service.msc overrides msconfig active service?

Similar Questions

• MSCS on an active DRS Cluster HA?

  Hi all

  We are setting up a 6 host DRS activated cluster HA with a host as the host of the previous day. Two of our virtual machines will run MSCS cluster (with active and passive node). What we want is that:

  1 - Normal VM must be restarted on a host sleep by using cluster HA when an ESX fails.

  2 VM Normal should be vMotioned DRS decides.

  3 clusterises MSCS VM should restart on a host sleep by using cluster HA when an ESX fails.

  4 MSCS group of VM should not be vMotioned automatically. Must reside on the specific host.

  Are higher than 4 point if possible please confirm how we do. I'm a little confused that as per below document MSCS is not supported on active DRS cluster.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1037959

  Kind regards

  Khurram Shahzad

  According to the doc of vmware, the installation program for the Clustering failover and Microsoft Cluster Service to Vsphere5 no problem when you use the DRS and HA together. but it takes only

  1 - two nodes must never operate in a single host for HA and DRS
  2. to do this you must create the rules below

  -HA, create a host of DRS group, and then create a group of Virtual Machine DRS, then A VM host affinity rule must be created, with a group of virtual machine DRS and a host of the DRS group.
  -DRS, create anti - affinity machine VM-virtual rules specify which virtual machines should be stored on different physical hosts and turn on strict application of the law of affinity rules virtual machine configuration

  Or you can also disable the DRS for these 2 nodes and enable only HA, but even once you must ensure for HA 2 nodes never operate in an ESXi host

  See books of installation for Failover Clustering and the Microsoft Cluster Service to Vsphere5 and vsphere-esxi-vcenter-server-501-resource-management-guide

• How does influence Services.MSC Msconfig.exe?

  How does influence Services.MSC Msconfig.exe?

  .. a small example to better understand my question: p
  Why when in Service.msc, I disabled Acrobat Update Service (for example), the service in Msconfig.exe still is checked in the service menu?
  It is marked as stopped however.
  Service process uncheck = unchecking in Services.MSC in Msconfig.exe?
  Reboot was done of course.
  Thanks, please help!

  The result would be the same.  The best practice would be to use the disable services continuously, change the startup type, or start services and Services using MsConfig just for troubleshooting.

  To see what is happening in real time, life is to try MsConfig and Services, including all necessary reboots etc (if you wish).

  Services can be affected through the registry too.  There are often several ways of doing things in Windows to get the same result.

• ExceptionHandler implementation and activity marked as 'exception handler.

  Hello
  
  Please consider this sample application created using JDeveloper 11.1.1.3.0
  at http://www.consideringred.com/files/oracle/2010/CombinedExceptionHandlerApp-v0.01.zip
  
  It has an implementation of the ExceptionHandler configured in a services configuration file and config file adfc. XML that unbound the task path has a view activity "exceptionHandlerPage" marked as "exception handler.
  
  -scenario (sc1)
  Run the page browseDepartments.jspx and click on the button 'make throwMyViewRuntimeExceptionAction', resulting in a dialog box showing a FacesMessage created in MyViewExceptionHandler.handleException (), as shown in the screenshot CEHApp-001-sc1 - dialog.png.
  
  -scenario (sc2)
  Change the contents of the «.adf\META-INF\services\oracle.adf.view.rich.context.ExceptionHandler file"in a class name unknown, for example,"MyViewExceptionHandler"to"UnknownMyViewExceptionHandler ". (causing a java.lang.ClassNotFoundException when execution and application of ExceptionHandler therefore actually not custom configured)
  Run the page browseDepartments.jspx and click on the button 'make throwMyViewRuntimeExceptionAction', with the 'exceptionHandlerPage', showing the result of the EL expression result #{controllerContext.currentViewPort.exceptionData}, as shown in the screenshot CEHApp-001-sc2 - page.png.
  
