Satellite Pro A10 stops after 15 minutes of internet games

Similar Questions

• Satellite Pro 6100 stops after 15-30 minutes

  My satellite Pro 6100 Cup after 15 to 30 minutes of operation on power outlet. There is a noise and all the lights go out except orange slow flashing (power problem). I have restore by removing the power cable and wait a while.

  It will then start again. I used two different adapters and two different batteries. It also happens if work on AC with no battery in the. My suspicion is an overheat cut-out. The Sat Pro has a? Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in. Advice much appreciated. Thank you.

  > Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in
  I agree with you and the user SambadeAmigo. It seems like a simple problem of overheating and so the laptop automatically stops to prevent the equipment from damage

  I assume that your laptop can be enabled again after being allowed to cool. It is a common question if the cooling modules may not work properly because of the dust and debris.
  As suggested, it would be possible to remove dust using the can of compressed air.
  It should work.

  See you soon

• Satellite A10 stops after 40 minutes

  A-10 Pro keeps closing after 40 minutes, power source is always the head of HQ, can anyone help?

  Has been verified the following: -.
  Virus
  Management - never switch on stop
  Cooling fan seems to agree

  In my view, this question has nothing to do with the virus, but maybe with overheating.
  How old is your laptop?
  Have you ever cleaned cooling grids or cooling fans? Fan may be OK, but how it looks behind the grille. Perhaps there dust and traffic blocks the air properly.

• Satellite Pro A10 stops on specific opportunities

  Hello!

  I am owner of a satellite Pro A10 (PSA15E). It's hard drive stop working, the pc could not find. So I bought a new, a samsung with 160 GB, IDE, of course.

  Now when I was installing windows, in the part file copy, it just stopped. When I boot it says initialization file fails, then I guess it stops when it was to transfer this important part.

  If I run the cd again, it does not format or reinstall/repair request, it loads only some files and try to start windows and then stops.

  Now, this is where the tricky part comes in: the power led in turn, then again very fast when it stops. I do not use the battery (it is already dead too), and I use an universal AC, a give, 70W adapter. I tried formatting via a LiveCD Ubuntu, with no luck, because when I choose "Try Ubuntu" or "Install Ubuntu" it stops a little as he thought, and then when he is about to leave the menu and do something, it stops in place.

  My only guess, is that this laptop doesn't want me more :(

  I could really use some help, I just spent some 50 on a HARD drive for him and he is the only laptop that I have. I don't think that it is a question of temperature because it stops just at specific times, on some specific choices. If I just let it hang there in the menu (the Ubuntu live CD one) it is not closed. Only when I want him to go further.

  Any help/response is greatly appreciated, and if I take a little too much time to respond is because I don't have access to internet at work now.

  Thank you very much
  Ricardo Rebelo

  Hello

  Theoretically, this could be an overheating problem as Akuma wrote. Therefore, you must clean your laptop using a jet of compressed air. This could blow the dust from the cooling fans and can improve the cooling of the laptop.

  In addition, it would be interesting to know what happens if you run Toshiba Recovery disk recovery facility this work?

• Satellite Pro A10 stops during the installation of Windows

  I have a satellite Pro A10, which stops during the installation of Windows. The installation gets to the part where I need to select the HARD drive to install, then the system off just. I can restart it immediately, and the sdame happens.

  If I enter the BIOS, everything is detected OK, and I've updated to the latest version (V1.4). Also when in the BIOS, the system will remain under tension for ever and a day! and no downtime. I have a couple of diagnostic CD, then run the tests is the same thing, but I ran the seagate diagnostic tool and the HDD OK passes, as does the main map, but cannot perform detailed testing that the system shuts down during the tests.

  I suspect an overheating issue but would like advice.

  Hmmm it s very strange. I thought that the HARD drive could malfunctions but it of very impossible if the HARD drive has passed the Seagate diagnostic test.

  However, it would be very interesting to know if the installation of the OS would end with another HARD drive.
  You know, it of always difficult to provide an exact solution without any diagnostic tests.

  For me, it really looks like a hardware malfunction. So perhaps it would be advisable to contact the authorized Toshiba maintainer for a control of the laptop.
  Guys could run tests and would situate the fault quickly.

• Satellite A30 921 stops after 10 minutes

  I am the owner of a Satellite A30 921, but it stops after 10 minutes.
  I tried to change the settings for toshiba power management, but they will not work any ideas?

  The laptop turns off automatically without display of error messages?
  This can be caused by an overheating problem!

  How old is your laptop and you clean the cooling fans in the past?
  If this isn't the case, I recommend you this doing.

