Router connection problems

Similar Questions

• Modem router connection problems

  Hi all

  I am replacing a belkin n600 with router linksys ea6350 router. The modem I have is a Motorola Surfboard SB6141. The belkin router connects perfectly to the modem, but when I try to connect the linksys router to the modem, the light on the router keeps blinking and will never get me connected to the internet. I even tried to connect the linksys router to the router belink when the belkin is connected to the modem. I still don't get any kind of service. Thought it was a bad router and it took for my current home to connect to my modem At & t and it worked very well and I was able to put everything in place. For some reason I don't know why the linksys connects very well with the modem at & t, but not the motorla modem and the ISP that I have in my apartment is Comcast. It does not any sense and I'm heading home in a few days and I really need this connected linksys router belkin router is just too slow. Please I need much help getting this linksys router to communicate correctly with the motorola modem. Also, I used both crossover and straight cable modem to see if that makes a difference and does none of this and I know use cross to connect to the router.

  first of all, make sure that the port on your pc is enabled.  usually, if you enable wifi it disables the ethernet port.  before you turn off the modem and do a factory reset on the router into the RED reset button until the lights on the router are flashing.  Turn the power off and wait 10 seconds then plug it back.  During its initialization connect a straight cable between the pc and the router's lan port.  Also, connect a cat5e or cat6 from the wan port on the router to the modem.  wait until the router finishes starting, and if she opens a browser in itself and then open a browser (ie to try) and put 192.168.1.1 in the address bar.  You should get a connection.  Let the empty user and enter "admin" for the password.  Or if it opens the programme of assistance to load the router you can follow if you wish.  This should get you.

• E3000 router connection problem when I use the telphone

  I plugged my router through my telphone line. When I use my telphone, I can't connect my computer to my router. When I see the available wi - fi networks available, my router does not see. As soon as I get off my phone, I can see my router and able to connect. I thought that my router has two bands and I'll be able to use it. I'm not a geek.

  Help, please. Thank you

  Why is your router connected to the phone line?

  It must be connected to a DSL Modem or a Cable Modem (assuming that the release for consumption).

  Need information in order to determine the question.

  Is your wireless phone a DECT 6.0, 2.4 GHz or 5 GHz?

  I changed my DECT 6.0 wireless phone because they do not interfere with wireless 2.4 GHz or 5 GHz. older phones use the same frequency as the network and can interfere.

  Why so your router on a telephone line?

  How often your mobile phone works on?

• Factory reset wireless router connection problems?

  Hello

  I recently did a factory reset on my HP6745f desktop running Win7 sp1 and I don't know if my problem is with HP or Linksys/Cisco (my router). I already contacted the support Cisco who reported the problem seems to be "a matter of HP, a corrupt driver or other third-party issue" and then offered to help, for a price. I'm hoping to avoid that if possible.

  This office computer is directly connected to the router via an Ethernet cable. Cisco software was that I want to install that 'control' of my router (called Cisco Connect) and when I try to install the software, I get a message saying: "We could not find your router" (that's why the software will not install) - although I am accessing internet through that router. Even if I try to enter my network name and the password, it cannot find anything. I am also unable to access the router via my browser "168.198.1.1".

  I am unable to connect wireless with the same desktop so, my 2 wireless laptops have no problem of connection at all, which leads me to believe it's something specific to my desktop pc.

  The Cisco Connect software has already been installed on my desktop and it worked fine. I guess my question is: someone has any suggestions for me? This could be a driver problem? How can I identify what (s) for 'check '?

  Any help would be greatly appreciated.

  I thought about it! My router can use a "network key" to connect other computers to the router. I guess when I reset my pc all this info has been removed and the router could not communicate.

  I have just created a network key on a flashdrive USB of my laptop, plugged the USB in my office and hop, I reconnected properly. Thanks for the suggestions, I really appreciate the help.

• Pavilion dv4-2160us with Atheros AR9285 and D-Link WBR-2310 wireless router connection problem

  NB sometimes has problem connecting to the router. This occurs when the NP is booted from power, or when the connection of power mode after about a day of economy since his last connected. Although the network sharing Center sees the network to connect to, but shows only "restricted access". But if the power to the router is recycled, then the connection is established. The driver for the Atheros AR9285 is up-to-date. The firmware of the router is the latest v1.05.

  A test ping Google permanently on the NB and a computer that is connected to the router to isolate the problem. Whenever Google is ping successfully, it displays a message and the response time in milliseconds. If the ping fails, the message will be "Ping: transmit failed." General failure. "  It turns out that, while the test on the wired computer worked without a hitch, the NB has shown that at the same time, the internet connection was lost during the time of connection. He then recovered after a few 'pings '. At another time, the internet connection has been lost permanently without recovery, also during the time of connection.

