HP Officejet Pro 8600: Printing vertical lines when you use doc auto power

Similar Questions

• HP Officejet Pro 8600 Plus: vertical line when scanning

  I get a vertical line when I scan using the document feeder.  I do not understand when scanning the glass plate. I need assistance to access the mirror slider.  I raised the lid for the loading of documents, but I couldn't find out how to get under the rollers to clean the mirror. Thank you

  The document here can help solve the black lines to scan using the ADF on your HP Officejet Pro 8600 Plus.  From my experience this is almost always caused by a specification on the thin glass on the side left which is used for scanning using the ADF.  Cleaning of this area as described in the above document should solve the problem.  If the initial cleanup does not resolve the problem, it can help to shine a bright flashlight almost parallel to the glass.  For a line on the left side of the printed page, the place will be toward the front of the printer, if the line is on the right side of the document, it must correspond to a specification to the rear of the printer.

  Figure: Clean the ADF scanner glass Strip

• HP Officejet Pro 8600: Thin vertical lines when printing photos

  The printer referenced did a fabulous job to print photographs.  In this case, the printer is fairly recent and has recently recently consumed the original cartridges when it was decided to try to use it for photo printing.  Therefore, the fabulous results were extracted relatively new cartridges and consisted of at least a dozen photo printing in various sizes.  Then all of a sudden these thin vertical straight lines began to appear in print.  They are equidistant on the full image.  That they appear in the printed image.  When using paper letter (8.5 x 11) to print an image cropped at 8 x 10 with landscape orientation spacing is about 1 1/8 (one and one-eighth) inches or 8 evenly spaced vertical lines.  Somewhat like the photo was divided into 8 columns.

  According to the printer built in ink gauge, that the cartridges are now just a little more than half full.

  These lines are narrow enough so that they are not very visible when printing on normal paper (copy).  They would probably be imperceptible on many kinds of printed documents.  However, they become quite noticeable and reprehensible when using good quality (in this case HP) photo paper to print photos.

  Absence of a printer resolution is not good for photo printing.

  In addition to the troubleshooting suggests that the problem is not due to the printer, but rather to the software used to perform the printing. It was not immediately obvious that I printed only photos using Picasa and it worked fine and then all of a sudden the problem developed. However, I have now tried to print the same photos with other software and there is no problem for the steps.

  The Picasa forum also has many messages wanting to be the same or a similar problem to what I have experienced. Unfortunately, there doesn't seem to be an explanation for a repeatable cause, nor a specific solution. Some hacking autour with the settings and options seems to be in order. If it does not then print with other software may be necessary.

• OfficeJet pro 8600 black vertical lines of print when copying

  I got a new of OfficeJet Pro 8600 a couple of weeks, and it worked fine until today, when I tried to copy something. I can always print from my pc and scan without problem, but when I try to copy a document (if I load it into the tray or put it on the scanner) the page comes out covered with black vertical lines of different sizes. It seems that this isn't the ink or the scanner since I can print from my pc and analysis very well.

  Help, please!

  This unit is plugged into a wall outlet directly? If this isn't the case, then try to connect the unit to a wall outlet directly.

  The 8600 Officejet Pro has built in the surge protector and double this feature may cause some problems.

  Also, try to reset the printer hard:
  * Unplug the unit while the printer is on
  Disconnect the other end of the power cable from the wall socket direct
  * Wait 30 seconds
  * Plug the unit to the top

  Let me know if it helps.

• HP Officejet Pro 8600 N911a - vertical line using ADF

  I have a problem with a black vertical line on the right side of scans/copies when I use the ADF. There is no problem if I use the Board.

  There are a number of similar messages here and I tried all the solutions I could find including:

  Cleaining each wheel and sproket I can find (several times)

  Clean the glass (several times)

  Unplug the printer on, several minutes of waiting and reconnection (several times)

  Unplug the unit as described above and by using a different wall outlet with any other equipment on the line

  The pilot of uninstalling and reinstalling

  Update the firmware to the lates version (March 21, 2013)

  None of this works and I get the result below.  The one you have any other ideas?

  .

  When you clean the glass, you did clean the small strip of glass on the left and the thin white on the top lid?  These are the sections of the scanner glass used by the ADF.

