limited WRT160N wireless connectivity

Similar Questions

• WRT160N Wireless connectivity limited or not

  Hello. I have a WRT160N router set up on a XP computer with DSL service. Have a Realtek to connect to the network local and Marvell Yukon for the wireless, which presents itself as the connection to the local network 5 in network connections. The Realtek works well but the Marvell Yukon shows "limited or no connectivity" and cannot renew the IP address. Tried to manually key in one IP address, but it runs very slowly (584 sent, received 4) and Network Magic also does not detect connections wireless at all.

  Y does it have wireless connection can get a speed much better with the IP address or are there other parameters that need to be adjusted for this? Is it possible to have two connections working or should be just one or the other?

  Hello. Yes, the OS is Win XP Pro. For some reason, the wireless network connection properties has a second tab for wireless network. The second tab there arises as advanced.

  What finally solved it for me has been assigned an ip address that has worked. Both cards work fine at the same time without any conflict so far. Only using one of them at this point, but it is good to know that the other is works when necessary.

  Thanks for your help, if. Really appreciate it.

• WRT160N wireless connection instability.

  It's long, so I'll try to keep it short.

  Research, I see there is a problem with the current firmware of hardware v2, but that doesn't apply here.  I am hardware with Firmware 1.02.2 v1.  I see also several other posts with connection problems to the outside world, and troubleshooting that surrounds the cable modem and the DHCP settings.  I don't think that's the case here.

  I inherited the router of parents who felt it was slow and bought a newer linksys N router.  I put that to them, Wednesday night, and it runs perfectly.  I brought the 160N House and hooked up to my network.  Since she still had their place connection settings, my laptop connected immediately with the saved settings.

  Since it by plugging, the performance is terrible.  The traffic seems to move in short bursts but can not stand.  See the below screen Cap.

  When copying on LAN network: http://farm3.static.flickr.com/2638/4138717058_449c7ac092_o.png

  The scale is actually 0-5% in this one, so I'll sometimes get decent speed, but not gusting more than 1 second.  The machine on the other side is physically connected to the router by ethernet.  The connection for computers physically connected is great.

  Does anyone have an idea?

  Try to adjust the settings of your wireless router...

  Open page setup on the Wireless tab, change the SSID in a unique name, change the Standard - 20 MHz Radio band and change the Standard channel at 11-2, 462 GHz... Under wireless settings advanced
  Change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings... Power of the network of cycle and try...

• Satellite M40-313 (PSM44E) limited or no connectivity LAN wireless

  I have always been connected to our home wireless network and the connection within the House is still ok, but after the restoration of my factory settings I came to only get limited or no connectivity.
  After a problem with my DCOM Server process Launcher I find completely my laptop, not I can recognoise our network but cannot use internet or access files, after a friend recommended I update my Atheros wireless driver I did, but it has not changed anything.

  Is that what I can do to fix this problem without having to pay someone or buy a new laptop?

  Thanks much for any help.

  Karen

  Have you tried to turn turn off the firewall and other security software?

  Also try to use a static IP instead of DHCP and enable file sharing.

• Connection has limited or no connectivity / wireless network not detected

  So two problems here

  1. I used to transfer studies ultrasound scanner for my HP Mini 110 - 1025DX PC. For this I used to establish a connection to the system, where the name of the internet connection was same as in HP mini and address IP was also the same, except for the last digit (i, e XXXX:XXXX:XXXX:XXX1 vs XXXX:XXXX:XXXX:XXX2). Firewall Windows should also be disabled for mini HP transfer studies. I repeated these steps after reinstalling windows but icon in the mini bar of task HP says limited connectivity or none and so I can't transfer studies. How can I solve this problem.
  2-HP mini also has Wi - Fi. Is there a way can mini HP tell me networks wireless in my range so that I can choose mine, key network related so that my wireless internet access also starts to work.  I'll be very grateful for any help.

  You want to connect your mini to the ultrasound with a cable machine and the mini to your wireless router to access the Internet.

  The next part of the instructions

  Right-click on the icon for your wireless adapter and select Properties

  should have been

  Right-click on the icon for your Ethernet card, and select Properties

  in order to properly configure your Ethernet (wired) connection to the ultrasound machine.  Sorry for the mistake.

  And, of course, if the mini is connected to the machine to ultrasound with the Ethernet cable, it is not to connect to the Internet via cable.