  Based on the scenario (sc1) and (sc2), it looks like an implementation of the ExceptionHandler configured in a configuration file of services takes precedence over an activity in the boundless task marked as '' Manager exceptions '' flow.
  
  question:
  -(q1) is it expected behavior that an implementation of the ExceptionHandler configured in a services configuration file overrides an activity in the stream of boundless task marked as 'exception handler?
  
  Thank you very much
  Jan Vervecken

  Jan,

  Yes. Actually, the exception handler is called instead of the default AdfcExceptionHandler, which is the implementation that makes the activity of the labour exception handler. If you handle an exception in your custom exception handler class, up the machine again and the default mechanism is used.

  Frank
  PS. : If we woul do the opposite so you won't be able to change the behavior of management at all ;-) exceptions

• Problem of recovery of TOSHIBA NB550D-111 due to the error of the stormwater management

  I own a NB550D-111 (pre-installed W7 Starter 32-bit SP1, av Security Essentials), used mainly for navigation, chat and Skype. After the updates of July, BONE began to greeting me with blue screen every startup. I chose "Startup Repair", and after twenty minutes and a reboot, the operating system was running. On the next reboot, the same scenario. Whenever I ran "Startup Repair", sometimes 3 or 4 times to get the system working.
  I did a system restore, but no luck. Still the same blue screen at startup. I ran past check disk at startup of the prompt and/f/r, no error found. After four days, the startup repair couldn't solve the blue screen, although I spent almost 4 hours of restarting and either Startup Repair choose or do the system restore.
  I went to Restore Factory Settings OS since the recovery partition. I wanted to keep the My Documents folder, I changed the location of the second partition). ImageX gave an error to 70% in application of the image (a .ttc file that cannot be copied), and after that restart BOOTMGR is missing. I used the recovery usb key made shortly after I bought the netbook via Toshiba Recovery Media Creator, wich wiped clean the HARD disk (possibly lost my files, she), re-partitioned and copied the .swm files into the folder HDDRecovery. When you apply the C: partition image, Imagex also gave an error at 70%, the same ttc file.
  I installed a clean copy of starter, installed SP1 and updates and activated online using the serial number of the COA sticker. Initially, the newly installed operating system was incredibly fast (I only have drivers and card Flash not installed, no other application from Toshiba), but after SP1 update start time three times. My previous experiences with Windows XP, an integrated installation of Windows SP behaves better than an update with windows update. I think of a way to reinstall the Toshiba Windows, still full of bloatware as it is, then stop the programs that I don't use services.msc and msconfig hollow (just like I did when I bought the netbook).

  Post edited by: bogdanmardare

  I thank very you much for your detailed job offers.

• Windows Update not working do not Error Message and Windows Defender cannot update Error Message definitions

  I have a laptop Dell 1501 with Vista Home Basic 32-bit.

  I ran CA 2010 Security Suite and you have scanned for Malware with regard to the Windows Update Error Message. He found none. I ran Microsoft Malware malicious tool, and it found. I ran Windows Defender and he found. I don't have CA and Windows Firewall to protect my computer and I have disabled both in trying to solve this problem of Windows Update and Windows Defender.

  I got this error 4 days ago. Here is what I tried:

  -I went on various Web sites, including Microsoft Support - and tried to solve the problem through services.msc and msconfig.exe. None worked.

  -J' noticed in msconfig. where it says start waiting next to Windows Update. There are 3-4 elements, which are affiliated to Windows Update and made sure they did not exist in the registry.

  -J' have to ensure that they were supposed to be automatic or manual under services.msc.

  -J' rebooted several times and nothing changes.

  Windows Defender does not update the definitions, and I do not know if this coincides with the release of Windows does not.

  I am at my wit's end and do not want to crash and burn my computer.

  I need serious help. Please, I beg you!

  Thank you.

  LRR100

  I had to call Microsoft. Alex tried to add registry keys and input upgrade.

  My Windows Update has almost been altered. It could be my mistake or it has become corrupted when running other services at the same time.