  If so, then I have some information for a factory reset in the Officejet Pro 8600.  I will send this information to you in a private message.  Please read Bob_Headrick wire on the printer reset, found here, before you perform these steps.

• Photo printing, vertical lines when you print multiple images on a page

  I went from iPhoto to Photos. Now I'm having a problem printing (HP Photosmart Premium 309 c) pages with many photos for my annual calendar. Often the picture on the right will have vertical lines. I use PS 14 items.  I did this for years and I am sure that the problem is related to Photos and the fact that my photos are now in the cloud and not on my Mac.

  I recently removed my hard drive iPhoto library - because I don't have enough space on my Air.

  Hello

  Thank you for using communities of Apple Support.

  I understand that whenever you print photos of the Photos on your Mac app, the lines appear in the printed image resulting.  The following steps will help isolate the matter with Photos or the printer itself.  To start, please print one of the photographs from the Photos app to confirm a specific photo translates into lines on the printed copy.  After seeing the photo, please export the original photo of the Photos app on your desktop, open the photo in the preview and then print this photo.

  Export pictures in their original format

  1. Select the photos you want to export.

  2. Choose file > export > export Original unmodified.

  3. Click Export.

  4. Choose where to save the exported photo files and then click Export the originals.

  Please report back with the results of these steps so that we can help you.

  Take care.

• OfficeJet Pro 8600 Premium: Vertical line by page

  When making copies or receive a fax it is a black vertical line that runs through the entire page, just off center.  When I print from the computer it is not there.  How can I get rid of this?

  Hello

  Do you think it is happen when a fax is received or can it happen on a fax sent? (using the same mechanism as when copying).

  Try the following three Solution below and check if this can help you:

  http://support.HP.com/us-en/document/c02881567/

  Shlomi

• HP Officejet Pro 8600: Printer list offline when it is not.

  Printer list offline when it is not.  I connect wireless to my network that everything is connected properly; can scan etc, but when I try to print it says printer offline.

  I didn't turn Windows 10 for much question of withour months, now today go... tried everything!

  Hello

  Thanks for the comments.

  You can try the following:

  Creating a TCP IP port

  1. print a Configuration Page to get the printer IPv4 address (you can also tap on the icon wireless on the front panel of your printer to obtain the IP address)
  2. on your PC, go to the Panel control, devices and printers, right-click the printer and on the left, click printer properties, select the Ports tab.
  3. click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.
  4. Enter the IP address of the printer.

  Note that you can ALWAYS go back to the original port the HP software installed by selecting the HP port on the Ports tab (in the properties of the printer)

  Hope that helps!

• OfficeJet pro 8600 print a single vertical black line when using the charger

  OfficeJet pro 8600 print a single vertical black line when using the charger

  Hi @realestatejeann,

  I see that you have found one black vertical line when using the ADF. With a few steps, we should be able to solve this problem.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Here is a document for the cleaning of the glass Strip and the underside of the scanner cover.

  Vertical stripes, lines or streaks on Copies, faxes or scans.

  If you need help, let me know.

  Good day!
  Thank you.

• OfficeJet Pro 8600 wants fax info when asked to print

  OfficeJet Pro 8600 prints test page ok, but do not print anything My Documents or a receipt from a purchase online.  A screen will appear with corner 'Send fax' at the top left, boxes of 'to', 'add a cover page', 'Add scan' and 'settings '.  There is no error message or the number.  Tried to remove and reinstall the printer drivers and.  Worked fine for 2 months, then started it.  It is not connected to a phone line and has never been used for faxing.  It is connected to the wireless computer network.  Tried to connect to the network with cord - also not able to print.  Any help appreciated.

  Hello

  I guess that the fax printer is set as default, download and execute HP Print and Scan the link below Dr utility.

  www.HP.com/go/Tools

• OfficeJet Pro 8600: Printer offline and HP Support for Windows 10 don't come upward

  I'm trying to scan pictures to my computer.  Have upgraded to windows 10. My printer is connected wifi.  I bring the printer in Control Panel, set up my printer and it says printer is offline.  Indications are no good they do not appear to be implemented for users windows 10. When I try to go to the hp support for windows 10, I have just a white screen.  I am very frustrated.  I can print to the printer, but he won't let me not scan to the computer, and that's what I need.

  Hi @Procats,

  Welcome to the HP Forums!

