PC keeps restarting after the Windows startup screen

Similar Questions

• Satellite P300 itself keeps restarting after the initial splash screen.

  My Satellite P300 itself keeps restarting after the initial splash screen.

  Start-up of the first screen with the F2 and F12 options down is displayed, the screen goes black, then a cursor appears in the upper left corner and flashes once or twice. Then the laptop stops and restarts and goes through the same process again and again.

  That's all with the power adapter is plugged in. If disconnected, he goes through the above process and close with no reboot.

  Any help or advice would be much appreciated.

  Post edited by: aic-poppy

  Start your laptop and enter the settings of the BIOS (F2). Set to its default value. Restart your computer, and press F8 to access the advanced boot menu.
  To start the laptop in safe mode and let us know if it works, try it please.

• Satellite A210 - turs screen off after the Windows startup screen

  When I start my windows there is the splash screen. After that, my screen goes off and cannot log on to windows.
  Satellite A210
  ATI Mobility Radeon HD2600

  Where can I get some old drivers for the ATI Mobility Radeon HD2600, that I can install without starting windows?

  > Where can I get some old drivers for the ATI Mobility Radeon HD2600, I can install without starting windows?

  Please don t get me wrong, but I think you're on the wrong track.
  (Graphics card, LAN, etc.) device drivers must be installed in the currently running system (i.e: Windows OS, etc.)

  I m sure; pilot isn t the problem if nothing is visible on the screen.

  First of all, I would recommend you to connect the laptop to an external monitor/screen just to see if something would be visible on the screen 2.

  But just a question: have you tried to start Notepad using a boot disk (windows installation disc, the disc recovery Toshiba or similar?).
  Maybe the Windows system is confusing upward and therefore, you are not able to start the system? In my opinion, you should test this option.

• After removing the Tdss rootkit, computer laptop My Windows Vista Home Premium keeps restarting after the connection. __

  I had the Tdss rootkit on my laptop and removed using TDSS Killer of Kasperky. After the reboot, I have connected and saw a box that displays "Please Wait". After 5 to 10 seconds, my computer restarts. After the reboot, it shows options for Windows Vista loading, i.e. the safe mode, safe mode with network. I chose the mode safe mode with networking and everything works fine. The system properties box opens automatically. When I try to boot into normal mode, he repeated restart after the connection. I tried to run a restore of the system into safe mode with networking, but it tells me something about the system restore is in mode offline. I hit a brick wall and don't know what to do next. I don't want to if I have more options to factory default restore.

  The TDSS rootkit is very destructive.  It is not uncommon to make a computer work is not properly after removing it.  I advise you to restore your computer to factory default.  Not only is this the best option, it's the safest option.  I wouldn't consider the computer to be trusted without going through the restore process.  Even if you can be sure that 100% of the infection has been removed, you have no way of knowing what changes the malware made to the settings on your computer, which may be exceptionally vulnerable to future malware attacks.

• Phone keeps restarting after the last update

  After the start of the update of the configuration via Sony PC Companion, this program that, at the time, my PC is getting ready (and it will take some time) himself said update I can unplug my phone or not, so I am disconnected and then I pluged in again. Phone started the update (it is turned off and started the update) and release suddenly came out telling me that my phone is connected. Sony PC Companion tells me to unplug and restart, after that my phone keeps restarts all the time.
  HELP ME GUYS!

  Try a system repair using PC Companion as this will often fix questions - this will be factory reset your phone and erase all data

  Turn off your phone and unplug the PC (Hold to increase the volume and power for 10 seconds)
  Start PC Companion and select the area of support then updated my phone/Tablet then blue fix my phone/Tablet and follow the instructions on the screen - when prompted connect your phone turned off always press and hold volume or back button - this should begin the process of repair or reformatting

  If you use Windows 8/8.1 or a 64-bit operating system and then adjust the settings for PC Companion and run in compatibility mode and choose Windows 7 or XP

• Satellite Pro L450D - 12 X is not booting from the windows startup screen

  Hello, my laptop Satellite Pro L450D-12 X has been set up on and after awhile, window repair system popped up.
  After a long time he closed and restarted, but it does not start at the windows logo screen. It just stops after the splash screen and the screen goes black.