  Anyone has the same problem?

  After changing the security mode WPA2 to WEP router wireless, the problem seems to have disappeared. It's been 3 days and the computer can still make the connection to the router. HP support says that HP wireless network adapter works best with the WEP security setting.

• Router WRT320N to a wired BEFSX41 router connection problem

  Hello, I never thought it would be so difficult. I have problems to connect to a router (WRT320N) so it will be on the same network as my other cable firewall router (BEFSX41). The wireless router works fine because it connects to the internet via the BEFSX41 router. However, the two routers do not see each other and I can't connect two computers, a wired computer, the other laptop wireless to the same network.

  Wired BEFSX41 router uses 192.168.1.1 IP address and the router WRT320N wireless uses 192.168.0.1 IP address.

  Don't know what other information you need. I hope you can solve this problem for me.

  Thank you

  Mike

  For file sharing, it is always better to maintain the network in the same subnet... Connect the BEFSX41 on the Ethernet Port of the router WRT. (LAN-to-LAN connection)... Visit this link for that. If the IP address of the main router is 192.168.1.1 then, change the 2nd router's ip address is 192.168.1.2.

  Make sure that file and printer sharing is enabled... Also, make sure the computer are in the same workgroup...
  Default workgroup in Windows Vista has been renamed to WORKING group. In Windows XP, the default workgroup name is MSHOME...

• New router connection problems

  So I just got a new router delivered to my cause of House, that we had to move to a new location, and that we have obtained will not let me connect to the internet via a modem-> router-> computer.  It works very well when connecting with the computer of my brother through wireless. When wired to the router I get full connected via the internet and so on, but when it comes to my computer wireless router, do not let me go beyond "local only". He remains as unidentified network and can't get more than that.  Ive tried to restore my computer to Service Pack 1 and remove Norton from my computer with the removal tool and nothing seems to work. Ive changed my setting of the router mode 50MBPS and stuff and nothing, defining the network IP and DNS in my Protocol which is in my router and that did not work either, my IP address restarts and refreshing, nope. Im running Windows Vista Home Basic with an Atheros AR5007 802 network card. 11b / g. router Netgear WNR1000v2.  I had a problem with my computer with my last router.

  It's my connection information:

  Microsoft Windows [Version 6.0.6001]

  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  
  

  C:\Users\***>ipconfig/all

  
  

  Windows IP configuration

  
  

  Name of the host...: *-PC

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  
  

  Wireless network connection Wireless LAN adapter:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-24-2B-C8-1A-21

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  
  

  Ethernet connection to the Local network card:

  
  

  The connection-specific DNS suffix. :

  Description...: Realtek RTL8102E Family PCI - E Fast Ethern

  and NIC (NDIS 6.0)

  Physical address.... : 00-1F-16-70-E0-A5

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::a85c:6ec9:2 has 4: bbf5% 10 (Preferred)

  IPv4 address: 192.168.1.4 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Monday, November 29, 2010 14:29:05

  End of the lease...: Tuesday, November 30, 2010 14:29:05

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  
  

  Card tunnel Local Area Connection * 6:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {E418D763-0DB4-4DCA - B 9, 70 - E94D132E8}

  62 A}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 7:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {F2AFB4E5-A1E8 - 415 B-A7B3-A433B3227}

  715}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 11:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

   

  Any help would be appreciated.

  
  

  Well, I tried everything you listed on here and nothing seemed to work. I found a good solution to change my WEP security and he recognized her. Looks like it has problems with the other encryption security. Thanks for your help though!

• Nook Color ereader & connectivity problems with router WRT610N

  I recently bought a new Nook color ereader for my wife. As long as a network administrator, I thought that this would be an easy task to configure the ereader to connect with my Linksys WRT610N router on the 2.4 Ghz band. But I'm running problems when connecting. The question seems to have intermittent connection problems where the meals seem to see the wireless network, authenicates, tries to get an IP address, then connects for a short period or removes the signal very quickly while being right on top of the router with the device.

  By the recommendations of various forums of Nook, I had the best luck with the following...