  I was sent a Windows 7 Home Premium Disc to upgrade and start over, as my Vista disk was corrupted as well.

  I would not recommend trying one of the suggestions listed on other sites. It's my personal opinion because I have in the past and it worsened my problem.

  I also wouldn't delete all programs (unless absolutely necessary) because I remove 4 MSMXL and he made their work more difficult.

  ________________________________________________________________________________________________________________________________

  Sometimes the only solution is to call Microsoft and they will evaluate if a charge of telephone support is necessary from the outset, before they run for your problem.

  Despite what you may have read, Microsoft Technical Support technicians are very efficient and kind.

  We inform you to open a slot during your day or even open your day for the problem to be solved.

  Mine took 2 1/2 hours, and they had to remind me the next day to make the order for the disk because it could not be done the same day.

  The more patient and kind you are, the best representative.

  Hope this helps and thanks for reading,.

  LRR100

• What is ntuser.dat.LOG1 file under users > by default

  I have a USER. 1Ko DAT file; I also have a ntuser.dat.Log1 of 45KO files. and an another ntuser.dat.Log2 1 file KB.

  I think I could have done something to change the configuration of the way in which services are started to make the 45KO file.  Is this necessary?  Can I delete it?

  These files are under users > default

  These files are normal.    To hide, go to Control Panel > Folder Options > view and select do not show hidden files, folders, .

  I mentioned services.msc and msconfig because I thought that the original poster was asking how to set up the way the services are started.  They have nothing to do with the files that you see. Steve Winograd, Microsoft MVP (Windows desktop experience)

• Print spooler continues to falter in win7

  I had problems with my network printer HP1022n since installing win7 home premium.  The printer works just find with my XP boxes, so it is not a hardware problem.  HP finally came out and said that they do not have a compatible printer driver for win7 network again, I try to uninstall the printer and try to install a new driver for a local (USB) connection.  The problem is, I can't uninstall the device from the spooler continues to falter.  I try to disassemble the camera, but the printer will not go away.  I check what is in the queue, and I get the error:

  Operation could not be completed (error 0x000006ba).  The local print spooler service is not running.  Please restart the spooler or restart the machine.

  I guess that's why I can't delete the device.  Restarting the computer does nothing and when I try to restart the spooler manually with services.msc it remains active for a few minutes, but the second I try to do anything with the printer (like trying to remove it) the spooler dies again.  He dies also after 3-5 minutes when I do not do anything, but I can certainly kill him watching as long as the printer.  Any ideas on what to do?  Thanks in advance for your help.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• "OS Partitions" option when you build a new PowerEdge

  It's been a while since I ordered a new EP, and I'm a bit confused about this "OS Partitions" option. I'm going with a 4 drive RAID 10 (500 GB disks) and Windows Server 2012 Standard. The selections available are:

  • None
  • 40GB Microsoft OS Partition Override
  • 80GB Microsoft OS Partition Override
  • Maximum Microsoft OS Partition Override, GPT active
  • Override size maximum partition for Microsoft Windows factory installed

  I called Dell and did the cat online and not had a clue what meant these options. I found some old discussions on the subject, but none were really difinitive on how the server would be configured according to each option. The 40 and 80 GB are pretty simple, although same 80 GB seems a little low these days especially with most of the servers with 16 GB + memory (swap), so it would be nice if you could choose a custom size.

  Then, how the server will come to set up if I select "None"? And what of these two options 'Maximum '?

  I think that few people know what 'no' means here, because they are more likely to choose one of the other options.

  None: this could just be the minimum score allowed by Windows (32 GB) size. Or (less likely), it could just be that Dell includes support of OS but no factory of the operating system installation.

  40 GB Microsoft OS Partition Override: Simple. Probably too little to be viable for MOST uses, but if you know what you are doing and the need to rationalize the C: partition, then maybe it's not a big deal (the filename of the page could be moved to another "disc" as well). I have an installation of 2012 who was sitting at about 35 GB since December (including 8 GB page file) - it is not a widely used server, running in the form of DC and the WDS server (of course the images are stored on a 'second' disc).