  Please can someone help?

  Hello

  Looks like the system is corrupted
  Try HARD drive recovery

  Turn on the device, press F8 and choose fix my computer.
  Now choose the recovery of HARD drive in the list of available options.
  This should set the camera back to the factory settings

  But this procedure works only if the HARD drive is OK.
  If the HARD disk is not OK, it will not work

• Windows 7 stuck on the Windows startup screen. Help!

  I was playing a game (Counter Strike: Global Offensive - on Steam) on my PC I got the blue screen error was 0x000000A3, after that I booted my PC then it got stuck on the Windows splash screen. Now, when I start my PC it gives me only 2 options, "start Windows normally" which leads to frozen Windows startup screen and it gives me this: '(recommended) launch Startup Repair' that I have used and tried all the options, except the command prompt like I do not know how to use it.

  My PC is a Windows 7, Asus

  Hello

  Often, this will work when the built-in repair software will not.

  Make your own information system repair disc in this tutorial:

  "How to create a Windows 7 system repair disc"

  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  "This will show you how to create a system repair disc Windows 7 to be able to use to start the system recovery options to help recover your Windows 7 installation, if you have not a Windows installation disk, can't find your Windows installation disc or can not access the recovery options provided by your computer manufacturer.

  A system repair disc is not able to install Windows 7.

  Note

  If you are unable to start your Windows 7 to create a Windows 7 system repair disc, and then you could create on another computer for use on your computer. »

  _____________________________________

  Then, use this disk for System Recovery Options:

  "System recovery options".

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  "How to run a startup repair in Windows 7"

  http://www.SevenForums.com/tutorials/681-startup-repair.html

  See you soon.

• Inspiron 9300 screen turns off after the Windows Logo screen

  Inspiron 9300 my wife became severely infected.  I thought I had some weird things start popping up of the problem decided to wipe the hard drive and start over.  Unfortunately, I don't have to restore disks when I bought the computer.  I install windows xp pro service pack 2 full retail version.

  Installation was not a problem until I installed the driver ATI Mobility x 300.  I followed directions for installation from the website, do the installation of xp followed of the dell system software update followed of chipset followed video driver.  After that whenever I put on, the screen turns off after the Windows Logo.  The computer is still running and if I plug an external monitor everythng is fine.

  I tried all the troubleshooting tips I've seen in this forum.  I did a full install twice. made of safety boots (all right), started in VGA mode (works fine), I ran diagnostics from fn on startup, including express, extended and video tests and they pass all the controls.  I'm sure it's a software problem, but have been unable to solve.  I've updated the ATI bios although when I run it says already installed and done one installs x 300 driver on 6 ttimes own.

  I know it must be something simple that I'm missing. My system is the Inspiron 9300 with 2 GB of ram and the mobility x 300 card.  Any help would be appreciated.

  
  

• My computer starts and I get the Windows startup screen, then my screen goes black and the computer is frozen I guess. Stopping and restarting do not work.

  I get to the black screen with the Windows XP logo and the bar of the State, and instead of my forthcoming accounts page, the screen goes black and nothing else happens. I tried the power off to reset and restart, and I can't perform a recovery of the system with the CD.

  Hi cgrosenick,

  -What software changes you did on the computer before the show?

  Follow these steps:

  Method 1:

  Start your computer in last known good configuration mode.

  For instructions, see How to start your computer by using the last good Configuration in Windows XP functionality

   

  Method 2:

   

  Follow the steps in this article:

  Computer stops responding with a black screen when you start Windows XP

• HP G62 freezing at the windows startup screen

  Hi, recently my laptop kept freezing randomly, but now it will not even past "starting windows" when I load up. I ran the two hard drive and who both have memory tests. Also tried everything on the menu after pressing f10 and f8, including safe mode, but all the options keep freezng at windows startup or stops at a black screen and only being able to move the mouse. Any help would be greatly appreciated that the laptop is relatively new. Thank you.

  It's time to find your set of recovery disks or usb recovery media that you created when you set up your laptop.

