NOR-DAQ

Similar Questions

• How can I change the target directory for NOR-DAQ 6.9.3?

  I try to install NOR-DAQ 6.9.3 on a new laptop computer.  I tried to change the target directory, but the installer does not allow me to change it.  Is it possible to change the directory?

  When you say that the installation program does not let you change the directory target, you receive an error?  In my view, is it possible to change the target directory by selecting the feature in the feature tree, then by manually changing the target directory to the bottom of the installer.  When this is done, a pop up will occur who says a new folder will be created to save the files to.

• MAX does not recognize NOR-DAQ traditional (old) devices * HELP

  I have a card PCIe-6259.  I want to use blocks of input-output in my program .vi (read Port DIO-DIO Port writing reading Digital Line), so I installed the version of NOR-DAQ traditional (old) devices 7.4.4.   But when I got to MAX (measures & Automation) and look on the left side under devices and Interfaces, I do not see the Tradional-NOR-DAQ tab; I see only the devices NOR-DAQ-mx, PXI, series and parallel system.

  Then when I go to run my program I get the error: error-10401 took place in a DIO Port Config Possible reason (s): NOR-DAQ LV: the specified device is not a product of National Instruments, the driver does not support the device (for example, the pilot exited until the device has been supported), or the device has not been configured using the Explorer Measurement & Automation.

  So, how do MAX to recognize that I have installed NOR-DAQ traditional (old) 7.4.4?

  Thanks for the reply!  I realized this too after going through the files for example... but thanks for the confirmation.

• CR1000 are accessible using NOR-DAQ?

  Hello

  I'm trying to control a CR1000 datalogger using Labview. Is it possible to configure the available CR1000 in NOR-DAQ?

  Thank you!

  Why do you think you can use drivers OR a product OR NOT?

  NOR-DAQ is for products OR.

• Problem setting Legacy DAQ board using NOR-DAQ 6.1 for Labview

  I know that the Board of Directors is an old legacy product not supported by NEITHER, however for a low-budget project, I have 3 of these AT-MIO-16 x cards and the need to use them.

  I know I got this job in the past not distant os, however, for the life of me can't get things sorted and work.

  You use a NT box, in which this configuration used to work... uninstalled and started fees for other reasons, and I can not get the NOR-DAQ 6.1 to support LAbview 6.1 or 7.1.

  Of course, I understand the OR-DAQ 6.1 should be used for Labview 5 and older, but also know this has been successfully done in the past.

  I downloaded all knowledge base articles dozed or both support and remember to use successfully the last time that I set up so I know not somehow it works.

  My configuration is: AT-MIO-16 X to the bus combo board (called work)

  NT PC

  LabVIEW 6.1 or 7.1

  NOR-DAQ 6.1 is the most recent to support this card.

  However, it will not install its support to its latest versions of Labview and I get errors, crashing, or missing files, when I followed various circumvention of knowledge base solutions.

  I was hoping that someone has a documentation somewhere how to handle this, because it really is a matrix of spaghetti.

  I can get NOR-DAQ support files installed, and Configuration Manager works well, finds the map and allows its parameters to be defined.

  But when I load the DAQ vi of any type, Labview accidents and the wizard of data acquisition channel does not work at all (no error).

  Thank you

  Yes, the installation program from the folder of disks for NOR-DAQ 6.1 on the ftp site has worked well.

  Workaround. Thank you

• Verification of task names valid in the basis of NOR-DAQ

  Hello

  I have a question about the configuration of the tasks in the version of Base of NOR-DAQmx (I need basic because the application will need to be able to run on both Windows and Mac computers). The material is a box USB-6009, ordered through LabView. When you create a task inside LabView, is it possible to tell if the name you choose is already in use or not?  Similarly, is it possible to get a list of and if all tasks are running?

