm back earlier than expected.  I never ran any patches of the HP link because another action (s) would have helped (which is recommended for another problem I had).

  So-

  I had the printer connected to the laptop via a USB connection and network.  (wire cable between the printer and the laptop and wireless through the printer setup)   Due to many problems to make the light stays on 'Auto response' (I posted on this separately in the recent past), I have the settings Fax arranged in a strange way to make this work.  So I didn't want to change these settings, what would be the recommended link for me to do.  For the problem of the 'auto response', I ended up connecting computer to the printer via the cable. And that probably contributed to this problem.

  I kept the two connections since and chose USB (OfficejetJ6480 copy1) wire as my setting of the printer preference in the settings box of the printer in Control Panel.  I think that even when I did the Wifeless-network connection preferably in the settings area of the printer in the Control Panel, the receiving fax machine or tests do not seem to work (even if it was some time ago and not tried recently).

  I think the duplicate connections was things confused.  The fax Test seemed to spend during a test of the printer settings button.  But he would not pass when the test has been made Fax Tools in the Solutions Center on computer. (And this I tested it today.)

  SO, I deleted the wireless network connection and the "device" (officejetJ6480) in the settings of the printer in the control panel.  I simply removed it.  I have left the "copy1 OfficejetJ6480" intact and continue the preference for the 'peripheral '.

  I have rebooted computer and run Fax Test of the printer and printer Solutions Center on computer configuration tool.  And they both passed Test.  Go figure.

  And also, the test of HPFaxMe works very well.    Thus, 3 tests have passed. !

  I hope this will be useful for someone even if it is confusion.

  But I'm sure that one of the hotfixes in the MissTeri link should help too.

  Thanks MissTeri!

• I can see only the last fax received in my PC and not all of them using an Officejet Pro 8600 Plus

  I create a file in my office where received faxes can be saved. Indeed, I can see the fax received, but if I get one more, it replaces the previous one. So, I see only the last received fax. How do I see all of them and does not replace another?

  The problem was that I didn't set the time on the machine of the printer.   I just put the date and time and the problem solved. I get faxes pdf correctly.  Be it, thanks for the help!

• HP j4580 fax receive

  I set up my HP to store faxes received on a folder on my PC. How can I configure this machine DO NOT print all incoming faxes at reception.i am on win-7/32 bit

  Thank you

  looks like the answer to that is in front of my eys! Just read the printer digital Panel... Yay for me...

• Is it possible to automatically send all faxes received on a Windows 7 computer to a specific E-mail address?

  Original title: transmission of faxes received by e-mail

  Hello

  Is it possible to automatically send all faxes received on a Windows 7 computer to a specific E-mail address?

  Thanks in advance.

  LM

  Hello

  I would like the links and check if that helps.

  Configure your computer to send and receive faxes

  Receive a fax with Windows Fax and Scan

  Hope this information helps. If you have any other questions about Windows, please let us know.

  Thank you.

• Problem HP LaserJet CM1415fnw Fax

  Have a computer running windows 7.  Have a MFP HP LaserJet Pro Cm1415fnw color that gives me problems with the installation.  This work until an update progress for blue tooth tried to install and could not, since then, no fax.  I uninstalled the time multipul of HP software and then reloaded.  I can get the analysis and the printer to work but it wont let me load the fax driver.  The error I got is (cannot add telecopie1 87 HP print driver code).  Also the primer Toolbox but show no items such as ink levels, ect.  Someone at - it suggestions?

  Hi ArizonaJohn,

  Follow the steps below

  1. remove the printer using Add/Remove programs in the control panel

  2. run the Accessories\ System Tools Disk Cleanup

  3. restart the computer

  4. download and install the software from the link below.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=kJ-85658-3&cc=US&DLC=en&LC=en&os=4063&Product=4089468&sw_lang=

  I would like to know what is happening?

• LaserJet MFP127fn fax sending question

  I'm having a problem with several units of Laserjet MFP127fn that comes to buy. When I go on send a fax and start typing the fax in the unit number, he's trying to connect before, I finished dialing the number. Other times he said cancelled fax but it would try to send. Then there's moments where it just goes back to the menu that says "load the document" that I type the fax number in.

  I know wait until I typed the number of fax in then pushed ok before he dialed the number of the machine.

  Is there any solution for this? I tried upgrading the firmware with no luck. If there is no solution for this I plan to return all 70 units that come to buy.

  Hi marquism76,

  Sorry for the late reply. I was check in this issue. I'll try my best to get this resolved for you.

  I have provided a document through the steps to see if this will solve the problem.

  Cannot send or receive faxes.

  Run the fax test. What were the results?

  Disable error correction.

  Set the speed to slow.

  Also to go into the configuration, the menu of configuration of fax, private receive and turn off please.

  Just to clarify, you came and then fax number by pressing the button start Fax?

  Send a fax .

  If the problem persists, could you possibly pass the device to one of the places where you are not the issue to dismiss any connection problem?

  Please let me know how make you out.

  Thank you.

• HP Laserjet 3055: Fax for HP Laserjet 3055

  Dear Sir.

  I want to ask questions about faxing.

  is it possible that when someone fax to me, I can save it in a folder or a file?

  because I have a problem with roll.