  If you have not created a set, you have the choice of where to get a set of recovery disks. The cost is usually about $30,00 USD

  Order a HP recovery disk
  from an HP partner

  If your laptop is still under warranty, contact HP for a warranty replacement drive. Refer to the troubleshooting forum and give the representative of I.D. failure HP support: Q4QG9R-54T6LD-9XL03G-60QM03d if requested.

  If it is in warranty, just buy a replacement and remove the original disc and put the new in its place.  Insert the first diskette in recovery agree for the warning to commit to a recovery and image selection recovery plant.

  You can also use the Microsoft Windows COA 25 character license key and install Windows 7 from a usb\dvd Installer. The usb Installer is highly recommended.  You can download an iso file for your operating system here.

  Best regards
  ERICO

• Vista keeps restarting after the installation of updates

  I have IBM laptop computer a customer T61, Vista Home Premium. Starts and goes to the "Configuring updates 3 of 3, then it goes to"shutting down"and keeps restarting."

  I tried safe mode, last good, from CD and repair of Windows, nothing worked.

  Any ideas on what else to do only a reinstall full?

  Thank you

  Ed

  Try this
  http://support.Microsoft.com/kb/949358

• Failed to start after the windows logo screen, please help.

  Original title: STARTUP DO NOT FULLY

  Hi, I run windows XP Home Edition on my laptop, when I switch it on it boots until the windows logo and no more, can anyone help please.

  I tried F11 to safemode etc but is still no more than the windows logo.

  You must be repeatedly tapping / pressing the F8 key before Windows starts to load to access the Advanced Boot Options menu to see the Safe Mode options :)  Keep and tapped F8 until you see the Advanced Boot Options menu.

  If you miss the niche F8 and XP starts to load, you missed it, and you have to start over.

• After the windows welcome screen just goes black?

  After that I entered the password for my laptop, it remains on the Welcome screen. After some time (sometimes) it will move past and I just black. The mouse still works and the cursor can move. No page loads later. I use Windows 8 and this happened for some time. Sometimes this will be repeated but other times it works just as usual. Any suggestions? Please help as soon as POSSIBLE.

  Hi Zachary,.

  This may be a problem with your display drivers.

  What is the brand and model of the PC?

  As you face this problem at random and since you are able to start the office, I suggest you follow these methods and check if it helps.
  Method 1:
  Updates driver may be available through Windows Update.

  To check the updates of the driver,

  (a) at the start screen, type Windows Update.

  (b) click and tap settings on the right side of the screen, then select install optional updates in the results on the left.

  (c) when the Windows Update Control Panel opens, click on Check for Updates on the top left corner to receive a new list of updates.

  
  

  
  Method 2:
  If no updated drivers are available through Windows Update, see the website of your video card manufacturer to see if they have updated drivers available.
  Install the driver yourself
  http://Windows.Microsoft.com/en-us/Windows-8/all-drivers

  Let us know if it helps. If the problem persists, we will be happy to help you.

• my laptop keeps restarting after the installation of updates

  my laptop is stuck at step 3 of 3 (only display 0% complete) after the reboot for updates, then restart again and again, with the same supposed progress, I ve let it doesn't restart on 7 times.still no good.

  Tell me what are the steps to solve this problem

  Hi Amrbialy,
  When your computer is turned on, push and hold down F8, this will bring an option before it starts on your desktop. Choose "last known good configuration".
  If this has no effect. Then do the same thing, except choose Safe Mode. When it boots to desktop click Start > all programs > Accessories > system tools > system restore.

  Then it will give you an option to choose a date to return. Choose a date before you install updates, and then click OK. Restart your computer.

  It will be useful.
  Let us know how it goes!

  Thank you

  Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Change the Windows startup screen

  When Windows Vista starts there are three icons for my listed users.    How can I change the order in which they are presented?   I want 3 icon to appear in the middle.

  Hi, Peter,.

  There's a third-party utility.  This is a tutorial on moving points around in a login screen

  http://bfarber.com/moving-items-around-in-a-login-screen-t6911.html

  Resource Hacker (freeware)

  http://angusj.com/ResourceHacker/

  How to change the Windows 7 logon screen background

  http://www.Novell.com/communities/node/11748/how-change-Windows-7-logon-screen-background