  The context is that I have a subroutine that made a brief burst of acquistion of analog input and then passes the result to the caller. I would like also to the subroutine to run standalone for different testing purposes. Normally, I would have the subroutine create and configure a task, the measure and then close the task. The problem is that the process of create/set up/start takes about 200-250 milliseconds (the measure itself is about 20 ms) that is long enough that I don't want to go through it whenever the subroutine is called from the top (I need to call this routine and do some other stuff a few times per second). So what I would is have the name of the task as a control on the subroutine, test that the value is a valid and if not valid only the initialization/etc. in the context of the subroutine, but if the subroutine has been passed a valid task from the top to skip a step all the time.

  Looking through all of Base of NOR-DAQ functions, it doesn't seem to be something that allows me to do this kind of check with the exception of brute force to try to create a task and trapping so all errors that might be generated.

  Suggestions (or ways) welcome.

  Kelsey,

  It seems that the property node is a component DAQmx, not a component DAQmx Base .  I can't find any DAQmx Base property nodes.

  dmsilev,

  Try to replace the property node of the tasks with the DAQmx Base get tasks.vi.  It is not in the DAQmx Base palette. It's a Subvi DAQmx Base create Task.vi.  Caution: when you use a Subvi, which isn't on the pallets, know that they are generally not documented well and are subject to change in future versions of LV

  

  If you weren't aware, DAQmx Base is written in LV and almost all the diagrams are not p [rotege so you can look inside and see how things are doing.

  Lynn

• NOR-DAQ traditional vi not found in NOR-DAQmx

  Hello. We hope to control a detector via NI PCI-6533 (DIO-32HS). Our colleagues have implemented control programs in BT 7.1 to 7.3 of NOR-DAQ traditional. Now when we opened their programs on a PC installed with LV 8.6 and NOR-DAQmx 8.9, many vi was not located, including "DIO config.vi", "DIO wait.vi", "DIO clear.vi", "DIO read.vi", "Reset.vi Device", etc. We realized that they were supposed to come from vi.lib\daq\digital.llb and a few other .llb in the same folder. Apparently vi.llb\daq was installed by the traditional DAQ.

  We do not believe there is compatible with LV 8.6 traditional DAQ, which means that we need to replace those 'DIO *.vi' or 'Device reset.vi' with their counterparts DAQmx.  Could someone shed some light on how we should start working on that?

  Thank you very much.

  Xiaolan,

  Indeed, there is a traditional DAQ driver for LV 8.6. The installation can be found here.  I hope this helps.

• NOR-DAQ traditional to NOR-DAQmx

  I am a neophyte of LabVIEW.  I inherited a previous employee long gone from the company, so that I work a LabVIEW project.  The project has been written using NOR-traditional DAQ and I need some update OR-DAQmx so that it is 64-bit capable.  Of course, I ran into trouble with the VI first that I try to put in level.

  This VI was built with LabVIEW 2011 SP1 and I need to replace the Config AI, I start, I Read, Index channel, control and HAVE clear screw with their equivalents of NOR-DAQmx.  Upgrade to SP1 2013 LabVIEW is possible if that makes things easier.

  Now here is the tricky part.  I want to keep the terminals on this VI even if possible.  This VI is used in several places and a few different programs and I want to make the change as minimally invasive as possible.  If possible, I want the changes must be made within this VI.

  I am looking for any help and or advice. Thank you.

  First, abandon all hope to keep the same connector components.  It is possible, but it's foolish to try. (Just trust me, OK?)

  Read these articles in the knowledge base

  http://www.NI.com/white-paper/3021/en/

  http://www.NI.com/white-paper/4342/en/

  What you're trying requires skills usually not developed in a neophyte of LabVIEW. (And you start with the 'Spaghetti' code - this is not 'Fun') Do an internship of audit and meet with your representative local of NOR.  Chances are that some local expert advice will point you away from some serious mistakes.

  Take care

• NOR-DAQ traditional (old) devices of measurement and automation explore 4.7 with LabView2010 under Windows 7.