  Maybe you need to explain more clearly what the situation is.

  • The ultrasound using a cable or a wireless connection?
  • You want to be able to plug a cable between the mini and the ultrasound machine and when you have completed data transfer, connect a cable between the mini and your router?
  • When you "used to transfer studies ultrasound scanner to your HP mini" could you unplug the cable from the ultrasound machine and connect it to your router and connect to the Internet?

• I unchecked the "notify me when this connection is limited or no connectivity" for my windows wireless and LAN connections, but the icons still appear in sys tray when it is disconnected.

  Hello

  I use my Intel client to manage my wireless network connection in Windows XP Pro SP3. (I need to use the Intel client because it supports protocols wireless not supported by the Windows client).

  I would like to remove the icon from the system tray/notification area Windows wireless network connection and cannot find a way to do it.

  I opened the network connections, right click and choose 'properties' and in the general tab at the bottom there are two check boxes "Show icon in notification area when connected" and "notify me when this connection is limited or not connectivity ' which I disabled (I did it for my local network also), but the icons still appear in the status bar when it is disconnected.

  
  Any suggestions?

  Thank you

  Bob

  I found a registry change that removes the icon in the systray.  One needs only to remove these keys (save the first):

  [HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E}]

  [\DefaultIcon HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E}]

  [HKEY_CLASSES_ROOT\CLSID\ {7007ACCF-3202-11D1-AAD2-00805FC1270E} \InProcServer32]

• Connect WRT160N wireless to the BEFSR41 wired

  Hello-

  I use the router BEFSR41 which is connected to my comcast modem and all PC, printer, computers cell phones work perfectly when you use additional ports.

  I want to know if its possible to add a wireless router, WRT160N, across to the top, so I can move and then another room with the laptop.

  I play internet games on my desk and do not want to move to the wireless, but use the laptop to other purposes of internet and sometimes need to use it in another room.

  I have read the posts here and it seems possible, I want to just make sure I get the correct connections. I have also read the messages that State no, do not.

  Are there easy instructions?

  Thanks for any help,

  CAT

  I think that from the beginning that my problem was trying to connect wireless to my desktop PC... and after an hour or so trying to reconfigure the son discovered is not wireless because at the end of the year I had to buy a new network card and wasn't capable wireless.

  I thought that since my office was the main link everything had to go through to the 'House' to work wireless connection.

  So the first time that I have not found a link on the desktop, we wire the PLACE directly to the computer laptop and charge the WRT software on the laptop. The problem, he had us were always wired to the router BE and this is the page of the Linksys who returned to the top. We try to change the LAN IP address and turned off DHCP, but of course when I am connected to the internet on the desktop, it was not to find the router.

  Of course during all this time, I was looking at this site and then went on the Comcast site, it just clicked and after several configurations more lead changes and trying to think about what I wanted to accomplish exactly, and how it "should" work... just went ahead as it was already set up and connected wireless to the BE and he was there.

  I also remember that when you reset the modem and the router... it takes 'time '. As at least 5 min, what seemed like 15 minutes at the same time, I tried all of this. My frustration level has not helped knowing that it "can" be done if I just follow the signs.

  So overall, my error when trying to set up my office as the main connection for the wireless and don't listen to not when my granddaughter told me that she 'had' upcoming wireless on the laptop.

  Thanks for your help and great advice. We have the wireless connected and followed your instructions on securing the router with the network name, encryption WPA2 and AES... and hope never to lose the piece of paper its written on.

• Wireless connection is always set to "limited connectivity" on Windows 8

  My wired connection works fine, but when I try to connect wirelessly, my connection is limited. This problem is not moved when I got to my laptop. I have tried to start in safe mode, install the latest drivers for my wireless card and also get into the command line "netsh". Any help would be appreciated, thanks.

  Please try the below given the stage he worked for me for connection problem in Windows 8 Pro limited. I tried to connect via Nokia Lumia 720:

  1. Right click on your WIRELESS connection and click view connection properties.
  2. Click the Security tab.
  3. Click on Advanced settings which opens the 802.11 settings.
  4. Check compliance to enable FIPS Federal Information Processing Standards () for this network.
  5. Click the OK button.
  6. Reconnect your computer by WIFI and enjoy the internet.

  Please update if it works for you.

