Necessary print head

Similar Questions

• Problem with the HP Officejet Pro 8500 printer: clean the print heads each time it is turned on

  Hello everyone,

  the printer HP all-in-one Officejet Pro 8500 (A909a - product n. CB022A) clean the print heads whenever I turn it on. This problem affects any HP Officejet Pro 8500 printer, it is not a problem only of this one I bought. It is a boring bug and annoying because each power clean print heads on involves two bad disadvantages:

  1. waste of ink (each heads cleaning process consumes little ink);
  2. too much time (2-3 minutes) to prepare the printer after plugging.

  I upgraded my printer with the latest firmware available on the HP site (firmware ver. DLM1FN1006BR), but the bug is still present.

  At this point, I ask:

  1. There is a way (or procedure) to disable automatic cleaning this useless to all power on?
  2. Can we communicate with the HP engineers or tell me how to contact directly one of them to indicate the bug and request a new firmware updated?

  Please don't tell me to leave the printer on all the time or that the printheads to each cleaning power is normal behavior! Where then are power and ink savings claimed for this printer model?

  I hope that a solution to this problem. Thanks in advance to everyone will help me!

  Maintenance when the printer is turned on is normal and is required to keep the printheads in good health (not blocked). See here for more information.

  With respect to energy savings, the printer automatically goes to low power mode when the don't feel not for awhile.  It is not necessary turn the unit on to save energy.

• HP officejet pro 8500 a909g: print heads

  my printer has stopped printing in black ink, even if the ink level is more than half full.  Ran "clean print head" and he ran forever.  Still not printing or copying in black.  color copy.

  Hey @ahornplayer58,

  I would like to help you to solve the problem that you experience when you try to print in black ink of your HP Officejet Pro 8500 Wireless all-in-One Printer today. Thank you for troubleshooting that you have completed before reaching out for support, including. Right now, it sounds like you have a defective black cartridge or defective printhead. In this model of printer, you have two print heads. There is a printhead magenta and cyan and a black and Yellow Printhead. If a replacement black cartridge fails to resolve your printing delivers a replacement black and Yellow Printhead may be necessary. Saying that, there are still a few troubleshooting steps that we can try before replacing anything. Can I please you follow the steps below.

  To start, please click here to access the troubleshooting steps. Once the support document opens please run through the solutionand four Solution. This includes all sub-steps under the two alternatives. A print head cleaning may be run up to three times to resolution. If you make three Printhead clean nothing helps, please do not proceed with any additional cleaning ink is used to clean the print head system, and you will just be wasting ink if you want to go forward.

  If the problem persists, the next step listed would be to replace the black and Yellow Printhead. However, it is never a bad idea to first try a black cartridge.

  Please reply to this message with the result of your troubleshooting. Good luck!

• C-309 g HP Photosmart Premium: Incompatible print head - new cartridges for C309g

  Cleaned all the contacts on the print head as shown on the HP website that I wasn't getting any 'black' to get out.  All other colors worked very well.  Noticed that there is a generation of black ink on the print head upward.   Put everything in.  It did the alignment, but he does not terminate.  I had a recording error to restart the printer.  This and now I have and incompatible print head message.  Open a new ink cartridge and I still get the same error.  In addition, all went out again and verified, and there was ink black build-up on the contacts on the print head again.  Any suggestions?  Ink cartridges HP isn't some off the mark.

  Try these Youtube videos.

  https://www.YouTube.com/results?search_query=C309g+PRINTHEAD

  Find out more if necessary.   If this does not work, your printer is toast.

• HP 800ps: misaligned print heads and tracking errors

  It seems to have problems with the growth of transport often does not complete diagnostics because errors appear:

  error 79:04

  susprimitives., 221

  error 86:01

  carmotor.c, 2403

  error 7904

  Mech.c 1299

  error 02:10

  SB.c 228

  error 79:04

  Mech.c 1299

  error 02:10

  SB.c 228

  error 7904

  inkmem.c, 2257

  the plotter was hit, thank you

  

  It seems that that's what the user tried to do it like the example comes from the print head alignment.  First thing you want to do is to clean the MICR band that runs through the carriage Assembly and has fine lines.  Use a damp cloth and go easy on the encoder strip across from left to right and from right to left.  If necessary, turn off first on the plotter and when the carriage moves out of the right side, unplug the printer.  In this way, you will be able to move the carriage to the road that you clean the encoder.  Do not press fort or own to hard that these lines have been known to come off.  Slowly, switch a soaked cloth on one side to the other.  Now, it is clean when you get are more black marks on the canvas.  When the truck is off to the right, you want to move using the belt to see if the action is smooth or bumpy.  So chaotic that would indicate that the belt needs to be replaced.  The last element is transport crossings.  If you look down at the bottom of the carrage to rails, you will see a screw on each side of the carriage house.  Make sure that the screw is not loose.