  In measurement and Automation Explorer 4.7, with LabView2010 in Windows 7, peripheral OR-DAQ traditional (old) appears under devices and Interfaces and it allows me to create a chassis SCXI-1000, and she agrees "Reset for NOR-traditional DAQ.  However, it does not search the modules in the SCXI1000, and when I ask 'trial', he says 'Impossible to test the chassis at this time.'  The entrance of NOR-DAQmx devices for the SCXI-1000 chassis has no problem and detects the modules very well.  I need the Legacy DAQ to a popular former teaching tool that has no equivalent in NOR-DAQmx.

  Unfortunately, NEITHER-DQA traditional (old) for Windows Vista and 7 functions of the only driver on Windows 7 32-bit, as seen on the page of the driver at the end of paragraph 1 Solution. I recommend you move your program to DAQmx.

• How to define logical tristate using NOR-DAQ 6212 in c#

  Hello world

  I am very new to NOR & help each of you experts out there.

  As the subject says, I'm trying to set digital output at tristate DAQmx & c# channel. I found the link on the Tristate property, but I don't know how to use it. http://zone.NI.com/reference/en-XX/help/370473H-01/mstudiowebhelp/HTML/bd33b0d/

  Any help would be much appreciated!

  Thank you.

  Hi kasrus,

  You set the property using the following syntax (after creating your task):

  digitalWriteTask.DOChannels.All.Tristate = true;

  As help document states: "you must commit the task for this setting to take effect."  The help document also highlights when the value of property compared to a reading or writing.

  This refers to the status of task template DAQmx:

  State of task model

  http://zone.NI.com/reference/en-XX/help/370466AC-01/mxcncpts/taskstatemodel/

  Methods of configuration will move your task through this model of the State, but you can also control using the syntax in the article below:

  Check, committing, start and stop of NOR-DAQmx tasks programmatically

  http://zone.NI.com/reference/en-XX/help/370473H-01/mstudiowebhelp/HTML/verifycommitstartstopdaqtask/

  Kind regards

  Kyle S.

  Technical sales engineer

  National Instruments

  http://www.NI.com/support

• NOR-DAQ + NOR USB-4431: error 233054

  Hello everyone,

  First of all, here is my config:

  -Dev PC: Win 7 32-bit

  -LabView 2009 - 32-bit

  - NI DAQ 9.7.5

  -Card acquisition: NI USB-4431

  The problem:

  When I run my app just after connect my DVR to my PC (or after startup) card, the DAQ Assistant gives me error 233054:

  

  I not found any explanation on this wonderful tool that is the internet, so I come here!

  The only way I Born to move forward, is the NOT-MAX aperture, ask to make an acquisition, ask to do a generation (that work) and then I can go back in LabView and run my program!

  The problem seems to come from the initialization. But I don't see what I need to do to make it work every time! Any idea?

  Best regards

  Harold

  Hello

  I just checked the daqmx and labview driver compatibility. I noticed your 9.7.5 daqmx driver version is not compatible with labview 2009, therefore, you have this agreement.

  The latest version of LabVIEW 2009 daqmx is 9.7 see below

  DAQmx and LabVIEW version compatibility:

  http://digital.NI.com/public.nsf/allkb/B0D5630C0A50D5C6862578E800459248

  So is this you can 9.7.5 uninstalling and reinstalling daqmx 9.7 see this link

  Uninstall the software

  http://digital.NI.com/public.nsf/allkb/AC6ED75D3D93375686256E8E00245F0D

  Best regards.

• Help with the NOR-DAQ example Code

  Hello. I just started to work with the NI IBS-6211. It's the first ADC I have ever used, so I'm farily to this news. I have some programming knowledge. After a search in the installation files, I found some examples of C Code that runs in the command prompt. I changed an a bit to get it to do what I want. My question is...

  Now, I have a few problems. I am trying to print a voltage in the command prompt. I hooked up everything and I used labview to make sure that everything works as it should (it does!). When I compile the C program and the run, instead of returning a voltage that is just acquired points and I really have no idea what are these 'points '.