  2.4 Ghz band settings

  SSID: NookNetwork

  Channel width: 20 GHZ

  Standard channel: 9

  SSID Broadcast: enabled

  Security mode: WPA2 Personal

  Encryption: AES

  Passphrase: set out

  Key renewal: 3600

  UPNP: disabled

  RTS: default

  Defragmentation: default

  Tag: default

  However, the problem still resides in an intermittent connection to the wireless network. I also tried various arrangements of the channel to both channels 1, 6 and 11 with my best cponnecting chance to channel 9. I also played with the security and disabled all together and have plugged but always file (will not however run the unsecured network). Also try a tag value of 75, a framework of fragmentation of 2306 and 2307 RTS setting. My computer laptop while run and connect properly.

  I use the latest software updated both on the color of the corner. I am at the end and have searched high and low to get suggestions, and have not yet reached a compatible connection. Please help... Thank you! And my wife thank you in advance! Smiles!

  Mike

  Hi death,

  Thanks again for your comments and your concerns. Really appreciated!

  I took your advice and contacted Barnes & Noble for a new replacement and am waiting for the reception of the new unit as I type. If all goes well, we have reduced the problem and the replacement ends at our misfortunes... smiles!

  I'll let you know...

  Mike

• "Access: Local only" problem and an unidentified router connection.

  I use a laptop Compaq Presario CQ60 with Windows Vista Home Basic.

  The laptop connects to the router (a Belkin.43A1) However, it is unable to correctly identify the router and does not connect to the internet. Offer me only a "Local" access only

  My brother has the same exact model of the laptop and windows vista edition, with all settings completely unchanged but suffers still from the same connection problem.

  All other devices in the House are able to connect to the internet through the router, such as ipods and game consoles. Another laptop running Windows XP is able to connect without a problem.

  Connecting the laptop to the internet works when connected via an ethernet cable.

  I tried several solutions offered on the internet without any positive results, such as:

  -Disable IPv6

  -Computers wireless card uninstalled, then put it back

  -Uncheck the link layer topology

  -Restart the router/mobile

  -Check and install all updates for windows and HP

  And several others, all parameters have returned to what they once were.

  Help and suggestions or solutions would be greatly appreciated thanks.

  Hello

  It could be set-match security, log in to the router wireless security turned off and see if you can connect

  If it works, restore security.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• No Internet access - network/router wireless connection problem

  I can't connect to the internet after installing Windows 7 64 bit. I can see the router wireless/network from my computer, but it has sometimes limited connectivity or it says connected but no internet access. I used Windows diagnostic tools to try to fix it but it does not work, and my router connects without a doubt to the internet such that I now use on a portable computer that is on the same network. I would like to know if anyone else has this problem and if they fixed. I tried to change the physical address of the connection to the local network, but it didn't work, I guess because I connect via radio and no cable, and I heard similar stories on other forums that this can be a problem more common I suspect. Thanks in advance for your answer, and all the details you need I'll try my best to provide.

  OK I finally got to work, all we needed was for me to download the latest drivers (Realtek 8185 wireless card) off-site and install in compatibility mode, and then he worked all of a sudden. I hope this will help someone suffering from a similar problem!

• Strange internet connectivity problem

  Hello!

  I'm having a connectivity problem I have never met before. I use a wireless router from Apple with internet cable.

  Yesterday, my computer would be is no longer in contact with my router wi - fi. I get a message that the network could not be attached (I ran the Diagnostics wireless, but it's a whole lot of sense to me empty files). However, I also have a Roku, and which IS connected to the WiFi without problem. I completely stopped and restarted the computer, no joy. Reset the modem and the router, no joy. Still works with Roku, not with the computer. But the weird part is, I have Optimum Online, which allows subscribers to log-in to its hotspots, and it worked! I am connected Optimum wi - fi network on my computer right now.

  So I don't know where is the problem! It is not the router, because this is related work with Roku and is not the computer, because it is connected and working with the Optimum hotspot. What gives?

  Try this!

  Go to the Apple menu > System Preferences > network

  Select a Wi - Fi connection in the sidebar and then click on the button "Advanced...". "in the lower right corner of the screen

  In the list of preferred networks, delete the name of your Wi - Fi network

  Click on the "OK" button to save that change and then 'apply' in the network preferences window.

  Now, go to the Applications folder > utilities > Keychain Access

  Make sure that "Login" keychain is selected and "All items" in the category is selected in the sidebar

  Use the search field to find items that Keychain with the name of your Wi - Fi network and remove

  Quit Keychain Access

  Now try and access your Wi - Fi network

• Officejet 4500g510g connection problem

  The printer constantly alternates of connected and disconnected as displayed on the HP Solution Center does not allow me to fax or scan but allows me to print

  Hello VinhLong,

  When you connect a device to a router router assigns the device an IP address. There are two types of these assignments. You have a dynamic IP or static IP address.