  80 GB Microsoft OS Partition Override: once again, simple. I would deploy a server with a disk of 80 Go C:? No, I would give it at least 100 GB (depending on what it is for, that I use usually about 120 GB). However, 80GB - if you were stuck with it - would probably manageable (if you can move extremely large page files to another drive).

  Maximum size of Partition override for Microsoft Windows factory installed: this will create a C: partition encompassing the entire size of the 'drive '.  If you have a RAID 10 4x500GB, with about 1 TB of usable disk space, then your C: partition is 1 TB.  This works for any configuration of "drive" up to 2 TB, which explains why the GPT option is available.

  Maximum Microsoft OS Partition Override, GPT active: say you have a RAID 10 4x2TB, which gives you about 4 TB of usable disk space. So that Windows to see and use a "drive" that big, it must first be converted to the GPT. However, Windows can only start a 'disc' TPG if UEFI is supported and enabled on the system. Would you then a partition C: from 4 TB... I'm not 100% sure that's how he'd come, but according to their description, it would be my guess.

  Personally, I would choose the 80 GB partition. With 2008 and later versions, it is EASY to extend, retractable partitions in the diskpart/records management, so I get it to 80 GB, and then extend to 120 GB or anything else that seemed appropriate for the installation of the server.

• I can't activate Acrobat in CS6

  I just reinstalled CS6 on a new PC. I entered the serial number, and Photoshop is OK. However, when I run Acrobat I get the screen that says 'Design and Web Premium Trial', you can try this product for 7 days.
  After I click on "license this software" I get "Sign In required" and he said: ' we will sign you like Adobe ID: myID. I then click on connection and I get 'Thank You' but after I click on continue or if I close the window

  I need back window 'Design and Web Premium Trial'.

  How can I activate Acrobat, please?

  I am using Windows 7 64 bit with 16 GB of RAM

  Dejan

  Hi dekiblue,

  I checked that you have an active subscription to creative cloud. Thus, every time you sign in with your Adobe ID, Creative Cloud overrides the activation of all products CS6, but not Acrobat X because he isn't a part of the creative cloud.

  You can use Adobe Acrobat Pro DC using CC on this machine and it works fine. In the case where you would like to use Acrobat X please check workaround mentioned in:

  • License considerations mixed - if you have an active member of the creative cloud and a serial number for Lightroom 6

• Brush Tip shape

  Under brush tip shapes, the 'Dynamic form' option does not turn off even after that I have untick the option of turning it on. When I try to paint, "Shape Dynamics" continues to restart automatically as soon as I apply the Brush tool. How to stop brush tip shape "Dynamic shape" to be extinct? Is this a bug or is at - it another way to disable it? I use PsCS6. The second image shows how, even when I turn off the coast, the dynamics of the form is still touching the tip of the brush.

  

  If you use a drawing tablet, you override pressure activated in the options toolbar?

  

• Msconfig vs services.msc in win7

  I was then trying to decide if I should use config to control my start-up, start-up deactivation etc, or is it better to use services.msc? What's the difference/consequences of both.

  Any thoughts greatly appreciated.

  Ken

  Services.msc may only provide the access to the services. However, MSCONFIG gives you access to programs from startup, boot options and services also. I suggest that use you MSCONFIG to control your desktop.
  Here is a link that gives you detailed explanations on the MSCONFIG tool and its use:
  http://netsquirrel.com/Msconfig/index.html

• "services.msc" shows almost all disabled services. Who should be activated?

  Could not connect online.  Said to check microsoft for answers.  They said come on in 'services.msc' and turn on plug-and-play.  When I went I noticed that almost all of the services have been disabled and I don't know which ones to activate.  Can you help me?  Thank you e advan

  Viper black Windows XP Edition family and Professional Service Pack 3 Service Configurations

  The link above provides the name of the service with the default setting and what services are safe disable or change.