  Here is the main part of the code example:

  DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
              DAQmxErrChk (DAQmxCreateAIVoltageChan(taskHandle,"Dev1/ai0","",DAQmx_Val_Cfg_Default,1.0,10.0,DAQmx_Val_Volts,NULL));
              DAQmxErrChk (DAQmxCfgSampClkTiming(taskHandle,"",10000.0,DAQmx_Val_Rising,DAQmx_Val_FiniteSamps,1000));
  
              /*********************************************/
              // DAQmx Start Code
              /*********************************************/
              DAQmxErrChk (DAQmxStartTask(taskHandle));
  
              /*********************************************/
              // DAQmx Read Code
              /*********************************************/
  
              DAQmxErrChk (DAQmxReadAnalogF64(taskHandle,1000,10.0,DAQmx_Val_GroupByChannel,data,1000,&read,NULL));
  
              printf("Acquired %d points\n",read);
  
  Error:
  

  And then he moves right down to the exit clause. Is there documentation anywhere that tells me what DAQ command should I use to print a voltage continuously updated reading? (As a decimal number, such as 5.21V for example).

  Thanks to you all

  John

  John,

  The data acquired by DAQmx are written in the array called "data".  The number of points DAQmx wrote in this table is stored in the variable 'read' which was adopted by reference in.  To print the values returned, you need to loop through the array of 'data' and print each value.  See this help topic for an explanation of DAQmxReadAnalogF64.

  Dan

• Nor-daq-mx: generate multiple samples

  Hello!

  I need to send a binary file multiple to a multiplexer, when I get a TTL signal, then I need to read the signal for each sensor.

  But my vi, just send 1 one after the other: /, I tried a lot of things, but I'm stuck.

  Edit: FYI I use one or pci6251 and labview 8.5

  Here is a simplified version of my VI and and draw little I did for you.

  u didn't do well understand what I want to do but u can have another solution, in any case, I managed to succeed.

  check the VI I attached, it works.

  at each TTL, I generate a pulse train, and the binary words are synchronized on the pulse train.

• Nor-Daq 6251 set hour/time between samples

  I'm trying to calculate the expected error for an experience that I do and I don't know if I've done enough to determine the 'break-in' or the time between samples.

  We use 8 differential channels to the maximum sampling frequency, the card can do (1.25. MECH / s). If I understand correctly, the minimum time between each sample must be 1 / 1.25 M, or 800 nanoseconds, such as the maximum time between sampling channel 1 and channel 16 would order 12uS (800nS * 15). If the expected voltage settings are the same for each channel (+/-10v), would a break-in? If so, how long?

  In addition, if a channel is upward, and its tensions have an offset, DC on 5 or 6 volts, should that severely increase break-in if all other channels averaged about +/-1v?

  I'm sorry for the basic question, I couldn't find a straight answer in the documentation.

  Hi LSUgrad85,

  When looking for specific device information detailed Specifications for this device will usually provide the details you are looking for.  After the back if you have questions about the information in the detailed specifications.

  I hope this helps!

  Kind regards

• The code runs fine for 1 time. NOR-DAQ: command requires controller gpib controller

  Hi all

  My labview code is attached. He controls a powersupply lakeshore, keithley and sourcemeter multi-meter and a GM08 Gaussmeter.
  The code works perfectly on the 1st round.
  However, on the 2nd round, the initialization for the sourcemeter (KE2400) returns an error.
  The code works well again after cessation of the VI and it works again.

  I have no idea why this is happening, any advice would be helpful thank you! (as with all tips to make my code better in general)

  My big loop is of my readings on average.

  If the error occurs at initialization, then the question is not the shift registers. All of your entries to the initialization did not all local variables or something weird, so it has nothing to do with the values changing with each race. That leaves the issue lying with the instrument itself, or communication with the instrument.

  When you first run the application is complete, there are errors? Run VI close very well to close the connection?

  I suggest you do a little test VI passing right through the screw, using the Sourcemeter to see if you can dial in on the problem. If you test VI initializes and works fine again and again, then it might be a problem with your errors or manipulation of communication management.