• HP Officejet Pro 8600: Cleaning printer heads

  I replaced my magenta cartridge with an original 951XL. When I print the magenta ink is streaked. I did 3 cleanings of procedure and nothing has solved this problem. Now the yellow begins to do the same.  After the execution of a progress report on the system of distribution of ink they are still coming striated. The print head may be failed? Thank you

  Hey @Zen540,

  Thanks for getting back to me on this subject. I'm sorry to hear that the steps I provided could not solve your problem of print quality.

  The mechanism of the print head at a cost of e-all-in-one printer HP Officejet Pro 8600 about 150 US $. And there is always the possibility that in your HP Officejet printing system could be defective. Therefore, if you install a new print head and it fails to solve the problem, that a replacement printer would be necessary.

  At this point, I would recommend reaching out to the Technical Support queue by phone to explore the additional hardware options.

  HP Technical Support can be reached at the: 800-474-6836.

  If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  Worldwide contact HP

  When you talk with the phone support agent, please notify them of all the troubleshooting steps you have completed and the results of these measures.

  I wish you good luck going forward with this!

• DesignJet 5500: print head print test very good page, but I still get the error message to replace the printhead

  On my DesignJet 5500, I rswitched the ink tubes, printheads and printhead cleaners dyeing anti-UV, 81 to 83.

  I got an error message saying that the black print head needed to be replaced so I bought another head black printing and after that, I was able to print a test page that shows all the colors (image quality page?).

  Magenta not give not any code of error before, but now I get an error message saying that the printhead magenta must be replaced, even if magenta print well on the printed test page.

  Hello

  The printer give you a warning when the health of the print head is low, but it will continue to print.

  If the problem has been solved after all print head replacement can be that a print head cause others to fail

  Or, just a few bad print heads

• 7520 new stuck in the installation phase. Print head move load ink cartridges

  I'm stuck in the new phase of printer configuration. After running through the commissioning of questions and I opened the cover to charge the ink cartridges and the print head did not move. I ran across several reset process... Unplug the printer. Wait 60 seconds and plug it in again. Browse the configuration... Unplug the printer... more.

  This printer does not seem to be any cartriages.

  Hey JohnTT,

  Sometimes, these printers come with packaging that holds the printhead completely to the right at the gas station.  This avoids damage to the product during shipping.  You see all plastic parts orange that it may contain in place or Blue Ribbon?

  So, have you tried the carriage to the right hand?  Can it be moved or is it blocked?

  If the printer still will not release the print carriage after the power cycles and move it by hand, then I suggest you return the product and return to the retailer of purchase or by calling the HP Technical Support to see about a replacement.  The phone number for the USA / Canada residents is 1-800-474-6836.  If you are not in this region, click here.

  I hope this helps.

• Photosmart Pro B9180 'Replace due to defective print head' WARNING

  My B9180 gave me the msg "replace the defective print head" after a period of inactivity.  I'm using Snow Leopard on a Mac Pro 10.6.8.  The printer went through several periods of non-use, since I bought it used, but almost nine.  Usually, I experience white lines in my impressions after using the printer, I've always been able to fix by cleaning of the nozzles and/or the print heads, either automatically, or manually.  The last round resulted in the warning "defective printhead" even after repeated manual cleaning.  In fact, the process to put off the printer and back, with and without unplugging it, led to 'replace' warnings for ALL the printheads several times, only 2 print heads a couple of times a moment seems to be giving me just the consistantly 'replace magenta/yellow print head.  The strip of plastic that surrounds the ink nozzles is loose to the point of current on the PH.  My printer is no longer under warranty, but before I spend money on phone support and new print heads, I want to look at other possibilities.  The book says that if the manual cleaning of the printheads does not, HP support should be contacted, suggesting that there could be other possible remedies, before you buy new print heads.   I wouldn't begin to buy new print heads to find that again, they will not work because of some other problem.  I am also concerned by the other warnings of print head, even if they did not intervene now.

  Also, opening lid for cleaning of the PH, I noticed a lot of ink accumulate in 4 coarse foam pads, each in its own little tray located inside the printer on the right side.  some of them were overflowing. / I carefully daubbed a part of the ink with q-tips, but I wonder if this condition could be or cause problems.

  Ideas?

  Finally got tired of waiting on HP.  Expected response Bob during the 'days of Forum' or whatever they called.  My problems with their goods should not have affected them too!

  FYI, I ordered a new printhead magenta/yellow, installed and still had "replace print head faulty warning."  Has released the new printhead, cleaned of some sort of clear, gelatinous * beep * of gold contacts with a q - Tip and reinstalled.  Surprisingly, printer started working.  (Took a lot of time to do her routine 'thump, bump & hum'.)  Don't know how long it will last.

  My next printer will be a Canon or an Epson!

• DesignJet 1050c more: 1050c print head cleaning

  Hi all

  I recently bought a 1050c more printer in fairly decent condition. I used to use a Roland SP540v at the office but this 1050c was home so I'm somewhat familiar with printers large format.

  His print beautifully after I replaced the timing belt, new valves of printhead on the ramasseherbe Assembly and removed all the air from the system. The only thing I noticed when I got all the covers off the coast has been the print head cleaning.