• Very limited wireless connection

  I have a HP Pavilion dv7 - 3153ca with a 64-bit windows system 7 and I'm only able to get a wireless connection when the laptop is very close to the modem. Once the laptop is moved, for example, to another floor of the House, the connection is lost and cannot be re established until I have the back next to the modem. He has no problem with the wired connection. This has happened while he was trying to pass my McAfee security provider, although I don't think this is the problem that my other laptop (a Dell) converted without this problem. The other laptop continues to maintain its connection Wireless throughout the House, so the router and the modem is not the issue. I downloaded and re-installed the adapter without modification. I have scanned the laptop and nothing is reported in the mess. Are there any ideas as to why the wireless connection works only when the laptop remains close to the modem? Thank you.

  It seems I may not have been very clear in my previous post.  I wanted to suggest was to reverse the connection of the antenna.  As mentioned in the thread I linked, the connections might have been reversed from what they should be from the factory.  If this is the case, then connect the antennas in a factory setting would not solve the problem.

  Have you tried to reverse the antennas?  If they are in the deformities, then this would fix it.  If they are in the right position, then the worst you would have (only in the deformities) would drop signal strength.

• WRT54G - wireless connection limits?

  Yes, I have a WRT54G V6 router, and I wonder how many wireless connections it supports?  Because, I have a wired connection, and whenever I try to connect more than 4 wireless devices, a device will be get launched.

  So is there a way to open more wireless connections or suggestions?

  Thank you.

  On the computers of all Vista and Win 7 disable IPv6 in LAN properties for both wireless and Wired Adapters.  Disable UPnP in router.  Restart the computer and try again to connect.

• PC HP Pavilion 15 15-p001tx: control wifi wireless connectivity issues

  Hello
  Member of the Community/Forum
  
  Model name - laptop Hp Pavilion 15 (15-p001TX)
  Questions - Brodcomm 802.11n wireless adapter not Worming.
  
  Problems-
  I was faced with the same problem for 4 days and I tried all possible means to resolve out, but nothing works.
  
  Problems are the following:-

  1) Wifi stopped working 15 minutes to restart the computer and the wifi icon is automatically limited, and then it automatically become the LAN (small PC icon) and after this phone get hanged every time.
  
  to re work I need for wtich forcefully from the power button.
  
  2) I followed all the tips and tricks to solve the problem and even take a Hp support helps solve this problem of wifi. but nothing works... no one has helped me on this problem.
  
  Here are the ways I've tried.
  
  1. that tick managent of power, I have UN ticked (from PROPERTIES)
  
  2. using the CMD, I reset
  
  3. I DID cofig automatic Wlan disable (and put it on startup)
  
  4. update the drivers to the latest Version.
  
  5 install the latest drivers from the HP website brodcomm or even other Web sites.
  
  No the above to help me out.
  
  3) all wired network work great, but when I swtich to wifi, it will automatically limited and then diirectly hang the entire notebook.
  
  Please please suggest the Suggestion and the ways out sorting valueable.
  
  He's really frustrated now, I do not understand what are the ways to my wifi on working condition.
  
  Thank you
  
  Kind regards

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Aditya Rai

  Aditya Rai

  Hello @adityarai82,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I read your post about the WiFi problem and wanted to help you!  I understand that you have tried the troubleshooting steps a lot already, without success.

  Try to review these steps, offered by community member @Great-Christine-Tree:

  First of all, we have a step by step guide to guide you through the process of diagnosis here:
  Troubleshooting your wireless network and Internet access

  A second option is to try the following steps:
  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.
  
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.
  
  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.
  
  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  Source: fixes Common for wireless connectivity problems.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• U940 PSU6VA satellite - wireless connectivity problems

  _ * My specifications: * _
  * Model: * Toshiba Ultrabook (Satellite PSU6VA - 00S 002 U940)
  * Operating system: * Windows 8.1 x 64 (upgrade of Windows 8 x 64)
  * Wireless adapter: * Intel Centrino Wireless - N 2200
  * Wireless adapter driver version: * 15.10.0.12 (which is the last for my device)

  I got this Ultrabook since February 2013, and throughout this period, I always had problems with wireless connectivity, even after a factory reset. My wireless icon varies between three States:
  * Internet access
  * Limited (in which case I can't connect to the internet or any other device on the network)
  * Not connected - connections are available (and if I try to connect to the network, it will fail)

  Sometimes my computer would instantly reach the State of "Internet access" at startup and remain in this State. Other times, it would be 'limited' for several minutes after the start of my computer before it finally connected, and even in this case, the connection will drop out every now and then. In the worst case, it would indefinitely remain "Limited" or "not connected", regardless of how many times I reset my adapter wireless or rebooted my computer.