  It can suck 2 or more documents at the same time.

  and when he got paper jam.

  can I save the fax file in a folder?

  Thank you

  @rosen_putra86

  Your printer can do "all kinds" of the fax functions.

  The User Guide is a good resource to learn how to use the Fax options, including the section:

  Send and receive faxes using a computer > Chapter 11, Page 210

  The computer that will receive faxes must be available at any time (not asleep or closed).

  Printer:

  HP LaserJet 3055 all-in-One printer range

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

   

  My answer-click accept as Solution to help others find answers.

• HP640 received through telephone fax receive code

  What mode of response/receipt the HP640 must be set on for the ' telephone receiver an extention "code manual fax machine works. Made for SUCH and not joy. Other modes seem to respond automatically. Manual does not cover.

  Hi gusjen,

  To use another phone to activate the fax, it would need to be defined to receive faxes manually. Once you pick up the phone and determine whether an incoming fax that is when you enter the code for the fax to take over the line. If the manual does not work, then you have a hardware problem with the machine. You call our technical support at the 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://www.HP.com/cgi-bin/hpsupport/index.pl

• LaserJet MFP M177fw Pro: Problem of scanning color multifunction M177fw

  Hello

  I'm using a MFP HP LaserJet Pro M177fw in my office for awhile. I have no problem with printing and faxing. But I can't do color scans good I can do scans in grayscale at 200 DPI. I get the following error when I try to make a color scan.

  

  I use Windows 10.

  Any suggestions?

  Best regards

  YK

  @Silahtaraga,

  Thanks for the information. I would like you to go ahead and follow the steps below:

  Try disabling your firewall and running the installation to see if it allows you to install, if this does not work try a clean boot and run the HP printer install wizard for Windows , it was created to help Windows 7, Windows 8, Windows 8.1 and 10 users to download and install the latest and most appropriate HP software solution for their HP printer.

  Additionally, make sure that the Firmware is up to date, see here: get printer updates

  If you still run into installation errors, continue here: after Windows 10 Upgrade, printer problems

  Let me know the results. If this resolves the problem please let others know to mark this message as "accept as Solution".  To simply say thank you, click the "Thumbs up" below!   If you need more assistance let me know and I will gladly do everything I can to help.

• fax memory problem

  We have a MFP HP LaserJet Pro M521dn

  We had several problems with incoming faxes.

  We see 'Problem memory' to appear on the screen of the machine and the error code 232 on the error fax report.

  I set the fax speed, and that did not help.

  Any suggestions?  I don't see a way to clean the memory on the Board upward.

  I am new to using this machine; am I missing something?

  \Thank you!

  Hello

  If I understand correctly, you get a memory full message fax.

  Kindly click on the following link to fix the problem.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/troubleshootDisplay/?sp4ts.oid=5281272&spf_p.tpst=psiContentDisplay&spf_p.prp_psiContentDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c03491494-14%257CdocLocale%253Den_US&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Although I am an employee of HP.

  Please click on the 'Bravo Thumbs Up' at the bottom right of this post to say 'Thank you' for helping! or click on "Accept as Solution" If you feel my post solved your problem, it will help others find the solution.

• HP OfficeJet Pro 6830 all-in O: printer 6830 fax receive not when auto answer is disabled

  I have a phone that has an included answering machine. My connections with the phone jack, phone and printer are all properly connected and voice calls and faxes are basically works well.  My problem is when I have the off Auto answer and I receive a call, the answering machine get it if they want to leave a message, but if they press send at the end of a FAX, it won't in fax mode.  I have to be present and manual press FAX on my end.  If I put it on Auto answer, then when the phone rings and he answers it automatically in FAX mode, regardless if it is a fax or voice call. The rings before answer is 4, but I also tried with 2.

  How can I configure it so that I can do both... which means that when a call comes in, it can get picked up by the answering machine if they want to leave a message or if they want to send a FAX, press they SEND to their end and it passes the FAX on my end.  I used to have like that with my other all in one printer so I know its possible... at least with another HP model.   Thank you in advance.

  Try all the 'rings to answer' on the fax machine to 6. You must set the 'rings to answer' on the bigger than the 'rings to answer' fax on the answering machine the answering machine have a chance to pick first, and if it is a fax tone, the fax is then pick up.

• C410 Photosmart all-in-one with fax series problem

  My Photosmart Premium FAX e-ALL-IN-One c410 series does not receive faxes.  It is on the automatic response and the phone rings (with a fax signal), but it does not pick up. Can you help me? I was able to send a fax the other day, but before that was a little more difficult.  I ran the test fax several times and he said: it is spent.

  Hello

  Here is a document that will help you check your fax settings and solve your problem. Since you have already performed the fax test, you can go directly to the #2 Solution.

  http://support.HP.com/us-en/document/c01632148

  Good luck!!

• Sey uphp 3015 laserjet to fax

  How to configure my hp 3015 laserjet to send faxes without disks?  I received as a gift a few years ago and I would now use to fax. It's a 60.5.72.21

  You don't need a disk to send faxes. The only thing you will need is a phone line running to the rear of the machine fax entering directly into the wall outlet. Connect the phone to EXT 2 of the printer.