  I understand that you cannot scan on Windows 10, with your HP Officejet Pro 8600 printer. I'm happy to discuss this issue scan for you!

  Please, try the following steps:

  Check the connection of the printer on the network and troubleshoot any problems with the printer, router, installation or connection.

• OfficeJet pro 8600 printer-how to make this program work and installation?

  I have problems printing. I wonder how to ste it to the top and do work.

  Moved from feedback

  Original title; printer Officejet pro 8600

  Hi David,

  1. what operating system is installed?

  2. what security software is installed?

  You can go through the printer manual to know how to set up the printer and make it work.

  You can also refer to these items and check if that helps.

  http://h30434.www3.HP.com/T5/printer-all-in-one-install-setup-e-g-Windows-8/How-do-I-install-printer-software-on-HP-OfficeJet-Pro-8600/TD-p/1123283

  http://h30434.www3.HP.com/T5/forums/SearchPage/tab/message?filter=labels%2Clocation&location=Forum-Board%3AInstall&q=OfficeJet+Pro+8600+printer

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• HP Officejet Pro 8600: Printer does not print in color

  I just got the color cartridges refilled at Costco. Now, my printer does not print in color.  I printed out a diagnosis and cartridges are showing that they are full.  The actual color of magenta is a deep rose, so I know that some of the magenta is crossing. Cyan (blue) and yellow printed black on diagnostic tests.  I know that Costco filled cartridges with the appropriate color because I can see the color on/in the cartridge.  Suggestions on what to try? I bought the printer on January 27, 2013.

  Hi @monitons,

  Welcome to the Forums of HP Support!

  I see that your HP Officejet Pro 8600 printer will print correctly since fill you the ink cartridges. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution" if I helped successfully will solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand the frustration you are experiencing.  It seems that there is a problem with the print head or ink cartridges.

  To determine the cause, I would like to use this document:

  • Fixing poor print quality

  If the problem persists, I suggest you try a new complete set of ink cartridges.

  How many times have you filled out the ink in these cartridges?

  TIP: Reloaded cartridges can stop functioning over time, if the nozzle one chip or ink is damaged.

  Note: HP recommends you to use genuine HP cartridges. HP does not guarantee the quality or reliability of cartridges HP cartridges refilled HP.

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.
  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair.
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• OfficeJet Pro 8600: Officejet Pro 8600 leaves black lines on docs scanned when using the document feeder

  This is the second HP Officejet Pro 8600 I had - one was replaced by HP, after that the same issue arose.  I tried to clean the entire unit, but we still get a thin black line running vertically down the page.  This line is divided into sections of 1 "and 2.5" in length.  Sometimes I get the fine line and then almost a shadow line that is parallel.

  Any suggestions would be very appreciated I have scan documents to PDF format and it's hassle to put everyone on the flat for scanning.  I use the charger of the doc on a daily basis and wonder if this could have something to do with the lines.

  Thanks for any help.

  The question is a spec on thin (~ 1 "wide) glass to the left of the main bed scanner.  Clean this area as described in this document.  It can be difficult to see the affected area, a bright flashlight which is held at an angle to the glass can help find the place.  Even a very small spec on the glass can cause a black line when using the ADF.

  

• HP Officejet Pro 8600 missing some bullets when printing

  HP Officejet Pro 8600 for young or skips lines especially bullets when printing.  This isn't a problem of ink.

  The documents that are printed look fine except some lines especially bullets Miss.  Always the same lines/bullets Miss.

  I tried printing from Win XP, 7 and 8 - all have the same problem and the same senses are missing.  The print view looks very good.

  This happens when you print items from the internet.  I use Chrome on all computers.

  I have the latest software, drivers and firmware.

  Copy the information in Word 2007 prints without problem I printed documents pasted unchanged IE. no change, the format or the police.

  Print a PDF file has no problem.

  I've had the printer for 5 months.  The computers are the same during this period.

  I only noticed this problem in the last few weeks - after print a recipe and trying to follow, I noticed lack of bullets a receipt detailed ingredients.

  I have unplugged the printer and plugged back in - the problem persists.

  Please help with this frustrating problem.

  OK fine and yes I think it's a matter of Google Chrome as well. Let me know your results when you get a chance.

  Enjoy the updates!