  Until very recently, I always thought that these problems have occurred randomly. However, I noticed recently that I have always a connection perfect, whenever there is no other computers connected wirelessly to my router, and I always have problems more or less when there is at least another computer (or even a smart phone) connected wireless to the router. If there is another computer connected to the router via an Ethernet cable, this causes no problems. It's only wireless connections that interfere with my computer.

  It is only this computer that has these problems; the other computers in my house ever experience these issues, no matter how many computers is online. In addition, my computer is not only these problems with my home router; It has the same problems on the network wireless at my University.

  My question is, how do I fix? Is this a known bug or is my defective wireless adapter? I know that I can connect using an Ethernet cable if possible (I have never problems with Ethernet connections), but this is not always possible at the University.

  Did you remove the old driver Win 8 Intel of the system before you upgrade to version 8.1 to win?
  The old Wlan Intel driver could affect the performance of a Wi - Fi connection.

  The driver update page Win 8.1 says clearly that Intel Wlan driver must be uninstalled and the
  Inbox Windows 8.1 version must be used.
  http://support.Toshiba-tie.co.jp/windows81/drivers/PSU6V_Up_au.htm

• On Satellite L750/0 wireless connectivity issues s 5

  I own a laptop L750/0 s 5.

  I seem to have a problem with my wireless connection, where anywhere not at 10 m from the router the connection cuts in and out with the yellow sign 'limited connectivity' always appears. disconnect and reconnect solves the problem for a few minutes. Ive resorted to the close session of the router.

  the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

  The main thing that annoys me, it's all the others (much older laptops) in our House very much work where mine doesn't. I actually lost performance from where I can get my old toshiba portege m300 to this new wireless signals.

  In terms of information, the computer is running windows 7. Wireless network card is Atheros AR9002WB-1NG.

  If theres any other information that you need, as im sure there will be, I would like to know and ill try my best.

  The router is really new.

  Thanks for your help

  > the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

  The latest Wlan drivers can be found here:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  Please keep in mind that you use the latest driver v9.2.0.419.0

  To be honest, I had the same idea to disable the power save for Wlan and it more often it should work are you sure that you have changed this in the same power station that is used when the laptop is running on battery power?

  However, it would be interesting to know if the Satellite L750 uses the same Wlan 802.11 standard, as do other portable
  In the Device Manager-> properties-> Advanced tab Wlan card, you can choose the standard Wlan 802.11
  Recommend to check this

• Satellite A110-195 - LAN problem (realtek RTL8139)-"Limited or no connectivity."

  I Satellite A110-195 and having problems with the connection on the net, I reinstal driver and aplication but the problem remains, only what happens is that I get messege "Limited or no connectivity."

  Help, please!

  You connect to a cable or a wireless connection?

• Wireless connection dropping on the Satellite C660-195

  Hello

  I recently bought a new Toshiba Satellite C660-195.
  However, I have problems with the wireless connection. When I bought the laptop, it was full of all the annoying and resource hungry programs Toshiba install there. I have reinstalled Windows on the laptop, just install the drivers and software, I wanted and needed. I have problems with the wireless to stay connected. I can detect wireless networks and connect to that I want to be on, I have to add is a connection at home (I'm not fly: P).

  However, the continuous wireless connection down, becoming 'limited' as it says in system tray icon but then turns back on and the process just keeps spiraling on, on and off.

  The wireless I connect works quite well using Xbox consoles, at first I thought it might be the router but after that a second thought if found the wireless on the Xbox is fine then I surely can't be the case? The laptop is Windows 7 64 bit

  Thank you

  Luke

  I wish people would read all the postings first before creating always new posts on the themes that have been already published in the forum:
  Check this domain:
  http://forums.computers.Toshiba-Europe.com/Forums/Forum.jspa?forumid=30

  Update driver Wlan www.realtek.com.tw and disabling power saving for WLan would solve you problems.