  A dynamic IP address can change and is automatically assigned by the router. Whenever you reboot your computer, printer, etc., the router can assign the unit a new IP if for some reason he can't use it. This is the default setting and is what most people use.

  An IP address is an address that you essentially hard-code in the router which tells the router whenever this device connects to the network assign this IP address. Using the static IP address performance and connectivity is generally improved.

  Since you have a connection problem, we should see if we can stabilize the connection hard coding a static IP address on the router and the printer to the printer to use when connected to the router.

  Information about setting up a static IP address were taken from this article for troubleshooting HP.

  The "Printer not found" error message during the Installation of wired (Ethernet) network in Windows XP and Windows Vista

  The article is not completely relate to your problem, but we use it to capture the static IP address instructions.

  The DHCP Dynamic Host Configuration Protocol () service provided by the router can change the Internet Protocol (IP) address on the HP product, which interferes with the network installation. An IP address uniquely identifies the product over the network.

  Follow these steps to assign an IP address does not change to the product by the built-in webserver (EWS).

• Satellite L100 - connection problems with a wireless internet connection

  Hello

  I had some of my Satellite L100 connection problems to my sky wireless broadband connection. My laptop detects the connection and I have a bubble appears confirming that the wireless connection is connected. However, when I open internet explore it appears with 'cannot display the page'.

  Now, the wireless works with our other non-Toshiba laptop so I know that the connection is ok but it does not connect with my Satellite. Is there something I can do?

  Try reboot you the router. In many similar situations, it helps me.

• Iconia A1-830 has a Wifi connection problem when 3-5 meters

  I bought Asher Iconia A1-830 at BestBuy and after 10 days, I discovered the Wifi connection problem. If you stay near router (1-3 meters) the WiFi signal is good (not excellent). If I go into another room - Wifi connection is poor or disabled. I changed it to another (same model). The second model is perfect only 1.5 months and now she has the same problem with wifi connection. Can someone help me? Maybe the problem in my router, but why it worked 1.5 months?

  Yesterday, I received my return of repair Acer Iconia. They wrote the reason of the problem: reconnected hold of WiFi to the motherboard. It now works like new!

• Two wifi routers EA6200 having connection problems.

  I had a single wifi router configuration EA6200 and it was working fine but it has not reached the corner of my house. I decided to buy a second EA6200 in an attempt to expand coverage wifi and nothing else that problems have had since then. I tried several configurations and there are always questions where wifi is either very slow or cut all together. I tried to configure the routers by using the options listed in the manual. We'll call it the router connected directly to the modem ROUTER1 and ROUTER2 upstairs router.

  I connect both routers via a power adapter line I used for a while since I rent and can't pass the cables through the walls. I have one of the LAN ports on ROUTER1 connected to port WAN on ROUTER2 and ROUTER2 clipping value. I tried with ROUTER2 get his address IP of ROUTER1 automatically and I also tried to set a static IP address on ROUTER2, but I always had connection problems. I also tried one of the LAN ports on ROUTER1 connecting to one of the LAN on ROUTER2 ports. I put a static IP address on ROUTER2 and disabled DHCP. For both configurations, I tried to have the same SSID and password for both routers so that I can roam and connect automatically to the strongest signal and at first I put the automatic channel selection. I still had problems connecting so I tried to change the SSID of the router and change the SSID for the bands of 2.4 and 5 GHz and I tried to adjust the channels myself no conflicting channels and I still have problems.

  Again, the problems I encounter are failure intermittent wifi where it disconnected completely from the wifi but will reconnect then slow connection speeds not long after but also intermittent. Also, I have several chromecast dongles on the TVs in my house and they also periodically lose the connection to the network and have a lot of buffering issues. These problems disappear with a single connected router. I also tried to reset both routers and disconnect and plug my modem at the factory.

  All the ideas, because I don't see anything else to try?

  Bilz says:

  If I understand you correctly I tried already. I connected the LAN to LAN and used the static IP you listed for the second router. I put the SSID for the 5 GHz band were the same for both routers and used a different SSID for 2.4 GHz bands, but it's still the same on both routers. I used the Wifi Analyzer app to determine the best channels for my router and I put them all channels different worms. I don't know if I used specifically 1, 6 or 11, however. It would make a difference? For example if I used chanells 4 and 6 for 2.4 GHz bands, do you think that this would have caused some of my questions?

  Not quite. All SSIDs 4 must be different. You can be the cause of the camera jump back using the same ssid. So it could be xxxxx_24p and xxxxx_24s and even for the 5 GHz. xxxxx_5p and xxxxx_5s