  To clean the fans, you can use the jet of compressed air that can be bought in most computer stores.
  The problem is that dust and debris inside of the laptop prevents cooling modules works properly, and so the temperature increases to a higher level. This leads to the farm automatically from the bottom.

  In my opinion, fans of cleaning might help with this problem.
  Good bye

• Satellite A100-914 - stop after 10 minutes on

  Satellite A100-914 - Vista Home 32-bit edition

  For some time, whenever I turn on the computer it off after 10 minutes. Usually I restarted and then everything was ok, but these days, it seems to stop several times.

  In my screen displays the blue screen saying on: driver_power_state_failure...

  I've updated to Vista, a patch which should solve this problem, but the problem of still images.

  I have also updated the Bios of Toshiba, and then I get a Warner 0251 checksum bad - default configuration used.

  I also have problems with superfetch and search for host when I connect to the internet... but it is perhaps another question...

  Thanks in advance
  Daniel

  Hello

  What to say...

  Regarding the automatically close downs;
  For me, it looks a bit like overheating. Maybe you should check if the temperature is not too high and check if the cooling modules are working properly and it can cool the laptop properly. Sometimes the dust inside the laptop could have a bad influence on cooling.

  Regarding the system BIOS checksum bad - default configuration used:
  Try to access the BIOS and set the default BIOS settings. Then save the changes and restart the laptop.

  Regarding the MS patch:
  I found this Microsoft Knowledgebase document:
  The STOP Error Messages troubleshooting 0x0000009F DRIVER_POWER_STATE_FAILURE in Windows
  http://support.Microsoft.com/kb/246243

  It is said that this problem occurs when drivers do not properly handle power state transition requests.
  The error message most often occurs during one of the following actions:
  -Closing
  -Suspension or out of standby mode
  -Suspension or out of hibernation

  Check solution proposals in the document of Microsoft.
  If this does not help, I guess it's a hardware problem and you will need to contact the ASP in your country.

  Good luck

• Satellite C660-1ZN stops after 30 minutes

  I just recently brought a portable c660-1zn but it overheats and turns off after about 30 minutes when I play games like second life on the graphics settings lower.

  I know that's not it's a new laptop from dust. Should we do this? or is it current on these laptops
  more his game to power saving in power management and am making sure that the ventilation is not covered.

  > I know is not that it is a new laptop from dust. Should we do this?

  Laptop overheating not even if some strong performance running applications or everything at stake.
  You use the preinstalled Toshiba system?

  You should test the laptop with system preinstalled Toshiba and published by Toshiba display driver.
  The driver can be downloaded from the European pilot of Toshiba page!

  Remember that this driver is already installed, because this driver supports the GPU overheating protection. This keeps the temperature low and decrease the performance if the temperature rises.

  This is necessary because the laptop cooling modules are smaller than the cooling modules in desktop computers.

• Satellite Pro A10 - unable to connect to the internet

  I have an old Satellite SPA10 who lost the internet connection a year ago.
  The components in question are:
  Ethernet controller
  Network controller
  Video controller
  Video controller (VGA)
  I tried many attempts to install drivers to replace those already on, but each attempt failed. Toshiba downloads, I used were from the following link:
  NES http://www.Toshiba.co.uk/innovation/download_drivers_bios.jsp?service=UK&mode=allMachi & action = sea...
  I use a desktop computer that is ok, although it has its own flaws and want to return to the use of the Satellite.

  Any suggestions please?
  (With the help of Windows XP)

  Hello

  This old model of laptop is supported for Windows XP Home edition and Windows XP Home edition is not supported by Microsoft more.
  In any case if you want to have good working machine I recommend to do clean install of Windows XP Home edition.
  After doing this you also install all the necessary drivers and tools and utilities.

  This laptop model was offered with Windows XP Home SP1 edition at this time.
  You have Windows XP Home edition installation disc? Is the new installation of Windows XP Home edition an option for you?

  If so, I can help you with this and send you the order of installation exact for the drivers, tools and utilities.

  One last thing: you have the original installation of recovery disc?

• Satellite Pro U200 starts after some time it stops after 5 minutes

  Satellite Pro U200 stops after 5 minutes, then starts after some time. When she stops the
  blue screen say - stop: (0x0000008e, 0xaa846f58, 0xa9f29808, 0x00000000)

  Sysaudio.sys - address aa846f58 base at aa843000, datestamp 41107f1a

  Hello

  Believe me; It's not easy to say exactly why the BSOD appears.
  It usually happens because of a malfunction or severe software hardware fault.
  Have you used the operating system of the image of Toshiba?
  Message it says something about sysaudio.sys.
  This file is a system audio WDM filter processes and it s a part of the Windows operating system. It controls the material such as the printer or the graphics card at a lower level.