  The cleaners C, M and received this pleated filter sitting at the window near the wipers but the black does not. Is this normal? I can see what appears to be a sponge sitting at the front of the vacuum cleaner that I don't see in color.

  Refurbishable are printhead cleaning products? I only ask because it will be a unit of the House and I would try save as much as I can where I can.

  Kind regards

  Select this option.

  I just went down and checked on my 1050C cleaners and Yes, they are the same.  Also the same on the cleaners of the 5000 series, IIRC.  Foam on all colors but black without foam.

  Can you tell me where you extracted the floodgates of print head?  Also, I have a problem with the air in the lines on my 1050c and seeks to replace the system of whole tube by a refurbished.  But if I can try to solve it by simply replacing print head valves, I could even quite a bit of money.

  Thank you!

• DesignJet 1050c more: 1050c failure print head

  Hi guys,.

  So I have a 1050c that I had recently worked, there done upon arrival have air in the black line. I replaced the nozzle which leaked onto the station transport and removed all the air from the line. It worked perfectly for the last two days. Ive kept a close eye on the tube system to ensure no air flow. Last night when I tried to print, it came with printhead failure on black background.

  Now its almost certain air went up in the head after the first print test I did with the printer, I think it was the test of the palette. That's what prompted me to check the tubes in the first case.

  After I got the error last night I tripled checked the lines for all the bubbles that their absence. I also pulled the head and checked the nozzle and there certainly no air either, when I put the printhead in the unit, says its fine all it prints perfectly 3 or 4 passes and then triggers the error. If I reinstall it, it still print 4 or so passes and then triggers the error.

  Is there a chance the other than the head thing, I just want to avoid the replacement of the head to find her something else cause. I'll try and rinse the head with ink to make sure there is no air inside, could give the old head a new lease on life, but I have another head on command in any case.

  99% of the time it's a defective print head.  If the print head has got to air inside the first time you used it, then he should be replaced because there is no way to remove the air unless you can fashion a form of suction device that attaches to the side of nozzle and do enter the PIN that normally goes into the nozzle on the transport of ink.  A few years ago, I saw a device that somebody foreign did but have never seen one that was produced for the market.

• Photosmart eStation C510: I have a Photosmart eStation C510 series with a print head problemo

  Error message indicates that there is an unknown problem with the print head.  When I went to the customer support told me that this model is no longer one of HP services

  Welcome to the community @mickster71 HP

  I wanted to reach out to the issue you are having with the print head on your printer Photosmart C510. See the link below to see if these measures can help the issue. If this isn't the case, then looking at needing a new printer. You can call the phone support to see what are your activities in the options if this happens.

  'Ink system failure' or "0 x... "Error code is displayed

  Hit the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Contact HP:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• OfficeJet Pro 6230: Error Message: incompatible print heads

  The printer is not even a month and has worked perfectly, until last week when he simply stopped Mid-print page. There are no jams, no flashing lights, it just stopped printing. I turned it and turn it back on and that's when the ink lights began flashing. First there was black ink, which I changed with a new cartridge (even though I know that the configuration it was not empty). Then each colored ink lights began flashing. I replaced all four cartridges with the new HP ink and the Scan doctor says that the print heads are alternately missing, damaged or incompatible. The message passes whenever I check. I am at a loss and impossible even to contact someone to get this repaired thing (because it is still under warranty).

  None of the troubleshooting techniques worked. I had all the tried before they have been suggested, so I ended up contact HP and receiving a replacement printer. We'll see how it goes.

• HP Officejet Pro 6835: Print head: missing, defective or Incompatible for 6830

  My 8830 printer is only 6 months old and today I just received this message "print head: missing, defective or Incompatible. Tried to reset and same question as other messages. It seems that he is a typical problem with this printer. Someone can help or will it take to complain about Costco for the sale of this product?

  Hello
  
  Thank you for using the HP forum.
  
  If you receive this error, is there nothing more you need to do, except to contact support.
  
  Depending on where you are in, please select the appropriate link:
  
  Series 6800 printer supports training US, Asia
  http://support.HP.com/us-en/document/c04839288
  
  Series 6800 printer supports statement Europe Middle East Africa
  http://support.HP.com/us-en/document/c04839289
  
  Thank you.

• HP Officejet Pro K550: Software to clean the print head

  I need tool box for old HP printer: HP Officejet Pro K550, for 10-64 bit Windows.
  I need a software tool to clean the print head!

  Hello

  The HP Toolbox software is no longer available for your printer for any later OS such as Windows 7, 8 or 10:

  http://support.HP.com/in-en/document/c03467279

  You can align, clean and calibrate the printhead from the printer itself by using key press combinations.

  See page 33 on its manul below to perform all the tasks of cleaning for the front panel of the printer, such as the cleaning of the printheads:

  http://h10032.www1.HP.com/CTG/manual/c00501024.PDF

  Kind regards

  Shlomi