  For facilities more typical, many services are configured as "automatic", which means they will automatically launch at startup of Windows or when the service is called for the first time.

• Unable to connect WiFi: Services.msc maybe?

  I use several wireless receivers.  A PCI card and 3 Wireless USB devices.  Just bought a brand new Netgear N300 yesterday.  The modem is a type of Belkin N.  I can connect on a laptop that is about 3 years old, but not on my desktop.  I think there is something in Services.msc that blocks the WiFi because I have disabled or placed in many manual settings which were not necessary for optimal performance.  I have the usual stuff to automatic configuration wireless, CPP, etc..  I was wondering if there is anything that might be the problem.

  Just diagnosed with the Netgear software and the Ipconfig command.  They both say "Media disconnected" again the USB Wifi adapter is plugged in and sees the router.  Anyone know what "Media disconnected" means?

  First of all, I apologize if my previous answer seemed a bit snippy.

  You live dangerously with no. a / v.

  Your conclusion that it is not the router because everyone can connect is not necessarily correct.  You could still have an incorrect wifi encryption configuration - or this router is completely secure (not need a password to connect)?  What level does the router encryption have established?

  Assuming that you are really sure that you have the correct password (or it is not a), I suppose it is possible that in tweaking things you disabled some (I can't think) service that is required.  Take a look at the site of the Black Viper (link in the previous answer) and compare your list of the services disabled to set up "Safe."  Check the descriptions of all the services that you have disabled which helped Black Viper in its 'Safe' configuration

  You can also take a look at the event viewer (start > run > eventvwr > OK) and see if there are clues here.

  "Media disconnected" for a wireless network adapter that shows the router in the list of available wireless networks almost always means an authentication problem... and almost always he turns an incorrect encryption password.

  Just to be great depth...

  • Make a right-click on the icon of any wireless adapter is active and select Properties.  You should see a screen like this--> http://screenshots.modemhelp.net/screenshots/Windows_XP/Network_Connections/Wireless_Network_Connection/Properties/General/Index--2.shtml
  • Click the "Wireless networks" tab and you should see something like this-->http://screenshots.modemhelp.net/screenshots/Windows_XP/Network_Connections/Wireless_Network_Connection/Properties/Wireless_Networks/Index.shtml

    On the tab 'wireless networks:

    -is the box "Use Windows to configure my wireless network" verified or unverified?
    -is the SSID (network name) of the router listed under "preferred networks"?
    -If the SSID of the router is listed, it is a unique name, or is it a default value (for example, "Linksys")?
    -If the SSID is listed, a common method of "starting over" is to «remove "the entry;» OK your way your computer; and then try to connect to the network; all information configuration 'wrong' that has been repeatedly used will have been removed
    -Select the SSID of your router and click on "Properties".

    In the tab "Association":
    -What's in the box "network authentication"?
    -What is in the box of "encryption"?
    -is "the key is provided for me automatically" verified or unverified?

    Under the tab "authentication."
    -is the "Enable IEEE 802. 1 x authentication for this network"checked or unchecked?

• Terminal Server service not activated

  I downloaded McAfee total protection in October.  It would work for a day or two, then I get a message that wouldn't update.  I have uninstalled & installed four times, contact McAfee three times.  The last time I have contacted, I was told that Services Terminal Server for Windows is not running.  It is disabled and this is why the critical updates for McAfee will not download.

  By McAfee, I learned that I had to contact Microsoft to get a Server Terminal Services active again.

  Hello

  ·        You are able to install Windows Update on the system without any problems?

  I suggest you to check whether or not the Terminal Server service is enabled on the system. Follow the steps mentioned below.

  a. Click Start and click Run.

  b. type services.msc in the Run dialog box and press ENTER to open the services window.

  c. find the Terminal Server service on the system and right-click on it.

  d. set the startup type to automatic and then click apply and then click ok.

  e. now checks to see if you are able to download the update for McAfee on the system.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.