  Note: The virus uses these files as a camouflage. You should always use an anti virus application.

  In addition, you suggested that the laptop stops after 5 min.
  Well, this looks like an overheating problem. How did you use the laptop? You know that free space around the laptop is very important due to the circulation of air. Fans should also be free.

  I you use Notepad in the right position and it happen, so I recommend asking for help Toshiba service partner. They should check the laptop.

• Satellite Pro A10: Extraction failure error occurs during my recovery procedure

  Im trying to run recovery disks on my Satellite Pro A10 but after 20 seconds trying to install recovery disc 1 gose black screen and message in corner says extraction failed.

  Can you help me please?

  Have you tried to format and delete partitions on HARD drive integers before performing the installation from the recovery CD?

  Something similar happened to me. I wasn't able to install the OS from the recovery CD.
  I simply used the original Windows CD and you have formatted the whole HARD drive.
  After this procedure the recovery CD installation worked a lot.

• Satellite Pro A10 CD Burning: after having burned the CD is empty

  Hello

  I have a Satellite Pro A10 and my CD burner stopped burning. Someone at - it? I also had a problem earlier where he would burn only 1 disc immediately after startup. It says it burns and goes through all the motions, but in the end the drive has nothing about it. I use Maxell discs and have had no problem before using these. If the CD burner is broken it is possible to get a replacement and they are also easy to assemble.

  Thank you

  Hello

  It is really possible that the drive is defective. Before Exchange you it the only thing, you can try is to check if there is some success if you use different empty media (producers) and burn it using a few different burning applications. I recommend you to use NERO software of engraving.

  Also be sure that the engraving option is enabled and not only option called simulation.

  Replacement should not be problematic. If I remember correctly from the drive is fixed with a screw and you can find it in the bottom corner near the drive itself.

• Satellite Pro A10 PSA15E: NO sound after installing Win XP

  Hello world

  I had to reinstall Win XP Home - which went well, however - now there is no sound and it says no audio device is installed. I tried to install the audio drivers on the Toshiba CD but they go as far as unpacking but then say "not installed" and Setup stops.

  I went to www. support. Toshiba.com and follow the menu to identify which drivers to download? but there are several possibilities for the
  Model A - 10 and I am not sure I have listed below models have.
  A10-S100, A10-S1001, A10-S127, A10-S128, A10-S129, A10-S1291, A10-S167, A10-S169, A10-S1691, A10 S177, A10-S178.

  I would be grateful for your advice.

  Thank you

  Andrew

  @mrafowler

  > I went to www. support. Toshiba.com and followed the menu in order to identify which drivers to download, but there are several possibilities for model A-10

  What you mean? On the European driver Toshiba page, you will find only one series Satellite Pro A10.
  Once again; Do you have a computer or a Sat Pro A10 laptop satellite A10?

  There is a driver of sound for a portable Pro A10. This is a version of audio driver Analog Devices 5.12.01.3542.
  If you are using XP SP2 please check the information provided on the page of the driver Tosh

• Satellite Pro A10 does not pass the Windows page after removing SP2

  Hello

  I have a toshiba laptop Satellite Pro A10.
  I installed windows service pack 2 week last to try to get one of these dongles TNT to work, he never so I uninstalled service pack 2 I was going to try and reinstall it to see if it would work.

  Now, my problem is that the laptop will not go at all, it gets to the windows XP page and then everything stops, someone could help me I don't know what to do!

  Thank you
  Sharon

  Hi Sharon

  Seems that the system files are corrupted on the HARD drive.
  All of the installation and the removal of the service pack has damaged some files or registry entries.

  I don t think you will be able to resolve this situation without reinstalling the OS.
  In my opinion, it's a better way to get rid of this problem.

  Take the Toshiba Recovery CD and reinstall everything.
  If you want to back up your data, I recommend to connect the internal HARD drive to another computer via the external USB HDD controller.

  Good luck

• Satellite Pro A10: No sound after upgrade to Windows XP Home SP2

  Hello

  Just use the recovery disks on my Satellite Pro A10, no problem with the sound, and then upgraded to XP Home with SP2, no noise.

  What I've read elsewhere, this is a problem and there seems to be an answer. I spent hours looking for drivers updated without success.

  I have also contacted Toshiba support, after blow and blow that they reported the following driver, 5.12.01.3542, which is the same one that I have already installed and does not work.

  Certainly there must be something out there that works.

  Ant.

  Install the driver of his most recent available FRO this sound chip and perform all the Windows updates available on the Microsoft page!

  Update just the BONES together!
  http://www.update.Microsoft.com/microsoftupdate/v6/default.aspx?ln=en-us

  Notes; You may have to restart the laptop and need to connect to this site several times to get all available patches.